Toyota Tacoma Quiz
Cruise Control

Communication Error from VSC to ECM Invalid Serial Data Received (P163081)

In this manual: Cruise Control
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
3steps
~18min
2/5difficulty
Done 0 of 3
DESCRIPTION

The skid control ECU (master cylinder solenoid)*1 or skid control ECU (brake actuator assembly)*2 sends signals such as cruise control cancel signals and brake demand response signals to the ECM when the dynamic radar cruise control system is operating.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

P163081

Communication Error from VSC to ECM Invalid Serial Data Received

While the vehicle speed is 36 km/h or more and the dynamic radar cruise control system is operating, communication data from the skid control ECU (master cylinder solenoid)*1 or skid control ECU (brake actuator assembly)*2 is logically inconsistent for approximately 0.5 second or more.
  • Vehicle stability control system
  • ECM

Does not come on
  • *1: for Hydraulic Brake Booster
  • *2: for Vacuum Brake Booster
CAUTION / NOTICE / HINT

NOTICE:

  • First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

    Click here

  • Before replacing the ECM, refer to Registration.

    w/o Smart Key System: Click here w/ Smart Key System: Click here

    w/ Smart Key System: Click here

PROCEDURE

  1. CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

(a) Check for DTCs.

for Hydraulic Brake Booster: Click here for Vacuum Brake Booster: Click here

for Vacuum Brake Booster: Click here

Result

Proceed to

DTCs are not output

A

DTCs are output (for Hydraulic Brake Booster)

B

DTCs are output (for Vacuum Brake Booster)

C
B

GO TO VEHICLE STABILITY CONTROL SYSTEM
C

GO TO VEHICLE STABILITY CONTROL SYSTEM
A

  1. CHECK FOR DTCs (CRUISE CONTROL SYSTEM)

(a) Clear the DTCs.

Click here (b) Perform the following procedure.

(b) Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

  1. Turn the ignition switch to ON.
  2. Turn the dynamic radar cruise control system on using the cruise control main switch.
  3. Drive the vehicle at 36 km/h or more for 1 second or more.

(c) Check for DTCs.

Click here

Result

Proceed to

DTC P163081 is not output

A

DTC P163081 is output

B
A

USE SIMULATION METHOD TO CHECK
B

REPLACE ECM

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.