DESCRIPTION
When the position control ECU and switch assembly does not receive a sensor signal despite forward or rearward movement of the seat by power seat motor operation, this DTC is stored.
DTC Code | DTC Detection Condition | Trouble Area |
B2650 |
The forward and rearward lock detection position of the sensor is the same. |
- Position control ECU and switch assembly
- Front seat cushion frame sub-assembly LH (slide motor)
- Harness or connector
|
WIRING DIAGRAM
PROCEDURE
PERFORM ACTIVE TEST USING TECHSTREAM (SEAT SLIDE OPERATION)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Driver Seat / Active Test.
(e) Perform the Active Test according to the display on the Techstream. Driver Seat
Tester Display | Test Part | Control Range | Diagnostic Note |
Seat Slide Operation |
Seat sliding operation |
Front / OFF / Rear |
- |
OK:
Motor operates normally.
| NG |
 |
GO TO STEP 5 |
| OK |
 |
|
CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)
(a) Disconnect the front seat cushion frame sub-assembly LH (slide motor) connector. |
 |
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
Z3-5 - Z3-6 |
Sliding switch on |
4.8 to 5.1 V |
Text in Illustration
*a |
Front view of wire harness connector
(to Front Seat Cushion Frame Sub-assembly LH [Slide Motor]) |
| NG |
 |
GO TO STEP 4 |
| OK |
 |
|
CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE MOTOR)
(a) Reconnect the front seat cushion frame sub-assembly LH (slide motor) connector. |
 |
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
Z3-5 - Body ground |
Sliding switch on |
4.5 to 4.8 V |
Text in Illustration
*a |
Component with harness connected
(Front Seat Cushion Frame Sub-assembly LH [Slide Motor]) |
| OK |
 |
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY |
| NG |
 |
REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH |
CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
(a) Disconnect the Z10 position control ECU and switch assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
Z10-5 (SSRS) - Z3-5 |
Always |
Below 1 Ω |
Z10-1 (SGND) - Z3-6 |
Always |
Below 1 Ω |
Z10-5 (SSRS) or Z3-5 - Body ground |
Always |
10 kΩ or higher |
Z10-1 (SGND) or Z3-6 - Body ground |
Always |
10 kΩ or higher |
| OK |
 |
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE MOTOR)
(a) Remove the front seat cushion frame sub-assembly LH (slide Motor) (See page ).
(b) Inspect the front seat cushion frame sub-assembly LH (slide motor) (See page ).
| NG |
 |
REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
(a) Disconnect the Z9 position control ECU and switch assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
Z9-3 (SLD+) - Z3-4 |
Always |
Below 1 Ω |
Z9-4 (SLD-) - Z3-3 |
Always |
Below 1 Ω |
Z9-3 (SLD+) or Z3-4 - Body ground |
Always |
10 kΩ or higher |
Z9-4 (SLD-) or Z3-3 - Body ground |
Always |
10 kΩ or higher |
| OK |
 |
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|