DESCRIPTION
When the position control ECU and switch assembly does not receive a sensor signal despite forward or rearward movement of the seatback by power seat motor operation, this DTC is stored.
DTC Code | DTC Detection Condition | Trouble Area |
B2651 |
The forward and rearward lock detection position of the sensor is the same. |
- Position control ECU and switch assembly
- Front seatback frame sub-assembly LH (reclining motor)
- Harness or connector
|
WIRING DIAGRAM
PROCEDURE
PERFORM ACTIVE TEST USING TECHSTREAM (SEAT RECLINING)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Driver Seat / Active Test.
(e) Perform the Active Test according to the display on the Techstream. Driver Seat
Tester Display | Test Part | Control Ranger | Diagnostic Note |
Seat Reclining |
Seat reclining operation |
Front / OFF / Rear |
- |
OK:
Motor operates normally.
| NG |
 |
GO TO STEP 5 |
| OK |
 |
|
CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)
(a) Disconnect the front seatback frame sub-assembly LH (reclining motor) connector. |
 |
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
Z6-4 - Z6-3 |
Reclining switch on |
4.8 to 5.1 V |
Text in Illustration
*a |
Front view of wire harness connector
(to Front Seatback Frame Sub-assembly LH [Reclining Motor]) |
| NG |
 |
GO TO STEP 4 |
| OK |
 |
|
CHECK FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)
(a) Reconnect the front seatback frame sub-assembly LH (reclining motor) connector. |
 |
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
Z6-4 - Body ground |
Reclining switch on |
4.5 to 4.8 V |
Text in Illustration
*a |
Component with harness connected
(Front Seatback Frame Sub-assembly LH [Reclining Motor]) |
| OK |
 |
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY |
| NG |
 |
REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH |
CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
(a) Disconnect the Z10 position control ECU and switch assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
Z10-11 (SSRR) - Z6-4 |
Always |
Below 1 Ω |
Z10-1 (SGND) - Z6-3 |
Always |
Below 1 Ω |
Z10-11 (SSRR) or Z6-4 - Body ground |
Always |
10 kΩ or higher |
Z10-1 (SGND) or Z6-3 - Body ground |
Always |
10 kΩ or higher |
| OK |
 |
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)
(a) Remove the front seatback frame sub-assembly LH (reclining motor) (See page ).
(b) Inspect the front seatback frame sub-assembly LH (reclining motor) (See page ).
| NG |
 |
REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
(a) Disconnect the Z9 position control ECU and switch assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
Z9-9 (RCL+) - Z6-2 |
Always |
Below 1 Ω |
Z9-11 (RCL-) - Z6-1 |
Always |
Below 1 Ω |
Z9-9 (RCL+) or Z6-2 - Body ground |
Always |
10 kΩ or higher |
Z9-11 (RCL-) or Z6-1 - Body ground |
Always |
10 kΩ or higher |
| OK |
 |
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|