Body

Actuator, Removing and Installing

~6min read
010203040502015N·mlb·ft
Tightening torque found on this page

Rear Lid Motor 1 -V444-, Removing and Installing, Sedan

WARNING

Adapt the Rear Lid Motor 1 -V444- whenever it is removed and installed. Use Guided Functions in Guided Fault Finding and diagnostic address 6D. Refer to Vehicle Diagnostic Tester.

Rear Lid Motor 1 -V444-, Removing and Installing, Sedan

1 - Rear Lid Motor 1 -V444-

  • Removing
    • Disconnect the connector from the motor.
    • Remove the Rear Lid Motor 1 -V444- from the rear ball stud.
    • Remove the bolts from the bracket -5- and lift the Rear Lid Motor 1 -V444- out of the vehicle.
    • Pull the Rear Lid Motor 1 -V444- off the ball studs on the bracket.
  • Installing
    • Push the Rear Lid Motor 1 -V444- onto the ball studs on the bracket and then tighten it.

2 - Ball Stud

  • 20 N·m

3 - Rear Lid Hinge

4 - Bolt

  • 21 N·m

5 - Bracket

6 - Plastic clip

  • Must be removed using needle nose pliers. Refer to → Chapter "Gas-Filled Strut with Clip, Removing and Installing"

Rear Lid Motor 1 and 2 -V444-/-V445-, Removing and Installing, Avant

WARNING

Perform an adaptation using Guided Functions in Guided Fault Finding under diagnosis address 6D after removing and installing Rear Lid Motor 1 -V444- or Rear Lid Motor 2 -V445-. Refer to Vehicle Diagnostic Tester.

Rear Lid Motor 1 and 2 -V444-/-V445-, Removing and Installing, Avant

1 - Rear Lid Motor 2 -V445-

  • The rear roof panel trim is removed. Refer to → Body Interior; Rep. Gr.70; Roof Trim Panels.
  • Loosen the D-pillar trim in the drive area, and if necessary, carefully push it aside.
  • On vehicles with power luggage compartment cover the D-pillar trim panel must be completely removed.

Note

  • Remove or install drive unit only when rear lid is completely open.
  • Before removing driving unit, loosen lock nuts on eccentric bolts.
  • Remove the connector -2-.
  • Loosen the lock nut on the drive unit.

Note

The eccentric bolt -item 1- must be loose in the hinge arm hole.

  • Release tension on eccentric bolts with a brief turn to the right, if necessary.
  • Remove the bolt -5- on the bracket -4-.
  • Remove the screw in the hinge arm -item 7- and remove the drive unit -1- sideways.

2 - Bolt

  • 21 N·m

3 - Connector

  • Disconnect the connector before removing the drive unit.

4 - Bracket

Note

  • Bracket is positioned with a device in factory and must not be adjusted.
  • If bracket must be replaced, for example, when doing repairs after an accident, proceed as follows.
  • Rear lid must be installed with the gas-filled strut.
  • Secure the bracket -4- lightly with a screw -5- on the drive unit first.
  • Bracket must still be moveable.
  • Attach drive unit on rear lid hinge parallel to axle until it comes in contact with motor socket.

Caution

Drive unit bushing must fit flat against hinge axle collar.

  • Secure the bracket -4- on the body side with the bolt -3- and tighten to 21 N·m.
  • Tighten the bolt -5- to 8 N·m.
  • Tighten the eccentric bolt with the lock nut to the drive unit to the tightening specification.

Note

  • Upon tightening locking nuts, eccentric bolts are braced in hinge with no play.
  • For this reason, you cannot counterhold eccentric bolt hex head with an open-end wrench when tightening locking nuts.
  • When removing drive unit, this tension is released with a small turn to the right on eccentric bolt hex head, after you have loosened locking nuts.
  • Tighten the bolt to the drive fork. Refer to -item 7- to the tightening specification.

5 - Bolt

  • 8 N·m

6 - Roof Frame

7 - Bolt

  • Self-threading
  • Tightening specification. Refer to -item 7-.

8 - Lid Hinge

  • Removing and installing. Refer to → Chapter "Hinges, Removing and Installing, Avant".

Install the Rear Lid Motor 2 -V445- in the Hinge.

Install the Rear Lid Motor 2 -V445- in the Hinge.

1 - Hex Head Eccentric Bolts

Note

  • Upon tightening locking nuts, eccentric bolts are braced in hinge with no play.
  • For this reason, you cannot counterhold eccentric bolt hex head with an open-end wrench when tightening locking nuts.
  • When removing drive unit, this tension is released with a small turn to the right on eccentric bolt hex head, after you have loosened locking nuts.

2 - Washer

3 - Lock Nut

  • Before removing drive unit, loosen lock nuts on eccentric bolts.
  • Release eccentric bolt tension in hinge arm by rotating hex head to right, if necessary.
  • Self-locking
  • 6 N·m

4 - Rear Lid Motor 2 -V445-

  • When installing, insert sideways with socket -arrow B- and loose eccentric bolts -arrow A- in hinge.

Note

Drive unit socket must fit flat against hinge axle collar.

  • The drive unit arm then moves correctly on the rear lid hinge arm -8-.
  • Tighten the screw -6- to the tightening specification to attach the drive unit to the bracket -5-.
  • Tighten the locking nuts -3- to the tightening specification
  • Tighten the bolt -7- to the tightening specification.

5 - Bracket

Note

  • Bracket is positioned with a device in factory and should not be adjusted.
  • If bracket must be replaced, for example, when doing repairs after an accident, proceed as follows.

6 - Bolt

  • 8 N·m

7 - Bolt

  • 21 N·m
  • Self-threading

8 - Lid Hinge

  • Removing and installing. Refer to → Chapter "Hinges, Removing and Installing, Avant".

Rear Lid Control Module -J605-, Removing and Installing, Sedan

Removing

- Remove the luggage compartment side trim panel. Refer to → Body Interior; Rep. Gr.70; Luggage Compartment Trim Panels; Luggage Compartment Side Trim Panel, Removing and Installing.

- Disconnect the connectors from the control module.

- Open the retainers -arrows- and remove the control module -1- to the rear.

Installing

Install in reverse order of removal. Note the following:

- Insert the control module into the bracket and then slide it forward until it clicks into place.

A55-10798

Rear Lid Control Module -J605-, Removing and Installing, Avant

Removing

- Remove the rear roof trim panel. Refer to → Body Interior; Rep. Gr.70; Roof Trim Panels; Roof End Strip, Removing and Installing.

- Disconnect electrical connectors.

- Open the retainers -arrows- and remove the control module -1- to the side.

Installing

Install in reverse order of removal. Note the following:

- Insert the control module into the bracket and then slide it forward until it clicks into place.

A55-10799