Toyota Venza Quiz
U660e Automatic Transmission / Transaxle

Installation

In this manual: U660e Automatic Transmission / Transaxle
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~1min read
010203040505.44N·mlb·ft
Tightening torque found on this page
INSTALLATION PROCEDURE

1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

(a) Move the shift lever to N.

(b) Align the protrusions of the park/neutral position switch.

Text in Illustration

*1

Protrusion

(c) Install the park/neutral position switch to the control shaft with the 2 bolts.

Torque:

5,4 N·m {55 kgf·cm, 48 in·lbf}

NOTICE:

  • Before installing the park/neutral position switch, remove any dirt or rust on the installation portion of the control shaft. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch cannot be reinstalled correctly.
  • After installing the park/neutral position switch, confirm that the 2 protrusions on the switch are aligned.

(d) Install the transmission control shaft lever to the control shaft with the nut and washer.

Torque:

13 N·m {130 kgf·cm, 9 ft·lbf}

(e) Connect the connector to the park/neutral position switch.

(f) Connect the transmission control cable to the transmission control cable bracket with a new clip.

(g) Connect the transmission control cable to the transmission control shaft lever with the nut.

Torque:

13 N·m {130 kgf·cm, 9 ft·lbf}

2. INSTALL AIR CLEANER BRACKET

(a) Install the air cleaner bracket with the 3 bolts.

Torque:

7,8 N·m {80 kgf·cm, 69 in·lbf}

(b) Install the wire harness clamp.

3. INSTALL AIR CLEANER CASE


4. INSTALL AIR CLEANER CAP WITH HOSE


5. INSTALL INLET NO. 2 AIR CLEANER


6. INSTALL COOL AIR INTAKE DUCT SEAL


7. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION


8. INSPECT SHIFT LEVER POSITION


9. ADJUST SHIFT LEVER POSITION

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.