Volkswagen Tiguan Quiz
6-Speed Manual Transmission 02Q, OBB, and OFB

Clutch Mechanism

In this manual: 6-Speed Manual Transmission 02Q, OBB, and OFB
Body exterior — 50Body Interior — 29General Paint Information — 69Paint — 9Brake System — 16Suspension, Wheels, Steering — 68Wheel and Tire Guide — 3Towing Guide — 1Wheel and Tire Guide General Information — 23Communication — 20Electrical Equipment General Information — 29Electrical Equipment from 06/2011 — 59Heating, Ventilation and Air Conditioning — 24Refrigerant R134a Servicing — 296-Speed Manual Transmission 02Q, OBB, and OFB — 27
45steps
~270min
4/5difficulty
010203040502518N·mlb·ft
Tightening torque found on this page
Done 0 of 45

Component Location Overview - Clutch Mechanism

Volswagen Tiguan. Component Location Overview - Clutch Mechanism
  1. Chapter "Overview - Pedal Assembly, Scirocco, CC, Golf Cabriolet, Passat and Tiguan"
    Chapter "Overview - Pedal Assembly, Golf, Golf Wagon"
  2. Chapter "Overview - Clutch Hydraulics, Scirocco, CC, Golf Cabriolet, Passat and Tiguan"
    Chapter "Overview - Clutch Hydraulics, Golf, Golf Wagon"
  3. Chapter "Overview - Clutch Hydraulics, Scirocco, CC, Golf Cabriolet, Passat and Tiguan, RHD Vehicle"
    Chapter "Overview - Clutch Hydraulics, Golf, Golf Wagon, RHD Vehicle"

Overview - Pedal Assembly

Overview - Pedal Assembly, Scirocco, CC, Golf Cabriolet, Passat and Tiguan

Note

  • Lubricate all bearing areas and contact surfaces.
  • Grease allocation. Refer to the Parts Catalog.
Volswagen Tiguan. Overview - Pedal Assembly, Scirocco, CC, Golf Cabriolet, Passat and Tiguan
  1. Bulkhead
    • With a mount for the mounting bracket
  2. Seal
    • Self-adhesive
    • Replace after removing the mounting bracket
    • Attached to the mounting bracket
  3. Mounting Bracket
    • For the clutch pedal mount
    • Some equipment versions have a damper.
    • Removing and installing.
  4. Bolt
  5. Over-Center Spring
    • Lubricate all bearing areas and contact surfaces.
    • Grease allocation. Refer to the Parts Catalog.
    • Removing and installing.
  6. Bearing Bushing
  7. Mounting Pin
    • Lubricate all bearing areas and contact surfaces.
    • Grease allocation. Refer to the Parts Catalog.
  8. Clutch Pedal
    • Lubricate all bearing areas and contact surfaces.
    • Grease allocation. Refer to the Parts Catalog.
    • Removing and installing.
  9. Base Plate
    • Lubricate all bearing areas and contact surfaces.
    • Grease allocation. Refer to the Parts Catalog.
    • To remove and install, disconnect the clutch master cylinder from the clutch pedal.
  10. Seal
    • Replace after removing
    • Between the clutch master cylinder and the mounting bracket
  11. Clutch Master Cylinder
    • Removing and installing.
  12. Clutch Position Sensor -G476-
    • Can be checked in Guided Fault Finding. Refer to Vehicle Diagnostic Tester.
    • Allocation. Refer to the Parts Catalog.
    • Removing and installing.
  13. Clamp
    • The clamp must be removed in order to remove/install the hose/line assembly
  14. Hose
    • Made of plastic.
  15. Nut
    • 25 N·m
    • Replace after removing
    • For the mounting bracket to the bulkhead
    • Quantity: 3
    • Self-locking
  16. Nut
    • 25 N·m
    • Replace after removing
    • Self-locking
  17. Stop
    • For the clutch pedal

Plastic Hose -1-

  • The seals -2- must be inside the hose.
  • Replace with the hose if damaged
Volswagen Tiguan. N30-10128

Mounting Bracket with Damper -arrow-

Volswagen Tiguan. N30-10195

Overview - Clutch Hydraulics

Overview - Clutch Hydraulics, Scirocco, CC, Golf Cabriolet, Passat and Tiguan

Volswagen Tiguan. Overview - Clutch Hydraulics, Scirocco, CC, Golf Cabriolet, Passat and Tiguan
  1. Brake Fluid Reservoir
  2. Spring Clamp
    • Not on all vehicles
  3. Hose
    • Rubber
    • Made of plastic.
  4. Clutch Master Cylinder
    • Removing and installing.
  5. Clamp
    • To remove and install the hose/line assembly or pipe, pull the clamp all the way out.
    • On some clutch master cylinders, it is pulled out on the side
  6. Seal/O-Ring
    • Replace if damaged
    • Install on the line connection
    • Install with brake fluid
    • Seals/O-rings suitable for the line connection material.
    • Allocation. Refer to the Parts Catalog.
  7. Base Plate
    • To remove and install, disconnect the clutch master cylinder from the clutch pedal.
  8. Clutch Pedal
    • Removing and installing.
  9. Nut
    • Tightening specification.
  10. Hose/Line Assembly
    • Allocation. Refer to the Parts Catalog.
    • To remove, remove the battery and battery tray.
    • Removing and installing.
  11. Bracket
    • For hose/line assembly
    • Attached to the body
    • Covered by the assembly mounting
    • Bracket differentiation.
  12. Line
    • Allocation. Refer to the Parts Catalog.
    • To remove, remove the battery and battery tray.
    • Removing and installing.
  13. Bracket
    • For the pipe line
    • Attached to the body
    • Covered by the assembly mounting
    • Bracket differentiation.
  14. Seal/O-Ring
    • Replace if damaged
    • Install on the line connection
    • Install with brake fluid
    • Seals/O-rings suitable for the line connection material.
    • Allocation. Refer to the Parts Catalog.
  15. Bleeder
    • Removing and installing.
  16. Clamp
    • The clamp must be removed in order to remove/install the hose/line assembly
  17. Breather Valve
    • Bleed clutch mechanism.
    • With hex fitting - tightening specification: 4,5 N·m
    • Flat on both sides: seal off to stop.
  18. Dust Cap
  19. Clutch Slave Cylinder
    • Removing and installing.
  20. Transmission

Bracket Differentiation

Volswagen Tiguan. N30-10151
Dimension "a" mm Line Version
8 Line
6 Hose/Line Assembly

Overview - Clutch Release Mechanism

Volswagen Tiguan. Overview - Clutch Release Mechanism
  1. Clutch Slave Cylinder with Release Bearing
    • Must be replaced together because they are a single unit
    • Do not wash the bearing, just wipe it off.
    • Replace a loud bearing together with the clutch slave cylinder
    • Removing and installing.For release bearing with additional plastic washer.
    • Allocation. Refer to the Parts Catalog.
  2. Bolt
    • 12 N·m for metal clutch slave cylinder (without locking fluid)
    • 15 N·m for plastic clutch slave cylinder (with locking fluid)
    • Replace after removing
    • Pay attention to the thread pitch on the bolt when cleaning the threaded hole in the clutch housing.
    • Carefully tighten diagonally and in step so that the tabs on the clutch slave cylinder do not break
    • Quantity: 3
  3. Clamp
    • To remove and install the line, remove the clip up to the stop
    • Install until the clip engages audibly
  4. Line
    • To the clutch master cylinder
  5. O-Ring
    • Replace if damaged
    • Install on the line connection
    • Install with brake fluid
    • Allocation. Refer to the Parts Catalog.

Release Bearing with Additional Plastic Washer

Identified by: tabs -arrow- on the plastic washer.

Volswagen Tiguan. N30-10361

Only for Release Bearing with Additional Plastic Washer: Pressure Plate Diaphragm Spring (-arrows-) with a Slightly Lower Installation Height.

  • Install the release bearing with additional plastic washer and the pressure plate diaphragm spring with a slightly lower installation height.
Volswagen Tiguan. A30-0152

Clutch Master and Clutch Slave Cylinder, Checking

Before replacing the clutch master cylinder due to an assumed defect, perform the Guided Fault Finding first. Refer to Vehicle Diagnostic Tester.

Clutch Position Sensor -G476-, Removing and Installing
  • Chapter "Clutch Position Sensor -G476-, Removing and Installing, Scirocco, CC, Golf Cabriolet and Passat"
  • Chapter "Clutch Position Sensor -G476-, Removing and Installing, Tiguan"
  • Chapter "Clutch Position Sensor -G476-, Removing and Installing, Golf, Golf Wagon"
Over-Center Spring, Removing and Installing
  • Chapter "Over-Center Spring, Removing and Installing, CC, Passat"
  • Chapter "Over-Center Spring, Removing and Installing, Tiguan"
  • Chapter "Over-Center Spring, Removing and Installing, Golf and Golf Wagon"

Clutch Pedal, Removing and Installing

  • Chapter "Clutch Pedal, Removing and Installing, CC, Passat"
  • Chapter "Clutch Pedal, Removing and Installing, Tiguan"
  • Chapter "Clutch Pedal, Removing and Installing, Golf, Golf Wagon"

Mounting Bracket, Removing and Installing

  • Chapter "Mounting Bracket, Removing and Installing, Scirocco and Golf Cabriolet"
  • Chapter "Mounting Bracket, Removing and Installing, CC, Passat"
  • Chapter "Mounting Bracket, Removing and Installing, Golf, Golf Wagon"
  • Chapter "Mounting Bracket, Removing and Installing, Tiguan"

Clutch Master Cylinder, Removing and Installing

Clutch Master Cylinder, Removing and Installing, Scirocco, CC, Golf Cabriolet, Passat and Tiguan

Special tools and workshop equipment required

  • Clutch Pedal Pliers -T10005-

Removing

Note

  • Before replacing the clutch master cylinder due to a suspected defect, perform the Guided Fault Finding first. Refer to Vehicle Diagnostic Tester.
  • When working inside the footwell, cover the carpet with cloths to protect it from leaking brake fluid.
  • Remove the mounting bracket.
  • Release the mount for the clutch master cylinder actuator rod using the Clutch Pedal Pliers -T10005-.
  • Place a spacer -A- between the clutch pedal and the stop and push the clutch pedal down as far as the spacer.
Volswagen Tiguan. A30-0118

Spacer length = approximately 40 mm (for example, 1/2 socket insert)

  • Unlock the securing clip -B- and remove the clutch master cylinder from the mounting bracket -arrow 1- and in direction of -arrow 2-.
Volswagen Tiguan. A30-0119

Installing

Move the clutch pedal into its rest position.

  • Attach the mount -2- to the clutch master cylinder actuator rod -1-.
Volswagen Tiguan. A30-0120
  • Place a spacer -A- between the clutch pedal and the stop and push the clutch pedal down as far as the spacer.
Volswagen Tiguan. A30-0121

Spacer length = approximately 40 mm (for example, 1/2 socket insert)

  • Lock the clutch master cylinder to the mounting bracket in direction of -arrow 1 and arrow 2-.
  • Push the clutch master cylinder actuator rod -1- in direction of -arrow- until the mount -2- audibly engages inside the clutch pedal.
  • Install the mounting bracket.
Volswagen Tiguan. A30-0122

Bleeder, Removing and Installing

Hose/Line Assembly or Pipe -4- on Bleeder -1-, Removing and Installing

  • To remove, open the clip -2- with a screwdriver or a pointed tool and pull off hose/line assembly or pipe -4- at bleeder -1-.
  • To install, press hose/line assembly or pipe with new O-ring -3- onto the bleeder connection, until clip audibly engages.
  • Pull on the line to make sure it is secure.
Volswagen Tiguan. A30-0136

Removing and Installing the Bleeder -4- from the Clutch Slave Cylinder

  • To remove, open the clip -2- with a screwdriver or a pointed tool and remove bleeder -4- from clutch slave cylinder -1-.
  • To install, check the O-ring -3- on the clutch slave cylinder. Press in the bleeder at the clutch slave cylinder connector until the clip -2- engages audibly.
  • To check, pull on the bleeder.
Volswagen Tiguan. A30-0137

Disconnect and Connect Clutch Mechanism Wires

Separating

  • Open the clip -3- with a screwdriver and remove the hose/line assembly -1- from the connection -4-.
Volswagen Tiguan. A30-10096

Connecting

Note

  • An O-ring can also be installed instead of a seal -2-.
  • Replace the damaged seal -2-.
  • Press in the hose/line assembly -1- at the connection -4- until the clip -3- engages audibly.
  • Pull on the hose/line assembly to make sure it is secure.
Volswagen Tiguan. N30-10294

Sealing Rings/O-Rings for Hose/Line Assembly or Pipe

Item Line Connection Version
1 Line connection with a groove all the way around -arrow 1-
2 Line connection with a shoulder -arrow 2-
3 Line connection with a shoulder -arrow 2- and with a groove all the way around -arrow 3-

The seal / O-ring must be installed in the groove -arrow 1- and -arrow 3-.

  • Bleed the clutch mechanism.
Clutch Mechanism Lines, Removing and Installing

Special tools and workshop equipment required

  • Hose Clamps - Up To 25 mm -3094-

Removing

  • Disconnect the battery.
  • Remove the air filter housing if the lines are not accessible.

Continuation for All

  • Remove the battery and the battery tray.

Caution

Danger of leaking brake fluid.

  • Be careful not to get any brake fluid on the longitudinal member or on the transmission when performing the following work. If it does, clean the area thoroughly.
  • Place a lint-free cloth under the clutch master cylinder.

Clamp off the hose -2- to the clutch master cylinder using Hose Clamps - Up To 25mm -3094-.

Volswagen Tiguan. N30-10419

Note

  • A slight deformation of the hose remains after the Hose Clamps - Up To 25mm -3094- have been removed.
  • The hose is not faulty.
  • After removing the Hose Clamps - Up To 25mm -3094-, the hose must be formed back into its original shape.
  • Remove clip for hose/line assembly -1- all the way and remove hose/line assembly.
  • Seal off openings.
  • Remove the clip -arrow- all the way and then remove the hose/line assembly -A- from the bleeder.
Volswagen Tiguan. A34-10522

Ignore -B-.

  • Seal the open lines and connections with clean plugs if necessary from the Engine Bung Set -VAS6122-.
  • Free up the hose/line assembly and remove it.

Installing

Install in the reverse order of removal while noting the following:

  • Connect hose/line assembly -1- with clutch master cylinder.
  • Pull on the line to make sure it is secure.
Volswagen Tiguan. N30-10419
  • Push the hose/line assembly -4- with the O-ring -3- onto the bleeder connection -1- until the clip -2- audibly locks into place.
  • Pull on the line to make sure it is secure.

After removing the Hose Clamp up to 25 mm -3094-, the return hose -2- (⇒ previous illustration) must be formed back into its original shape.

Volswagen Tiguan. A30-0136
  • Bleed the clutch mechanism.
  • Install the air filter housing.

Continuation for All

  • Install the battery tray, battery and the battery cover.

Clutch Slave Cylinder with Release Bearing, Removing and Installing

Special tools and workshop equipment required

  • Torque Wrench 1331 5-50Nm -VAG1331-

Note

  • The clutch slave cylinder and the release bearing are a single unit and are replaced together.
  • Pay attention to the thread pitch on the bolts when cleaning the threaded hole in the clutch housing.

Removing

Transmission is removed.

  • Open the clip -2- with a screwdriver or a pointed tool and remove bleeder -4- from clutch slave cylinder -1-.
  • Remove the bolts -arrows-.
Volswagen Tiguan. A30-0137
  • Remove the clutch slave cylinder together with the release bearing -A-.
Volswagen Tiguan. A30-0012

Installing

Install in the reverse order of removal while noting the following:

  • Tighten the slave cylinder bolts in small increments only.

Otherwise, there is the danger that the tabs with the fastening holes could break off.

  • Check the O-ring -3- on the clutch slave cylinder for damage.
  • Push the bleeder -4- onto the clutch slave cylinder connection -1- until the clip -2- clicks into place.
  • To check, pull on the bleeder.
  • Install the transmission.
  • Bleed the clutch mechanism.
Volswagen Tiguan. A30-0137

Tightening Specifications

  • Clutch slave cylinder with release bearing to transmission.

Clutch Mechanism, Bleeding

Special tools and workshop equipment required

  • Brake Charger/Bleeder Unit -VAS5234-

Note

  • Bleed the system after working on the hydraulic clutch mechanism.
  • Make sure no brake fluid gets on the transmission when performing the following work.
  • It is not necessary to pre-fill the system.
  • Fill the brake fluid reservoir up to the "Max" marking with brake fluid before bleeding.
  • The clutch pedal is in the neutral position and is not pressed.
  • Brake fluid allocation. Refer to the Parts Catalog.
  • Remove the air filter housing if it makes the bleeder inaccessible.

Continuation for All

  • Return clutch pedal to the rest position.
  • Remove cap from the breather valve -arrow-.
  • Connect the Brake Charger/Bleeder Unit -VAS5234-.

If necessary use the Bleeder Hose (670 mm) -VAG1238/B3-.

  • Connect the bleed hose -A- with the collector bottle pressure hose.
  • Switch the Brake Charger/Bleeder Unit -VAS5234- on.

Working pressure 2.0 bar (29 psi).

  • Open the breather valve approximately 1/4 turn.
  • Move the clutch pedal manually 15 to 20 time very quickly from stop to stop.
  • Close the breather valve and switch the Brake Charger/Bleeder Unit -VAS5234- off.
Volswagen Tiguan. N30-0311
  • Breather valve with hex fitting: Tightening specification, 4,5 N·m
  • Breather valve flattened on both sides: seal off all the way
  • After completing the bleeding procedure, and the pressure has dropped from 2 bar (29 psi), operate the clutch pedal an additional 10 times by foot.
  • Install the air filter housing.

Clutch Release Mechanism, Servicing

Special tools and workshop equipment required

  • Torque Wrench 1331 5-50Nm -VAG1331-
  • Grease for Clutch Disc Shaft Splines
  • Grease allocation. Refer to the Parts Catalog.

The transmission is removed.

  • Remove and attach the clutch slave cylinder with the release bearing -arrows-.
Volswagen Tiguan. A30-0012

Clutch Slave Cylinder -A- with Divided Supply Line

The supply line is divided in area with -arrows- on some clutch slave cylinders

Allocation. Refer to the Parts Catalog.

Volswagen Tiguan. N30-10136

Release Bearing with Additional Plastic Washer

Identified by: tabs -arrow- on the plastic washer.

Volswagen Tiguan. N30-10361

Only for Release Bearing with Additional Plastic Washer: Pressure Plate Diaphragm Spring (-arrows-) with a Slightly Lower Installation Height.

  • Install the release bearing with additional plastic washer and the pressure plate diaphragm spring with a slightly lower installation height.
Volswagen Tiguan. A30-0152

Allocation. Refer to the Parts Catalog.

  • Install the transmission.
  • Bleed the clutch mechanism.

Tightening Specifications

  • Clutch slave cylinder with release bearing to transmission.

Test yourself

A quick Volkswagen Tiguan quiz: every answer comes with an explanation and a link to the manual page.