DESCRIPTION
The ECM stores this DTC when a communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
B2799 |
Engine Immobiliser System Malfunction |
One of the following conditions is met:
- Error in communication between ECM and transponder key ECU assembly.
- Error in communication lines.
- Communication ID is different during communication between ECM and transponder key ECU assembly.
|
- Harness or connector
- Transponder key ECU assembly
- ECM
|
DTC Output Confirmation Operation:
- Start the engine and wait 10 seconds.
- After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.
|
Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
Engine cannot be started |
- |
Related Data List and Active Test
DTC No. | Data List and Active Test |
B2799 |
- |
WIRING DIAGRAM
NOTICE:
- If the transponder key ECU assembly or ECM is replaced, refer to Registration.
Click here 
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
HINT:
If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.
PROCEDURE
CLEAR DTC
(a) Clear the DTCs.
Click here 
| NEXT |
 |
|
CHECK FOR DTC
(a) Start the engine.
(b) Check for DTCs.
Click here 
HINT:
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
OK:
DTC B2799 is not output.
Result | Proceed to |
OK |
A |
NG (B2799 is output) |
B |
NG (Other DTCs are output) |
C |
| A |
 |
USE SIMULATION METHOD TO CHECK |
| C |
 |
GO TO DIAGNOSTIC TROUBLE CODE CHART |
| B |
 |
|
CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)
(a) Using an oscilloscope, check the waveform.
*a |
Component with harness connected
(Transponder Key ECU Assembly) |
*b |
Waveform |
Measurement Condition:
Item | Content |
Tester Connection |
J26-12 (EFII) - Body ground |
Tool Setting |
2 V/DIV., 500 ms./DIV. |
Condition |
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
OK:
Waveform is similar to that shown in the illustration.
Result | Proceed to |
OK |
A |
NG (Terminal EFII stuck low (2.4 V or less)) |
B |
NG (Terminal EFII stuck high (12 V) or abnormal waveform) |
C |
| B |
 |
GO TO STEP 10 |
| C |
 |
GO TO STEP 16 |
| A |
 |
|
CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
(a) Using an oscilloscope, check the waveform.
*a |
Component with harness connected
(Transponder Key ECU Assembly) |
*b |
Waveform |
Measurement Condition:
Item | Content |
Tester Connection |
J26-13 (EFIO) - Body ground |
Tool Setting |
2 V/DIV., 500 ms./DIV. |
Condition |
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
OK:
Waveform is similar to that shown in the illustration.
| NG |
 |
GO TO STEP 12 |
| OK |
 |
|
REGISTER ECU COMMUNICATION ID
(a) Reregister the ECU communication ID.
Click here 
| NEXT |
 |
|
CHECK WHETHER ENGINE STARTS
(a) Using a registered key, turn the ignition switch to ON.
(b) Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
| OK |
 |
END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) |
| NG |
 |
|
REPLACE ECM
(a) Temporarily replace the ECM with a new one.
- for 1UR-FE:
Click here 
- for 3UR-FE:
Click here 
- for 3UR-FBE:
Click here 
| NEXT |
 |
|
REGISTER ECU COMMUNICATION ID
(a) Reregister the ECU communication ID.
Click here 
| NEXT |
 |
|
CHECK WHETHER ENGINE STARTS
(a) Using a registered key, turn the ignition switch to ON.
(b) Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
| OK |
 |
END (ECM WAS DEFECTIVE) |
| NG |
 |
REPLACE TRANSPONDER KEY ECU ASSEMBLY |
CHECK ECM (IMO TERMINAL VOLTAGE)
(a) Disconnect the ECM connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Result |
A24-29 (IMO) - Body ground*1
A24-48 (IMO) - Body ground*2 |
Ignition switch turned to ON using registered key |
Terminal IMO stuck low (2.4 V or less) |
Terminal IMO stuck high (12 V) |
- *1: for 1UR-FE
- *2: for 3UR-FE, 3UR-FBE
|
 |
*A |
for 1UR-FE |
*B |
for 3UR-FE, 3UR-FBE |
*a |
Front view of wire harness connector
(to ECM) |
|
|
Result | Proceed to |
Terminal IMO stuck low (2.4 V or less) |
A |
Terminal IMO stuck high (12 V) or abnormal waveform |
B |
| B |
 |
GO TO STEP 7 |
| A |
 |
|
CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)
(a) Disconnect the J26 transponder key ECU assembly connector.
(b) Disconnect the A24 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance: for 1UR-FE
Tester Connection | Condition | Specified Condition |
J26-12 (EFII) - A24-29 (IMO) |
Always |
Below 1 Ω |
A24-29 (IMO) - Body ground |
Always |
10 kΩ or higher |
J26-12 (EFII) - Body ground |
Always |
10 kΩ or higher |
for 3UR-FE, 3UR-FBE
Tester Connection | Condition | Specified Condition |
J26-12 (EFII) - A24-48 (IMO) |
Always |
Below 1 Ω |
A24-48 (IMO) - Body ground |
Always |
10 kΩ or higher |
J26-12 (EFII) - Body ground |
Always |
10 kΩ or higher |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
REPLACE TRANSPONDER KEY ECU ASSEMBLY
(a) Replace the transponder key ECU assembly with a new one.
Click here 
| NEXT |
 |
|
REGISTER KEY
(a) Register the key.
Click here 
| NEXT |
 |
|
REGISTER ECU COMMUNICATION ID
(a) Register the ECU communication ID.
Click here 
| NEXT |
 |
|
CHECK WHETHER ENGINE STARTS
(a) Using a registered key, turn the ignition switch to ON.
(b) Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
| OK |
 |
END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE) |
| NG (for 1UR-FE) |
 |
REPLACE ECM |
| NG (for 3UR-FE) |
 |
REPLACE ECM |
| NG (for 3UR-FBE) |
 |
REPLACE ECM |
CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)
(a) Disconnect the J26 transponder key ECU assembly connector.
(b) Disconnect the A24 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance: for 1UR-FE
Tester Connection | Condition | Specified Condition |
J26-12 (EFII) - A24-29 (IMO) |
Always |
Below 1 Ω |
A24-29 (IMO) - Body ground |
Always |
10 kΩ or higher |
J26-12 (EFII) - Body ground |
Always |
10 kΩ or higher |
for 3UR-FE, 3UR-FBE
Tester Connection | Condition | Specified Condition |
J26-12 (EFII) - A24-48 (IMO) |
Always |
Below 1 Ω |
A24-48 (IMO) - Body ground |
Always |
10 kΩ or higher |
J26-12 (EFII) - Body ground |
Always |
10 kΩ or higher |
| OK |
 |
GO TO STEP 7 |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|