5-speed manual transmission 0CF

Input shaft

21steps
~126min
4/5difficulty
Done 0 of 21

Assembly overview - driveshaft


Note

  • When installing new gears or a new driveshaft, observe technical data and → Electronic Parts Catalogue (ETKA).
  • Heat gears to max. 120 °C.
  • Replace both tapered roller bearings together.
  • Install all bearings on driveshaft lubricated with gearbox oil.
  • Heat bearing inner races/tapered roller bearings to 100 °C before installation.
VW UP. 5 Gang-Schaltgetriebe 0CF

  1. Transmission housing
  2. Outer race/tapered roller bearing
    • Pull off
    • Press in
  3. Inner race/tapered roller bearing
    • Press off
    • Press on
  4. Input shaft
    • adjust
  5. 3rd gear wheel
    • Press off
    • Installation position: collar faces 4th gear
    • Press on
  6. Circlip
    • replace after removal
  7. Circlip
    • replace after removal
  8. 4th gear wheel
    • press off together with 5th gear wheel
    • Installation position: collar faces 3rd gear
    • Press on
  9. 5th gear wheel
    • press off together with 4th gear wheel
    • Installation position: higher collar faces 4th gear
    • Press on
  10. Circlip
    • replace after removal
  11. Inner race/tapered roller bearing
    • Press off
    • Press on
  12. Outer race/tapered roller bearing
    • Pull off
    • Press in
  13. Adjusting shim
    • Determine thickness
  14. Clutch housing

Disassemble and assemble driveshaft

VW UP. 5 Gang-Schaltgetriebe 0CF

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Pressure plate -VW 401-
  • Pressure plate -VW 402-
  • Pressure ram -VW 407-
  • Pressure ram -VW 408 A-
  • Pressure ram -VW 411-
  • Pressure ram -VW 412-
VW UP. 5 Gang-Schaltgetriebe 0CF

  • -1- Internal puller 36...46 mm, e.g. -Kukko 21/6-
  • -3- Separator 12...75 mm, e.g. -Kukko 17/1-
  • -3- Separator 25...155 mm, e.g. -Kukko 17/3-
  • -3- Separator 30...120 mm, e.g. -Kukko 15/2-
  • -4- Counter support, e.g. -Kukko 22/2-
  • Pressure piece -T10428-
  • Pressure plate -40 - 105-
  • Drift tube -32 - 109-
  • Attachment -30 - 23-
  • Tube section -VW 426-

Pull outer race/tapered roller bearing out of clutch housing

  1. Counter support, e.g. -Kukko 22/2-
  2. Internal puller 36... 46 mm, e.g. -Kukko 21/6-
    VW UP. 5 Gang-Schaltgetriebe 0CF

Press outer race/tapered roller bearing into clutch housing

- Insert adjusting shim.

VW UP. 5 Gang-Schaltgetriebe 0CF

Press off inner race/tapered roller bearing on clutch housing side

  1. Separator 12... 75 mm, e.g. -Kukko 17/1-
VW UP. 5 Gang-Schaltgetriebe 0CF

Press on inner race/tapered roller bearing on clutch housing side

VW UP. 5 Gang-Schaltgetriebe 0CF

Pull outer race/tapered roller bearing out of transmission housing

  1. Counter support, e.g. -Kukko 22/2-
  2. Separator 25... 155 mm, e.g. -Kukko 17/3-
  3. Internal puller 36... 46 mm, e.g. -Kukko 21/6-
    VW UP. 5 Gang-Schaltgetriebe 0CF

Press outer race/tapered roller bearing into transmission housing

VW UP. 5 Gang-Schaltgetriebe 0CF

Press off inner race/tapered roller bearing on transmission housing side

  1. Separator 12... 75 mm, e.g. -Kukko 17/1-
VW UP. 5 Gang-Schaltgetriebe 0CF

Press on inner race/tapered roller bearing on transmission housing side

Disassemble output shaft


Note

Press off inner race/tapered roller bearing for bearing in clutch housing.

- Remove circlip.

VW UP. 5 Gang-Schaltgetriebe 0CF

Press off 5th gear and 4th gear wheels together

  1. Separator 30... 120 mm, e.g. -Kukko 15/2-
VW UP. 5 Gang-Schaltgetriebe 0CF

- Remove circlips -arrows-.

VW UP. 5 Gang-Schaltgetriebe 0CF

Press off 3rd gear wheel

Assemble output shaft

VW UP. 5 Gang-Schaltgetriebe 0CF

Installation position of 3rd gear wheel and 4th gear wheel

3rd gear wheel -A- and 4th gear wheel -B- face each other with the collar -arrow-.

They are secured with circlips -1- and -2-.

VW UP. 5 Gang-Schaltgetriebe 0CF

Press on 3rd gear wheel

VW UP. 5 Gang-Schaltgetriebe 0CF

- Install new circlips -arrows-.

VW UP. 5 Gang-Schaltgetriebe 0CF

Press on 4th gear wheel

VW UP. 5 Gang-Schaltgetriebe 0CF

Installation position of 5th gear wheel

The higher collar -arrow- points toward 4th gear wheel.

VW UP. 5 Gang-Schaltgetriebe 0CF

Press on 5th gear wheel

- Install circlip.


Note

Press on inner race/tapered roller bearing for bearing in clutch housing.

VW UP. 5 Gang-Schaltgetriebe 0CF

Adjust output shaft

(Determine adjusting shim for output shaft)

VW UP. 5 Gang-Schaltgetriebe 0CF

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Clamping block -VW 313-
  • Gearbox holder -T10484-
  • Gauge block plate -VW 385/17-
  • Universal dial gauge holder -VW 387-
  • Pressure ram -VW 412-
  • Pressure piece -T10428-
  • Torque Wrench -V.A.G 1331-
  • Dial gauge -VAS 6080A-
  • Dial gauge extension 30 mm
  • -1- Internal puller 36...46 mm, e.g. -Kukko 21/6-
  • -4- Counter support, e.g. -Kukko 22/2-

Readjusting the output shaft is required if the following components are replaced:

  • Transmission housing
  • Clutch housing
  • Input shaft

or the

  • tapered roller bearing

Adjustment overview

Requirement:

  • Sealing surfaces of clutch housing and transmission housing must be cleaned of sealant.
  • Both inner races for the tapered roller bearings are pressed onto the output shaft.
  • The outer race/tapered roller bearing is pressed into the transmission housing.
VW UP. 5 Gang-Schaltgetriebe 0CF

- Press outer race/tapered roller bearing into clutch housing up to the stop without adjusting shim.

- Insert output shaft into transmission housing and assemble clutch housing. Tighten hex bolts to tightening torque.

VW UP. 5 Gang-Schaltgetriebe 0CF

- Install measuring device and dial gauge in clutch housing.

- Turn output shaft before measuring so the tapered roller bearings seat. Set dial gauge to "0" with 1 mm preload.


Note

Repeat this procedure before each further measurement, otherwise the dial gauge will not return to its starting position.

- Pull output shaft toward dial gauge.

- Read and record clearance on dial gauge (example 0.930).

- Determine thickness of adjusting shim from table; (example 0.930) part number → Electronic Parts Catalog (ETKA):

VW UP. 5 Gang-Schaltgetriebe 0CF

Remove transmission housing and pull outer race/tapered roller bearing out of clutch housing

  1. Counter support, e.g. -Kukko 22/2-
  2. Internal puller 36... 46 mm, e.g. -Kukko 21/6-

- Assemble transmission housing and tighten new hex bolts to tightening torque.

Table of adjusting shims

VW UP. 5 Gang-Schaltgetriebe 0CF




Perform check measurement

- Install measuring device and dial gauge.

- Turn output shaft so the tapered roller bearings seat.

- Pull output shaft toward dial gauge.

- Bearing clearance must be min. 0.140... max. 0.184 mm.

VW UP. 5 Gang-Schaltgetriebe 0CF

Replace oil seal for output shaft

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Release lever -T20143/2-
VW UP. 5 Gang-Schaltgetriebe 0CF

  • Pressure piece -T40008-
  • Sealing grease -G 052 128 A1-

- Remove manual transmission.

- Remove clutch release lever with release bearing and guide sleeve

VW UP. 5 Gang-Schaltgetriebe 0CF

Pry out oil seal for output shaft


Note

Do not damage running surface for oil seal on output shaft.

VW UP. 5 Gang-Schaltgetriebe 0CF

- Fill half of the space between sealing lip and dust lip of new oil seal with sealing grease.

- Lightly wet outer circumference of oil seal with transmission oil.

VW UP. 5 Gang-Schaltgetriebe 0CF

Drive oil seal for output shaft in flush

- Install clutch release lever with release bearing and guide sleeve

- Install manual transmission.

VW UP. 5 Gang-Schaltgetriebe 0CF