Exterior Panels / Trim

Installation

~4min read

INSTALLATION

PRECAUTION / NOTICE / HINT

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. INSTALL REAR DOOR WINDOW FRAME REAR MOULDING

(a) Using a pneumatic riveter or a hand riveter with a nose piece, install the rear door window frame rear moulding with 2 new rivets.

HINT:

If the rivet mandrel does not come out on the first use of the rivet gun, slide the rivet gun forward over the mandrel, then operate it again.

NOTICE:

  • Do not pry on the rivet with the riveter as this may damage the riveter and the mandrel.

    *a

    Rivet Gun

    *b

    Mandrel

    *c

    Incorrect

  • Make sure the rivets are seated firmly against the moulding.

    *a

    Rivet Gun

    *b

    Incorrect

  • Do not tilt the riveter when installing the rivet on the moulding.
  • Do not leave a gap between the rivet head and the moulding.
  • Do not leave a gap between the moulding and the door frame. Hold both parts firmly together while installing the rivet.

    *a

    Rivet Gun

    *b

    Incorrect

2. INSTALL REAR DOOR WINDOW FRAME UPPER MOULDING

(a) Engage the guides to temporarily install the rear door window frame upper moulding on the door frame.

(b) Using a pneumatic riveter or a hand riveter with a nose piece, install the rear door window frame upper moulding with 5 new rivets.

HINT:

If the rivet mandrel does not come out on the first use of the rivet gun, slide the rivet gun forward over the mandrel, then operate it again.

NOTICE:

  • Do not pry on the rivet with the riveter as this may damage the riveter and the mandrel.

    *a

    Rivet Gun

    *b

    Mandrel

    *c

    Incorrect

  • Make sure the rivets are seated firmly against the moulding.

    *a

    Rivet Gun

    *b

    Incorrect

  • Do not tilt the riveter when installing the rivet on the moulding.
  • Do not leave a gap between the rivet head and the moulding.
  • Do not leave a gap between the moulding and the door frame. Hold both parts firmly together while installing the rivet.

    *a

    Rivet Gun

    *b

    Incorrect

3. INSTALL REAR DOOR OUTSIDE MOULDING SUBASSEMBLY

HINT:

When installing a new rear door outside moulding subassembly, heat the vehicle body and the rear door outside moulding subassembly using a heat lamp.

Heating Temperature

Item

Temperature

Vehicle Body

40 à 60 °C

Rear Door Outside Moulding Subassembly

20 à 30 °C

CAUTION:

  • Do not touch heated parts or the heat lamp. Touching them may cause burns.
  • Prolonged contact with heated parts may cause burns.

*a

Hot Surface

*b

Heat Lamp

NOTICE:

Do not overheat the vehicle body or the rear door outside moulding subassembly.

(a) Clean the surface of the vehicle body.

(1) Using a heat light, heat the surface of the vehicle body.

(2) Remove the double-sided tape from the vehicle body.

(3) Remove any adhesive residue using a cleaning agent.

(b) Install a new rear door outside moulding subassembly.

(1) Using a heat lamp, heat the vehicle body and the rear door outside moulding subassembly.

(2) Remove the protective sheet from the rear door outside moulding subassembly.

HINT:

After removing the release liner, prevent the adhesive surface from contacting foreign matter.

(3) Engage the guide and clip, and attach the double-sided adhesive tape and sealing sponge to install the rear door outside moulding subassembly.

*a

Double-sided adhesive tape

Install in this direction (1)

Install in this direction (2)

HINT:

Press the rear door outside moulding subassembly firmly to install it.

(c) Remove the masking tape.

4. INSTALL REAR DOOR WEATHERSTRIP

Click here

5. INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Click here