Toyota Camry Quiz
Clutch

Clutch unit

In this manual: Clutch
Introduction — 61Audio & visual system — 16Automatic transmission / trans — 19Transmission revolution (ATM) — 1Shift lock system (ATM) — 1Brake — 20Clutch — 10Communication system — 4Cooling — 15Cruise control — 3Drive shaft / propeller shaft — 9Emission control — 8Engine control system — 12Engine hood/door — 7Exhaust — 3Exterior/interior trim — 14Front suspension — 9Fuel — 12Heater & air conditioner — 16Ignition — 8Instrument panel/meter — 7Intake — 7Lighting — 11Lubrication — 16Manual transmission/transaxle — 13Parking brake — 10Power steering — 7Rear suspension — 10Seat — 12Service specifications — 26Sliding roof/convertible — 4Starting & charging — 11Starting system (2AZ−FE)(From July, 2003) — 1Starting system (1MZ−FE/3MZ−FE) — 1Steering column — 6Theft deterrent & door lock — 9Tire & wheel — 4Windshield/windowglass/mirror — 5Back window glass — 1Power window control system — 1Power mirror control system — 1Inner rear view mirror assy — 1Windshield glass — 1Wiring — 1
17steps
~102min
4/5difficulty
010203040501914N·mlb·ft
Tightening torque found on this page
Done 0 of 17
OVERHAUL
  1. REMOVE MANUAL TRANSAXLE ASSY
  2. REMOVE CLUTCH RELEASE FORK BOOT
  3. REMOVE CLUTCH RELEASE BEARING ASSY
  4. REMOVE CLUTCH RELEASE FORK SUB−ASSY
  5. REMOVE RELEASE BEARING HUB CLIP
  6. REMOVE RELEASE FORK SUPPORT

a. Remove the release fork support from the manual transaxle assy.

7. REMOVE CLUTCH COVER ASSY

  1. Place the matchmarks on the clutch cover assy with the one on the flywheel sub−assy.

  2. Loosen each set bolt one turn at a time until spring tension is released.

  3. Remove the set bolts and pull off the clutch cover assy.

NOTICE: Do not drop the clutch disc assy. Remove clutch cover assy Remove clutch cover assy 8. REMOVE CLUTCH DISC ASSY NOTICE: Keep the lining part of the clutch disc assy, the pressure plate and surface of the flywheel sub−assy away from oil and foreign attachment. 9. INSPECT CLUTCH DISC ASSY

a. Using vernier calipers, measure the rivet head depth.

Maximum rivet depth: 0.3 mm (0.012 in.)

If necessary, replace the clutch disc assy.

b. Install the clutch disc assy to the transaxle assy.

NOTICE: Take care not to insert the clutch disc assy in the wrong direction

c. Using a dial indicator, check the clutch disc assy runout.

Minimum runout: 0.8 mm (0.031 in.)

If necessary, replace the clutch disc assy.

10. INSPECT CLUTCH COVER ASSY
10. INSPECT CLUTCH COVER ASSY

a. Using vernier calipers, inspect the diaphragm spring for depth and width of wear.

Maximum:
A (Depth): 0.5 mm (0.020 in.) B (Width): 6.0 mm (0.236 in.)

If necessary, replace clutch cover assy.

Inspect clutch cover assy
Inspect clutch cover assy 11. INSPECT FLYWHEEL SUB−ASSY

a. Using a dial indicator, inspect the flywheel sub−assy runout.

Maximum runout: 0.1 mm (0.004 in.)

If necessary, replace the flywheel sub−assy.

Inspect flywheel sub-assy Inspect flywheel sub-assy 12. INSPECT CLUTCH RELEASE BEARING ASSY

a. Turn the release bearing assy by hand while applying force in the axial direction.

HINT: The bearing is permanently lubricated and required no cleaning or lubrication.

If necessary, replace the release bearing assy.

Inspect clutch release bearing assy Inspect clutch release bearing assy 13. INSTALL CLUTCH DISC ASSY

a. Insert SST in the clutch disc assy, then insert them in the flywheel sub−assy.

SST 09301−00220

NOTICE: Take care not to insert clutch disc assy in the wrong direction. Install clutch disc assy Install clutch disc assy 14. INSTALL CLUTCH COVER ASSY

  1. Align the matchmarks on the clutch cover assy and flywheel sub−assy.

  2. Following the procedures shown in the illustration, tighten the 6 bolts, in the order starting the bolt locating near the knock pin on the top.

    Torque: 19 N·m

HINT:

  • Following the order in the illustration, tighten the bolts at a time evenly.

  • Move SST up and down, right and left lightly, after checking that the disc is in the center, tighten the bolts.

Install clutch cover assy
Install clutch cover assy 15. INSPECT AND ADJUST CLUTCH COVER ASSY

a. Using a dial indicator with roller instrument, check the diaphragm spring tip alignment.

Maximum non−alignment: 0.5 mm (0.020 in.)

If alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST 09333−00013

Inspect and adjust clutch cover assy
Inspect and adjust clutch cover assy 16. INSTALL RELEASE FORK SUPPORT

a. Install the release fork support to the manual transaxle assy.

Torque: 47 N·m 17. INSTALL RELEASE BEARING HUB CLIP a. Install the release bearing hub clip to the release bearing assy. 18. INSTALL CLUTCH RELEASE FORK SUB−ASSY

  1. Apply release hub grease to the release fork and release bearing assy contact, release fork and push rod contact and release fork pivot points.

    Sealant:
    Part No. 08887−01806, RELEASE HUB GREASE or equivalent

  2. Install the release fork to the release bearing assy.

19. INSTALL CLUTCH RELEASE BEARING ASSY

  1. Apply the clutch spline grease to the input shaft spline.

    Sealant:
    Part No. 08887−01706, CLUTCH SPLINE GREASE or equivalent

  2. Install the release fork with release bearing assy to the manual transaxle assy.

NOTICE: After the installation, move the folk forward and backward to check that the release bearing slides smoothly.
  1. INSTALL CLUTCH RELEASE FORK BOOT
  2. INSTALL MANUAL TRANSAXLE ASSY

Test yourself

A quick Toyota Camry quiz: every answer comes with an explanation and a link to the manual page.