Body

Overview - Rear Lid

~3min read
010203040502115N·mlb·ft
Tightening torque found on this page

Overview - Rear Lid, Sedan

Overview - Rear Lid, Sedan

1 - Rear Lid

  • Removing and installing. Refer to → Chapter "Rear Lid, Removing and Installing, Sedan".

2 - Stop Strip

3 - Adjusting Buffer

  • Adjusting

4 - Rear Lid Latch

  • Removing and installing. Refer to → Chapter "Rear Lid Lock, Removing and Installing, Sedan".

5 - Nut

  • 21 N·m

6 - Spring

  • Attachment points

7 - Lid Hinge

  • Removing and installing. Refer to → Chapter "Hinges, Removing and Installing, Sedan".

8 - Nut

  • 21 N·m

9 - Bracket

10 - Nut

  • 21 N·m

11 - Bolt

  • 21 N·m

12 - Bolt

  • 21 N·m

13 - Rear Lid Motor 1 -V444-

  • Removing and installing. Refer to → Chapter "Rear Lid Motor 1 -V444-, Removing and Installing, Sedan".

14 - Side Stop

  • Removing and installing. Refer to → Chapter "Side Stop Buffer, Removing and Installing, Sedan through Model Year 2014".

Overview - Rear Lid, Sedan, Hinge Cable Guide

Overview - Rear Lid, Sedan, Hinge Cable Guide

1 - Rear Lid Hinge Cable Guide

  • Removing and installing. Refer to → Body Interior; Rep. Gr.70; Luggage Compartment Trim Panels; Lower Rear Lid Trim Panel, Removing and Installing

2 - Expanding Clip

3 - Rear Lid Emergency Release

  • Routing → Chapter "Lid Latch Emergency Release, Removing and Installing, Sedan"

4 - Lid Hinge

5 - Tab

6 - Rear Lid

Overview - Rear Lid, Avant

Overview - Rear Lid, Avant

1 - Rear Lid

  • Removing and installing. Refer to → Chapter "Rear Lid, Removing and Installing, Avant".

2 - Lid Latch

  • Removing. Refer to → Chapter "Hood Latch, Removing and Installing, Avant".

3 - Cover

4 - Nuts

  • 21 N·m

5 - Cover

6 - Adjusting Buffer

  • Adjusting

7 - Screws

  • 8 N·m

8 - Stop

9 - Bolt

  • 8 N·m

10 - Bolt

  • 21 N·m

11 - Bolt

  • 30 N·m

12 - Rear Lid Motor 2 -V445-

13 - Lid Hinge

  • Removing. Refer to → Chapter "Hinges, Removing and Installing, Avant".

14 - Ball Stud

  • 21 N·m

15 - Gas-Filled Strut

  • Noise insulation element must be engaged in rear lid side.
  • Push the insulation onto the ball stud while turning it gently.

Overview - Rear Lid, Rear Lid Motor, Sedan

Overview - Rear Lid, Rear Lid Motor, Sedan

1 - Rear Lid Motor 1 -V444-

  • Removing and installing. Refer to → Chapter "Rear Lid Motor 1 -V444-, Removing and Installing, Sedan".

2 - Ball Stud

  • 20 N·m

3 - Rear lid hinge

4 - Bolt

  • 21 N·m

5 - Bracket

6 - Plastic Clip

  • Release with needle nose pliers. Refer to → Chapter "Gas-Filled Strut with Clip, Removing and Installing".

Overview - Rear Lid, Rear Lid Motor, Avant

Overview - Rear Lid, Rear Lid Motor, Avant

1 - Rear Lid Motor 2 -V445-

  • Removing and installing. Refer to → Chapter "Rear Lid Motor 1 and 2 -V444-/-V445-, Removing and Installing, Avant".

2 - Bolt

  • 21 N·m

3 - Connector

  • Disconnect the connector before removing the drive unit.

4 - Bracket

  • Bracket is positioned with a device in factory and must not be adjusted.

5 - Bolt

  • 8 N·m

6 - Roof Frame

7 - Bolt

  • Self-threading
  • Tightening specification

8 - Lid Hinge

  • Removing and installing. Refer to → Chapter "Hinges, Removing and Installing, Avant".