Body

Rear Lid, Removing and Installing

~3min read
010203040502115N·mlb·ft
Tightening torque found on this page

Rear Lid, Removing and Installing, Sedan

Rear Lid, Removing and Installing, Sedan

1 - Rear Lid

  • A second technician will be needed during removal and installation to support and to hold the rear lid.
  • Removing:

Note

Mark the position of the rear lid on the rear lid hinge with a felt-tip pen before removing.

  • Remove the rear lid trim panel. Refer to → Body Interior; Rep. Gr.70; Luggage Compartment Trim Panels; Lower Rear Lid Trim Panel, Removing and Installing
  • Disconnect the electric wires on the connectors and pull them out of the rear lid.
  • Remove the nuts on the rear lid side and then remove the rear lid.
  • Install in reverse order of removal.
  • The springs -6- must be engaged before installing the rear lid.
  • Adjusting:
    • Adjust the front height and the position of the hood lengthwise using the hood hinge.
    • Adjust the height of the back of the rear lid by adjusting the rear lid latch.
    • Align the hood so it is centered according to the gap dimensions. Refer to → Chapter "Rear Lid, Adjusting".
    • Adjusting buffer stops
  • Rear Lid Seal, Removing and installing. Refer to → Chapter "Rear Lid Seal, Replacing Sedan".

2 - Stop Strip

3 - Adjusting Buffer

4 - Rear Lid Latch

5 - Nut

6 - Spring

7 - Lid Hinge

8 - Nut

  • 21 N·m

9 - Bracket

10 - Nut

  • 21 N·m

11 - Bolt

  • 21 N·m

12 - Bolt

  • 21 N·m

13 - Rear Lid Motor 1 -V444-

14 - Side Stop

Rear Lid, Removing and Installing, Avant

Rear Lid, Removing and Installing, Avant

1 - Rear Lid

  • Removing:
  • Remove the rear lid trim panel. Refer to → Body Interior; Rep. Gr.70; Luggage Compartment Trim Panels; Upper Rear Lid Trim Panel, Removing and Installing
  • Disconnect the connectors and remove the hose for the rear window washer system.
  • A second technician will be needed to hold and to lift the rear lid.
  • Pull the gas-filled struts off the rear lid.
  • Remove the bolts from the left and right hinges on the rear lid.
  • Remove the rear lid.

2 - Lid Latch

3 - Cover

4 - Nuts

5 - Cover

6 - Adjusting Buffer

7 - Screws

8 - Stop

9 - Bolt

10 - Bolt

  • 21 N·m

11 - Bolt

  • 30 N·m

12 - Rear Lid Motor 2 -V445-

13 - Lid Hinge

14 - Ball Stud

15 - Gas-Filled Strut

  • Noise insulation element must be engaged in rear lid side.
  • Push the insulation onto the ball stud while turning it gently.

Side Stop Buffer, Removing and Installing, Sedan through Model Year 2014

Side Stop Buffer, Removing and Installing, Sedan through Model Year 2014

1 - Stop, Body Side

  • Removing.
    • Install the stop buffer into the hole and push the slider all the way in.

2 - Stop, Rear Lid Side

  • Removing.
    • Install the stop buffer into the hole and push the slider all the way in.

3 - Rear Lid

4 - Side Panel

Removing the Side Stop Buffer

- Pull the slider -1- in direction of the -arrow- out of the stop.

- Remove the stop from the side panel or rear lid.

A55-10778

Stop and Adjusting buffer, Removing And Installing, Avant

Stop and Adjusting buffer, Removing And Installing, Avant

1 - Adjusting Buffer

  • Adjusting

2 - Stop

3 - Bolt

  • 8 N·m

4 - Bolt

  • 8 N·m

Adjusting buffer Installed Position

Adjusting buffer Installed Position

1 - Rear Lid

  • When adjusted correctly, adjusting buffer -3- must contact stop buffer -2- with light pretension when rear lid is closed.

2 - Stop

3 - Adjusting Buffer

  • There is an adjusting screw for adjusting the height.
  • When rear lid is adjusted correctly, adjusting buffer must make contact with light pre-tension with stop on rear lid side.

4 - Side Panel