Toyota Camry Quiz
Lubrication

Oil pump assy 1MZ−FE/3MZ−FE)

In this manual: Lubrication
Introduction — 61Audio & visual system — 16Automatic transmission / trans — 19Transmission revolution (ATM) — 1Shift lock system (ATM) — 1Brake — 20Clutch — 10Communication system — 4Cooling — 15Cruise control — 3Drive shaft / propeller shaft — 9Emission control — 8Engine control system — 12Engine hood/door — 7Exhaust — 3Exterior/interior trim — 14Front suspension — 9Fuel — 12Heater & air conditioner — 16Ignition — 8Instrument panel/meter — 7Intake — 7Lighting — 11Lubrication — 16Manual transmission/transaxle — 13Parking brake — 10Power steering — 7Rear suspension — 10Seat — 12Service specifications — 26Sliding roof/convertible — 4Starting & charging — 11Starting system (2AZ−FE)(From July, 2003) — 1Starting system (1MZ−FE/3MZ−FE) — 1Steering column — 6Theft deterrent & door lock — 9Tire & wheel — 4Windshield/windowglass/mirror — 5Back window glass — 1Power window control system — 1Power mirror control system — 1Inner rear view mirror assy — 1Windshield glass — 1Wiring — 1
78steps
~468min
4/5difficulty
0204060801004533N·mlb·ft
Tightening torque found on this page
Done 0 of 78
REPLACEMENT
  1. REMOVE FRONT WHEEL RH
  2. REMOVE FRONT FENDER APRON SEAL RH
  3. REMOVE ENGINE UNDER COVER RH
  4. DRAIN ENGINE OIL
a. Install a new gasket after draining engine oil. Torque: 45 N·m
  1. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER)
  2. REMOVE V BELT No. 1
  3. REMOVE VANE PUMP V BELT
  4. REMOVE ENGINE MOVING CONTROL ROD
  5. REMOVE ENGINE MOUNTING STAY No.2 RH
  6. REMOVE GENERATOR BRACKET No.2
  7. REMOVE CRANKSHAFT PULLEY
  8. REMOVE TIMING BELT No.1 COVER
  9. REMOVE TIMING BELT No.2 COVER
  10. REMOVE TIMING BELT GUIDE No.2
  11. REMOVE TIMING BELT
  12. REMOVE EXHAUST PIPE No.1 SUPPORT BRACKET
  13. REMOVE EXHAUST PIPE ASSY FRONT
  14. REMOVE EXHAUST PIPE SUPPORT BRACKET No.1
  15. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH

a. Remove the 2 bolts, nut and the drive belt adjusting bar bracket.

  1. Remove the 2 nuts, the generator bracket adjusting bar with wire harness clamp bracket.
  2. Disconnect the compressor, magnetic clutch connector and the wire harness clamp.
    d. Remove the 3 bolts, the compressor and magnetic clutch.

d. Remove the 3 bolts, the compressor and magnetic clutch.

HINT: Hang up the hoses instead of detaching.

  1. REMOVE TIMING BELT IDLER SUB−ASSY No.2
  2. REMOVE CAMSHAFT TIMING PULLEY
  3. REMOVE TIMING BELT IDLER SUB−ASSY No.1

a. Using a 10 mm socket hexagon wrench, remove the timing belt idler and plate washer.

  1. REMOVE CRANKSHAFT TIMING PULLEY
  2. REMOVE TIMING BELT No.3 COVER
  3. REMOVE COMPRESSOR MOUNTING BRACKET

No.1 a. Remove the 2 bolts and mounting bracket.

Remove compressor mounting bracket Remove compressor mounting bracket 26. REMOVE OIL LEVEL GAGE GUIDE

a. Remove the bolt and gage guide.

27. SEPARATE ENGINE MOUNTING INSULATOR FR

a. Remove the 3 nuts and bolt. Then separate the engine mounting insulator.

NOTICE: Do not remove the engine mounting insulator. Separate engine mounting insulator FR Separate engine mounting insulator FR 28. REMOVE ENGINE MOUNTING INSULATOR RH
  1. Remove the bolt and disconnect the power steering return hose clamp from the frame.
  2. Remove the 4 nuts.
  3. Prepare a jack. Place a wooden block on the jack and set the jack under the engine. Remove the engine mounting insulator.
  4. Raise the jack and lift up the engine. Then remove the engine mounting insulator RH.
NOTICE: Be careful not to damage the contact surfaces of the oil pan. Remove engine mounting insulator RH Remove engine mounting insulator RH 29. REMOVE ENGINE MOUNTING BRACKET RH

a. Remove the 4 bolts, nut and bracket.

Remove engine mounting bracket RH Remove engine mounting bracket RH 30. REMOVE OIL PAN SUB−ASSY No.2

a. Remove the 10 bolts, 2 nuts and oil pan.

b. Insert the blade of SST between the oil pan No. 1 and oil
b. Insert the blade of SST between the oil pan No. 1 and oil pan No. 2, cut through the sealer and remove oil pan No.2.

SST 09032−00100

NOTICE:
  • Do not damage the contact surface of oil pan No. 1 and oil pan No. 2.
  • Do not damage the flange portion of oil pan No.2 during removal.
31. REMOVE OIL STRAINER SUB−ASSY
31. REMOVE OIL STRAINER SUB−ASSY

a. Remove the bolt and 2 nuts, and remove the oil strainer and gasket.

32. REMOVE OIL PAN SUB−ASSY

a. Remove the 2 bolts and the flywheel housing under cover.

b. Uniformly loosen the 17 bolts and 2 nuts. Remove the

b. Uniformly loosen the 17 bolts and 2 nuts. Remove the bolts and nuts.

c. Using a screwdriver, remove the oil pan by prying the portions

c. Using a screwdriver, remove the oil pan by prying the portions between the cylinder block and oil pan shown in the illustration.

NOTICE: Be careful not to damage the contact surfaces of the cylinder block and oil pan.
33. REMOVE CRANKSHAFT POSITION SENSOR
33. REMOVE CRANKSHAFT POSITION SENSOR
  1. Disconnect the sensor connector.
  2. Remove the bolt and sensor.
34. REMOVE OIL PUMP ASSY
  1. Remove the 9 bolts.
  2. Using a screwdriver, remove the oil pump by prying between the oil pump and the main bearing cap.
  3. Remove the O−ring.
Remove oil pump assy Remove oil pump assy 35. INSTALL OIL PUMP ASSY a. Using SST and a hammer, install a new oil seal. Tap the surface of the SST with the hammer until the oil seal’s surface is flush with oil pump body edge.

SST 09223−00010

NOTICE:
  • Be careful not to tap the oil seal at an angle.
  • Keep the gap between the oil pump body edge and the oil seal free from contamination.
  1. Apply a small amount of MP grease to the oil seal lip.
  2. Remove any old seal packing material from the contact surface.
    d. Apply a light coat of engine oil to a new O−ring and place

d. Apply a light coat of engine oil to a new O−ring and place it on the cylinder block.

e. Apply a continuous bead of seal packing (diameter 2 to
e. Apply a continuous bead of seal packing (diameter 2 to 3 mm (0.08 to 0.12 in.)) as shown in the illustration.

Seal packing: Part No. 08226−00080 or equivalent

NOTICE:
  • Remove any oil from contact surface.
  • Apply seal packing to the inner side of the bolt holes.
  • Install the oil pump within 3 minutes after applying seal packing.
  • Do not expose the seal to engine oil for at least 2 hours after installing the oil pump.
f. Align the key of the oil pump drive gear with the key way

f. Align the key of the oil pump drive gear with the key way located on the crankshaft, and slide the oil pump into place.

g. Install the oil pump by tightening the 9 bolts uniformly.Torque:
g. Install the oil pump by tightening the 9 bolts uniformly.Torque: 8 N·m for bolt A 20 N·m for bolt B 43 N·m for bolt C
  1. INSTALL CRANKSHAFT POSITION SENSOR Torque: 8 N·m
  2. INSTALL OIL PAN SUB−ASSY
  3. Remove any old seal packing from the contact surface.
  4. Apply a continuous bead of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) as shown in the illustration. Seal packing: Part No. 08826−00080 or equivalent
NOTICE:
  • Remove any oil from the contact surface.
  • Apply seal packing to the outer side of the bolt holes in the region ”X”.
  • Apply seal packing to the inner side of the bolt holes in the region ”Y”.
  • Install the oil pan within 3 minutes after applying seal packing.
  • Do not expose the seal to engine oil for at least 2 hours after installing the oil pan.
  1. Install the oil pan No.1 by tightening the oil pan’s 17 bolts and 2 nuts uniformly. Torque: 8 N·m for 10 mm head 20 N·m for 12 mm head 37 N·m for 14 mm head
  2. Install the flywheel housing under cover with the 2 bolts. Torque: 7,8 N·m
Install oil pan sub-assy Install oil pan sub-assy 38. INSTALL OIL STRAINER SUB−ASSY a. Install a new gasket and the oil strainer with the bolt and 2 nuts.Torque: 8 N·m 39. INSTALL OIL PAN SUB−ASSY No.2
  1. Remove any old seal packing from the contact surface.
  2. Apply a continuous bead of seal packing (diameter 4 to 5 mm (0.16 to 0.20 in.)) as shown in the illustration. Seal packing: Part No. 08826−00080 or equivalent
NOTICE:
  • Remove any oil from the contact surface.
  • Apply seal packing to the inner side of the bolt holes.
  • Install the oil pan within 3 minutes after applying seal packing.
  • Do not expose the seal to engine oil for at least 2 hours after installing the oil pan.
c. Install the oil pan with the 10 bolts and 2 nuts.Torque: 8 N·m Install oil pan sub-assy No.2 Install oil pan sub-assy No.2 40. INSTALL ENGINE MOUNTING BRACKET RH Torque:
54 N·m for bolt A 54 N·m for nut B 43 N·m for bolt C Install engine mounting bracket RH Install engine mounting bracket RH 41. INSTALL ENGINE MOUNTING INSULATOR RH Torque:
95 N·m for nut A 87 N·m for nut B Install engine mounting insulator RH Install engine mounting insulator RH 42. INSTALL ENGINE MOUNTING INSULATOR FR Torque:
87 N·m for bolt A 52 N·m for nut B Install engine mounting insulator FR Install engine mounting insulator FR 43. INSTALL OIL LEVEL GAGE GUIDE a. Install a new O−ring, bolt and gage guide. Torque: 8 N·m
  1. INSTALL COMPRESSOR MOUNTING BRACKET No.1 Torque: 25 N·m
  2. INSTALL TIMING BELT No.3 COVER
  3. INSTALL TIMING BELT IDLER SUB−ASSY No.1
a. Using a 10 mm hexagon wrench, install the plate washer and idler pulley with the pivot bolt. Torque: 34 N·m
  1. INSTALL TIMING BELT IDLER SUB−ASSY No.2
  2. INSTALL CAMSHAFT TIMING PULLEY
  3. INSTALL COMPRESSOR AND MAGNETIC CLUTCH Torque: 25 N·m
  4. INSTALL EXHAUST PIPE SUPPORT BRACKET No.1
  5. INSTALL EXHAUST PIPE ASSY FRONT
  6. INSTALL EXHAUST PIPE No.1 SUPPORT BRACKET
  7. INSPECT TIMING BELT
  8. INSTALL TIMING BELT
  9. INSTALL TIMING BELT GUIDE No.2
  10. INSTALL TIMING BELT No.2 COVER
  11. INSTALL TIMING BELT No.1 COVER
  12. INSTALL CRANKSHAFT PULLEY
  13. INSTALL GENERATOR BRACKET No.2 Torque: 28 N·m
  14. INSTALL ENGINE MOUNTING STAY No.2 RH
  15. INSTALL ENGINE MOVING CONTROL ROD
  16. INSTALL VANE PUMP V BELT
  17. INSTALL V BELT No. 1
  18. INSPECT DRIVE BELT TENSION
  19. INSTALL FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) Torque: 80 N·m
  20. ADD ENGINE OIL
  21. INSPECT CHECK FOR ENGINE OIL LEAKS
  22. INSTALL FRONT WHEEL RH
  23. CHECK FOR EXHAUST GAS LEAKS
OVERHAUL 1. REMOVE OIL PUMP RELIEF VALVE

a. Remove the plug, spring and relief valve.

2. INSPECT OIL PUMP RELIEF VALVE
  1. Apply a light coat of engine oil.
  2. Check that the valve falls smoothly into the valve hole by its own weight.

If it does not, replace the relief valve. If necessary, replace the oil pump assy.

Inspect oil pump relief valve Inspect oil pump relief valve 3. INSPECT OIL PUMP COVER

a. Remove the 10 screws and the oil pump cover.

4. INSPECT OIL PUMP ROTOR

a. Apply a light coat of engine oil to the oil pump rotor set and place them into the oil pump body. Check that the rotors revolve smoothly.

If the result is not as specified, replace the oil pump assy.

b. Check the clearance between the drive tips and driven rotor grooves.

1. Insert a feeler gauge between each drive tip and driven rotor groove. Measure the clearances.Specified tip clearance: 0.060 to 0.300 mm (0.0024 to 0.0118 in.)

If the tip clearance is greater than the maximum, replace the oil pump assy.

c. Check the clearance between the driven rotor and body.

c. Check the clearance between the driven rotor and body.

1. Insert a feeler gauge between the driven rotor and body. Measure the clearance.Specified body clearance: 0.250 to 0.500 mm (0.0098 to 0.0128 in.)

If the body clearance is greater than the maximum, replace the oil pump assy.

d. Check the clearance between the drive and driven rotor.

d. Check the clearance between the drive and driven rotor.

1. Place a precision straight edge on the top surface of the drive. Insert a feeler gauge between the bottom edge of the precision straight edge and the top surface of the driven rotor. Measure the clearance.Specified side clearance: 0.030 to 0.150 mm (0.0012 to 0.0059 in.)

If the side clearance is greater than the maximum, replace the oil pump assy.

  1. REMOVE OIL PUMP ROTOR
  2. INSTALL OIL PUMP ROTOR

a. Apply a light coat of engine oil to the oil pump gear set and place it into the pump body with the marks facing the pump body cover side.

Install oil pump rotor Install oil pump rotor 7. INSTALL OIL PUMP COVER a. Install the oil pump cover with the 10 screws.Torque: 10 N·m 8. INSTALL OIL PUMP RELIEF VALVE
  1. Apply a light coat of engine oil to the relief valve, and insert the relief valve and spring into the pump body hole.
  2. Install the plug. Torque: 49 N·m

Test yourself

A quick Toyota Camry quiz: every answer comes with an explanation and a link to the manual page.