Vehicle Interior
Theft Deterrent System Communication Line High Fixation (B279A)
DESCRIPTION
When the communication line (EFIO-IMI) between the transponder key ECU assembly and ECM is stuck on HI output, the ECM stores this DTC.
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
Note
B279A
Theft Deterrent System Communication Line High Fixation
The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output (1 trip detection logic*).
Harness or connector
ECM
Transponder key ECU assembly
Turn the ignition switch to ON and wait 6 seconds.
*: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops)
Engine cannot be started
Related Data List and Active Test
DTC No.
Data List and Active Test
B279A
-
WIRING DIAGRAM
NOTICE:
If the transponder key ECU assembly or ECM is replaced, refer to Registration. Click here
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
CHECK CONNECTION OF CONNECTOR
(a) Check that the connectors are properly connected to the ECM and transponder key ECU assembly.
OK:
Connectors are properly connected.
NG
CONNECT CONNECTORS PROPERLY
OK
CHECK ECM (IMI TERMINAL VOLTAGE)
(a) Disconnect the transponder key ECU assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
J26-13 (EFIO) - Body ground
Always
11 to 14 V
*a
Front view of wire harness connector
(to Transponder Key ECU Assembly)
(c) Connect the transponder key ECU assembly connector.
NG
GO TO STEP 4
OK
CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
(a) Using an oscilloscope, check the waveform.
*a
Component with harness connected
(Transponder Key ECU Assembly)
*b
Waveform
Measurement Condition:
Item
Content
Tester Connection
J26-13 (EFIO) - Body ground
Tool Setting
2 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
OK:
Waveform is similar to that shown in the illustration.
OK (for 1UR-FE)
REPLACE ECM
OK (for 3UR-FE)
REPLACE ECM
OK (for 3UR-FBE)
REPLACE ECM
NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)
CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM AND BODY GROUND)
(a) Disconnect the A24 ECM connector.
(b) Disconnect the J26 transponder key ECU assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for 1UR-FE
Tester Connection
Condition
Specified Condition
J26-13 (EFIO) - A24-40 (IMI)
Always
Below 1 Ω
A24-40 (IMI) - Body ground
Always
10 kΩ or higher
J26-13 (EFIO) - Body ground
Always
10 kΩ or higher
for 3UR-FE, 3UR-FBE
Tester Connection
Condition
Specified Condition
J26-13 (EFIO) - A24-46 (IMI)
Always
Below 1 Ω
A24-46 (IMI) - Body ground
Always
10 kΩ or higher
J26-13 (EFIO) - Body ground
Always
10 kΩ or higher
OK (for 1UR-FE)
REPLACE ECM
OK (for 3UR-FE)
REPLACE ECM
OK (for 3UR-FBE)
REPLACE ECM
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Was this page helpful? 👍 Yes 👎 No