Toyota RAV4 Quiz
Supplemental restraint system

Lost communication with front satellite sensor bus rh

In this manual: Supplemental restraint system
Introduction — 37Interior — 12Exterior — 432Az-fe engine mechanical — 1552Az-fe ignition — 182Az-fe charging — 232Az-fe emission control — 82az-fe exhaust — 32Az-fe fuel — 72Az-fe lubrication — 4Brake — 17Brake control — 63U140f automatic transaxle — 59Instrument panel — 8Suspension — 18Drive shaft — 23Axle — 6Tire and wheel — 30Air conditioning — 93Lighting — 45Cruise control — 21Differential — 12Door lock — 31Engine immobiliser — 21Horn — 5Can communication — 27Mirror — 5Parking brake — 5Power steering — 27Propeller shaft — 3Seat — 29Seat belt — 27Sliding roof — 25Steering column — 6Wiper and washer — 11Supplemental restraint system — 95Other system — 5Maintenance — 14
36steps
~216min
4/5difficulty
Done 0 of 36
Toyota RAV4. Lost communication with front satellite sensor bus rh

Description

The front airbag sensor rh consists of the diagnostic circuit and the frontal deceleration sensor.

If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether or not the srs should be activated.

Dtc b1602/83, b1603/83, b1612/83 or b1613/83 is recorded when a malfunction is detected in the front airbag sensor rh circuit.

Toyota RAV4. Lost communication with front satellite sensor bus rh

Wiring diagram
Toyota RAV4. Lost communication with front satellite sensor bus rh

Inspection procedure
  1. Check connection of connector
  2. Turn the ignition switch off.
  3. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
  4. Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor rh.
Ok: the connectors are connected.


  1. Check front airbag sensor rh circuit (open)
Toyota RAV4. Check front airbag sensor rh circuit (open)

  1. Disconnect the connectors from the center airbag sensor and the front airbag sensor rh.
  2. Using a service wire, connect a29-2 (+sr) and a29-1 (- sr) of connector e.
Notice:

Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance of the wire harness side connector.
Standard resistance


  1. Check front airbag sensor rh circuit (short)
Toyota RAV4. Check front airbag sensor rh circuit (short)

  1. Disconnect the service wire from connector e.
  2. Measure the resistance of the wire harness side connector.
Standard resistance


  1. Check front airbag sensor rh circuit (to b+)
Toyota RAV4. Check front airbag sensor rh circuit (to b+)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
  2. Turn the ignition switch on.
  3. Measure the voltage of the wire harness side connector.
Standard voltage


  1. Check front airbag sensor rh circuit (to ground)
Toyota RAV4. Check front airbag sensor rh circuit (to ground)

  1. Turn the ignition switch off.
  2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
  3. Measure the resistance of the wire harness side connector.
Standard resistance


  1. Check front airbag sensor rh
Toyota RAV4. Check front airbag sensor rh

  1. Connect the connectors to the center airbag sensor .
  2. Interchange the front airbag sensor rh and lh, and connect the connectors to them.
  3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
  4. Turn the ignition switch on, and wait for at least 60 seconds.
  5. Clear the dtcs (see page rs-49).
  6. Turn the ignition switch off.
  7. Turn the ignition switch on, and wait for at least 60 seconds.
  8. Check the dtcs (see page rs-49).
Result
Hint:

Dtcs other than dtc b1602/83, b1603/83, b1612/83, b1613/83, b1607/84, b1608/84, b1617/84 and b1618/ 84 may be output at this time, but they are not related to this check.



Use simulation method to check
  1. Check engine room main wire (open)
Toyota RAV4. Check engine room main wire (open)

  1. Disconnect the service wire from connector e.
  2. Disconnect the engine room main wire connector from the instrument panel wire.
  3. Using a service wire, connect ae9-2 (+sr) and ae9-1 (- sr) of connector d.
Notice:

Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance of the wire harness side connector.
Standard resistance


Repair or replace instrument panel wire
  1. Check engine room main wire (short)
Toyota RAV4. Check engine room main wire (short)

  1. Disconnect the engine room main wire connector from the instrument panel wire.
  2. Disconnect the service wire from connector e.
  3. Measure the resistance of the wire harness side connector.
Standard resistance

Repair or replace instrument panel wire
  1. Check engine room main wire (to b+)
Toyota RAV4. Check engine room main wire (to b+)

  1. Turn the ignition switch off.
  2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
  3. Disconnect the engine room main wire connector from the instrument panel wire.
  4. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
  5. Turn the ignition switch on.
  6. Measure the voltage of the wire harness side connector.
Standard voltage

Repair or replace instrument panel wire
  1. Check engine room main wire (to ground)
Toyota RAV4. Check engine room main wire (to ground)

  1. Disconnect the engine room main wire connector from the instrument panel wire.
  2. Measure the resistance of the wire harness side connector.
Standard resistance


Repair or replace instrument panel wire

Test yourself

A quick Toyota RAV4 quiz: every answer comes with an explanation and a link to the manual page.