Engine Electrical System
In this manual: Engine Electrical System
~5min read
1special tools
Specifications
Specification
Ignition System
Ignition Coil
| Item | Specification |
| Rated Voltage (V) | 12 |
| Operating Voltage (V) | 5 - 16 |
| Item | Specification | |||||
| Engine Speed (rpm) | 1000 | 2000 MY | 3000 | 4000 | 5000 | 6000 |
| Delay time (ms) | 3,82 | 2,61 | 2,27 | 1,93 | 1,79 | 1,6 |
| Secondary Winding Voltage (kV) | 32 ↑ | 32 ↑ | 31 ↑ | 30 ↑ | 29 ↑ | 27 ↑ |
Spark Plug
| Item | Specification |
| Type | SILKR6C10E |
| Gap | 0.9 - 1.0 mm (0.0354–0.0394 in.) |
| Electrode Material | Iridium |
Condenser
| Item | Specification |
| Capacitance (μF) | 0.47 [1 kHz] |
| Insulation Resistance (MΩ) | 1000 [500 V DC/1 min] |
Charging System
Generator
▷ 13.5 V, 90 A
| Item | Specification |
| Rated Voltage | 13.5 V, 90 A |
| Operating Speed | 1000–18,000 rpm |
| Voltage Regulator | Built-in IC regulator type |
| Regulator set voltage (internal mode) | 14.55 ± 0.3 V |
| Connector | 3-pin (C, FR, L) |
▷ 13.5 V, 130 A
| Item | Specification |
| Rated Voltage | 13.5 V, 130 A |
| Operating Speed | 1000–18,000 rpm |
| Voltage Regulator | Built-in IC regulator type |
| Regulator set voltage (internal mode) | 14.55 ± 0.3 V |
| Connector | 3-pin (C, FR, L) |
| Pulley Type | OAP |
Battery
▷ AGM60L-DIN
| Item | Specification |
| Capacity [20h/5h] (Ah) | 60/48 |
| Cold Cranking Amps (A) | 640 (SAE) / 640 (EN) |
| Reserve Capacity (min.) | 100 |
Starting System
Starter Motor
▷12 V, 1.2 kW: ISG only
| Item | Specification | |
| Rated Voltage | 12 V, 1.2 kW | |
| Number of Gear Teeth | 13 | |
| Performance [No Load, 11.5 V] |
Amperes | Max. 117 A |
| Speed | Min. 3200 rpm | |
▷ 12 V, 0.9 kW: Non-ISG
| Item | Specification | |
| Rated Voltage | 12 V, 0.9 kW | |
| Number of Gear Teeth | 11 | |
| Performance [No Load, 11.5 V] |
Amperes | Max. 85 A |
| Speed | Min. 3300 rpm | |
Tightening torque
| Item | N·m | kgf·m | lbf·ft |
| Ignition coil mounting bolt | 9,8 - 11,8 | 1,0 - 1,2 | 7,2 - 8,7 |
| Spark Plug | 14,7 - 24,5 | 1,5 - 2,5 | 10,9 - 18,1 |
| Condenser Mounting Nut/Bolt | 9,8 - 11,8 | 1,0 - 1,2 | 7,2 - 8,7 |
| Generator upper mounting bolt | 19,6 - 26,5 | 2,0 - 2,7 | 14,5 - 19,5 |
| Generator lower mounting bolt | 29,4 - 41,2 | 3,0 - 4,2 | 21,7 - 30,4 |
| Generator Bracket Mounting Bolt | 19,6 - 26,5 | 2,0 - 2,7 | 14,5 - 19,5 |
| Battery Positive (+) Terminal Nut | 7,8 - 9,8 | 0,8 - 1,0 | 5,2 - 8,7 |
| Battery Negative (-) Terminal Nut | 3,9 - 5,9 | 0,4 - 0,6 | 2,9 - 4,3 |
| Battery mounting bracket bolt | 8,8 - 13,7 | 0,9 - 1,4 | 6,5 - 10,1 |
| Battery Tray Mounting Bolt | 8,8 - 13,7 | 0,9 - 1,4 | 6,5 - 10,1 |
| Battery Sensor Cable Mounting Bolt | 10,8 - 13,7 | 1,1 - 1,4 | 7,9 - 10,1 |
| Starter motor bolt | 49,0 - 63,7 | 5,0 - 6,5 | 36,1 - 47,0 |
Special Service Tools
Special Service Tools
| Tool Name/Number | Illustration | Description |
| Generator Pulley Removal Wrench 09373-27000 |
![]() |
Used to remove/install the alternator pulley |
Test yourself
A quick Kia Rio YB quiz: every answer comes with an explanation and a link to the manual page.
Was this page helpful?
