Supplemental Restraint Systems

Disposal

~8min read
4special tools

DISPOSAL

PRECAUTION / NOTICE / HINT

CAUTION:

Before disposing of any SRS component, read and carefully follow all environmental and hazardous material regulations. Deployment before disposal may be considered a hazardous material treatment.

PROCEDURE

1. PRECAUTIONS

CAUTION:

  • An airbag or pretensioner may be deployed accidentally by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this operation.
  • Never dispose of a curtain airbag assembly that has not been deployed.
  • The airbag makes an explosive noise when it deploys. Therefore, perform this operation outside, in a place where it will not disturb neighbors.
  • When deploying the airbag, always use the specified SST (SRS airbag deployment tool). Perform this operation in a place free from electrical noise.
  • Always stay at least 10 m (32.8 ft) away from the curtain airbag assembly when it is deployed.
  • The curtain airbag assembly becomes hot after deployment. Do not touch it for at least 30 minutes after deployment.
  • Wear gloves and protective glasses when handling a curtain airbag assembly that has been deployed.
  • Do not pour water or any other substance on a curtain airbag assembly that has been deployed.
  • Always wash your hands with water after completing the work.

HINT:

Before scrapping a vehicle equipped with the SRS system or disposing of a curtain airbag assembly, be sure to deploy the airbag first in accordance with the following procedure. If any abnormality occurs during airbag deployment, contact the TOYOTA MOTOR SALES, U.S.A, INC. service and repair department immediately.

2. DISPOSE OF CURTAIN AIRBAG ASSEMBLY (when installed in vehicle)

NOTICE:

  • When disposing of the curtain airbag assembly, never use the customer's vehicle to deploy the curtain airbag.
  • Be sure to perform the following procedure when deploying the airbag.

HINT:

Prepare a battery to be used as the power source for airbag deployment.

(a) Check that the SST operates correctly.

Click here

SST: 09082-00700

(b) Refer to the Precautions.

Click here

(c) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(d) Remove the headlining assembly.

Click here

(e) Disconnect the curtain airbag assembly connector.

(1) Using a screwdriver with its tip wrapped in protective tape, disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(f) Install the SST.

CAUTION:

Make sure nothing is loose in the curtain airbag assembly.

(1) After connecting the following SSTs to each other, connect them to the curtain airbag assembly.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To prevent damage to the SST connector or wire harness, do not engage the secondary lock of the double lock.

(2) Move the SST at least 10 m (32.8 ft) away from the rear side window of the vehicle.

*a

Battery

*b

10 m (32.8 ft) minimum

(3) Close all doors and windows of the vehicle, leaving enough space to route the SST wire harness through the rear side window.

NOTICE:

Be careful not to damage the SST wire harness.

(4) Connect the SST red clip to the battery positive (+) terminal and the SST black clip to the battery negative (-) terminal.

(g) Deploy the airbag.

(1) Make sure that no one is in the vehicle or within a 10 m (32.8 ft) radius of the vehicle.

(2) Press the SST activation switch to deploy the airbag.

CAUTION:

  • Before deploying, make sure no one is inside or near the vehicle.
  • The curtain airbag assembly becomes hot after deployment. Do not touch it for at least 30 minutes after deployment.
  • Wear gloves and protective glasses when handling a curtain airbag assembly that has been deployed.
  • Do not pour water or any other substance on a curtain airbag assembly that has been deployed.
  • Always wash your hands with water after completing the work.

HINT:

The airbag deploys when the LED on the SST activation switch lights up.

3. DISPOSE OF CURTAIN AIRBAG ASSEMBLY (when not installed in vehicle)

NOTICE:

Be sure to perform the following procedure when deploying the airbag.

HINT:

Prepare a battery to be used as the power source for airbag deployment.

(a) Check that the SST operates correctly.

Click here

SST: 09082-00700

(b) Remove the curtain airbag assembly.

Click here

CAUTION:

  • Before removing the curtain airbag assembly, wait at least 90 seconds after turning the ignition switch OFF and disconnecting the cable from the negative (-) battery terminal.
  • When registering the curtain airbag assembly, make sure the airbag deployment side faces upward.

    Deployment side

(c) Cut off the deployment section of the curtain airbag assembly.

(d) Using twisted wire, secure the curtain airbag assembly to an unused tire.

*a

Cable diameter

*b

Cross-sectional area of the grooved part of the cable

Cable:

Cross-section of the grooved part of the cable

1.25 mm2 (0.0019 in.2) minimum

CAUTION:

If the wire is too thin, or if another object is used to secure the curtain airbag assembly, it may snap off when the airbag deploys. Always use automotive wire with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).

HINT:

To calculate the cross-sectional area of the grooved part of the cable:

Cross-sectional area = 3.14 x (diameter)2 / 4

(1) Place the curtain airbag assembly in the tire as shown in the illustration.

Minimum tire dimensions:

Width

185 mm (7.28 in.)

Inside diameter

360 mm (1.18 ft)

CAUTION:

Make sure the wires are taut. If the wires are slack, the curtain airbag assembly may break off when the airbag deploys.

NOTICE:

Airbag deployment may damage the tire. Use an unused tire.

*a

Width

*b

Inside diameter

(e) Install the SST.

(1) After connecting the following SSTs to each other, connect them to the curtain airbag assembly.

SST: 09082-00802

09082-10801

09082-20801

(f) Place the tires.

CAUTION:

Do not position the curtain airbag assembly with its deployment direction facing the ground.

(1) Place at least 2 tires under the tire to which the curtain airbag assembly is secured.

Minimum tire dimensions:

Width

185 mm (7.28 in.)

Inside diameter

360 mm (1.18 ft)

NOTICE:

Do not place the SST connector under the tire, as this could damage it.

*a

Tires (2 minimum)

*b

Inside diameter

*c

Width

(2) Place at least 2 tires on top of the tire to which the curtain airbag assembly is secured. The top tire must be placed on a wheel.

NOTICE:

The wheel and tires may be damaged by airbag deployment. Make sure to use a wheel and tires that have not been used.

(3) Tie the tires together using 2 cables.

CAUTION:

Make sure the cables are tightly secured. If the cables are not tight, the tires will come apart when the airbag deploys.

(g) Install the SST.

(1) Connect the SST connector.

SST: 09082-00700

NOTICE:

To avoid damaging the SST connector or wire harness, do not engage the secondary lock of the double lock. Also, leave slack in the SST wire harness inside the tire.

*1

Curtain Airbag Assembly

*a

Battery

*b

10 m (32.8 ft) minimum

(2) Move the SST at least 10 m (32.8 ft) away from the airbag secured to the tire.

(h) Deploy the airbag.

(1) Connect the red SST clip to the battery positive (+) terminal and the black SST clip to the battery negative (-) terminal.

(2) Make sure no one is within 10 m (32.8 ft) of the tire to which the airbag assembly is secured.

(3) Press the SST activation switch to deploy the airbag.

CAUTION:

Before deploying the airbag, make sure no one is near the airbag.

HINT:

The airbag deploys when the LED on the SST activation switch lights up.

(i) Dispose of the curtain airbag assembly.

CAUTION:

  • The curtain airbag assembly becomes hot after deployment. Do not touch it for at least 30 minutes after deployment.
  • Wear gloves and protective glasses when handling a curtain airbag assembly that has been deployed.
  • Do not pour water or any other substance on a curtain airbag assembly that has been deployed.
  • Always wash your hands with water after completing the work.

(1) Remove the curtain airbag assembly from the tire.

(2) Place the curtain airbag assembly in a plastic bag, seal it tightly, and dispose of it in accordance with local regulations.