Rear Bumper
Exploded View

| Rear bumper side bracket LH | Rear bumper bracket RH | Rear bumper bracket LH | |||
Hands free sensor bracket (with hands free sensor models) |
Double-sided tape [t: 1.2 mm (0.047 in)] (with hands free sensor models) |
Rear bumper fascia | |||
| Rear bumper molding LH | Rear bumper finisher upper | Rear bumper finisher lower | |||
| Rear bumper molding RH | Rear bumper energy absorber | Rear bumper side stay RH | |||
| Rear bumper side bracket RH | Rear bumper stay A RH | Rear bumper stay B RH | |||
| Rear bumper stay B LH | Rear bumper stay A LH | Rear bumper side stay LH | |||
| Grommet | U nut | Bumper clip (with hands free sensor models) |
|||
| : Pawl | |||||
| : Always replace after every disassembly. | |||||
Removal and Installation
REMOVAL
Remove rear combination lamp. Refer to Removal and Installation.
Remove fixing clips
and screws
.

Remove mounting bolts
.

Remove fixing screws
and mounting bolts
.

Remove fixing screws
.

Apply protective tapes (A) on the part to protect it from damage.

Pull rear bumper fascia side toward the vehicle side to disengage the fitting of rear bumper side bracket and rear bumper fascia side according to the numerical order 1→2 as shown by the arrows in the figure.

| : Pawl |
Disconnect rear sonar sensor harness connector.
Disconnect rear side radar harness connector.
Remove rear bumper fascia assembly.
Remove the following parts after removing rear bumper fascia assembly.
Rear sonar sensor. Refer to SONAR SENSOR (REAR) : Removal & Installation.
Rear side radar. Refer to Removal and Installation.
Rear reflex reflector. Refer to Removal and Installation.
Hands free control unit and hands free sensors. Refer to Removal and Installation.
Bumper clips
Hands free sensor bracket
Rear bumper molding (LH and RH)
U nuts
Rear bumper bracket (LH and RH)
Grommets
Rear bumper finisher upper
Rear bumper finisher lower
Remove rear bumper energy absorber.
Remove mounting bolts, and then remove rear bumper stay A (LH and RH).
Remove mounting bolts, and then remove rear bumper stay B (LH and RH).
Remove mounting nuts, and then remove rear bumper side stay (LH and RH).
Remove rear bumper side bracket (LH and RH) fixing screws.
Disengage fixing pawls, and then remove rear bumper side bracket (LH and RH).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Inspection
SIDE RADAR IRRADIATION AREA
For side radar irradiation area, refer to the figure below.


Rear bumper fascia 
Side radar irradiation area 
Reference point (R end) C 115 mm
(4.53 in) (vertical line)D 70 mm
(2.76 in) (vertical line)E 215 mm
(8.46 in) (horizontal line)F 105 mm
(4.13 in) (vertical line)G 150 mm
(5.91 in) (horizontal line)H 70 mm
(2.76 in) (reference dimension)The dimensions are along the bumper fascia surface between each reference point.
Repairs in the side radar irradiation area may affect side radar performance. Carefully check the dimensions noted under the diagram.
REPAIR AND MENDING OF IRRADIATION AREA OF SIDE RADAR
Do not leave cracks, scratches and deformations in the side radar irradiation area.
Side radar performance may be affected by the repair of irradiation area of bumper. Carefully follow these instructions when repairing the bumper of a vehicle equipped with side radars.
Only one layer of color base coat may be applied and recoating is not allowed.
Use only body exterior paint colors approved for this model.
After applying color base paint inside the radar irradiation area, perform side radar alignment, even if bumper is not removed/reinstalled. Refer to Work Procedure. Clear painting Allowed (with conditions)Clear paint must be applied uniformly with only one layer inside the irradiation area. (No clear paint fading-out or recoating inside the area is allowed.)
After applying clear paint inside the radar irradiation area, perform side radar alignment, even if bumper is not removed/reinstalled. Refer to Work Procedure. 5 Removal of dust from surface to be painted by polishing, buffing, and base treatment before coating. Allowed -
For details of each instruction, refer to followings.
Installation of sticker, accessories, aluminum tape and wrapping film, etc.
Do not install sticker, accessories, aluminum tape and wrapping tape, etc. to side radar irradiation area. (Including transparent one)
Coating and wax, etc.
It is possible to apply coating and wax to side radar irradiation area.
Surface treatment at the start of the work can be applied.
Repair of cuts, holes, cracks, scratches and deformations.
The repair inside radar irradiation area is prohibited. Be sure to perform new rear bumper replacement. Refer to Removal and Installation.
Cannot be repaired


Side radar 
Irradiation area 
Existing paint film 
Bumper fascia plastic Paint repair
Putty application: Prohibited
Radar irradiation area cannot be repaired by applying putty. (Both partial applications are prohibited)
Color base painting: Allowed (with conditions)
To remove all existing paint films inside radar irradiation area by using #800 sandpaper.
If removing existing paint films causes scratches on the surface, perform replacement with a new bumper.
Color base (including plastic primer and primer surfacer) painting can be performed only once inside radar irradiation area and recoating is not allowed. (Definition of once is until the color base coat is dyed, not the times of sprays.)
When applying primer tinted sealer, etc., use the product which is recommended by paint supplier to improve the hiding of color base and reduce color base coat thickness.
When spray mist may stick on the reverse side of the bumper fascia, conduct to perform masking on the reverse side of the bumper to prevent spray mist adhesion.
Only the body exterior colors adopted for this model can be painted.
To use the paint suppliers, products which are approved by Nissan. Please contact each paint supplier accordingly for more information.
Step 1 : Before repair
Can be performed


Side radar 
Irradiation area 
Existing paint film 
Bumper fascia plastic Step 2 : After removing existing paint film
Can be performed


Side radar 
Irradiation area 
Existing paint film 
Bumper fascia plastic Step 3 : After color base and clear painting are performed.
Can be performed


Side radar 
Irradiation area 
Existing paint film 
Bumper fascia plastic 
Clear paint film 
Color base paint film
Conditions that color base painting cannot be performed:
Painting on existing paint films inside irradiation area is not allowed. (Both block painting and fade-out painting are prohibited.)
Cannot be performed


Side radar 
Irradiation area 
Clear paint film 
Color base paint film 
Existing paint film *1 
Bumper fascia plastic *1 : Painting on remaining paint films is not allowed.
Color base recoating is not allowed.
Cannot be performed


Side radar 
Irradiation area 
Clear paint film 
Color base paint film 
Bumper fascia plastic
Clear painting: Allowed (with conditions)
Clear painting can be performed only once inside radar irradiation area, on existing new vehicle paint films (including newly painted bumper for replacement). Definition of once is until the color coat is formed, not the times of sprays.
Conditions that clear painting can be performed:
When color base painting area (plastic primer, putty, primer surfacer, pearl base, color clear base and under clear, etc.) does not cover the irradiation area and clear painting is uniformly performed.
Can be performed


Side radar 
Irradiation area 
Clear paint film 
Color base paint film 
Existing new vehicle paint films 
Bumper fascia plastic When clear painting is uniformly performed inside the irradiation area. (The whole part is painted.)
Can be performed


Side radar 
Irradiation area 
Clear paint film 
Existing new vehicle paint films 
Bumper fascia plastic
Conditions that clear painting cannot be performed:
When clear painting is not uniformly performed inside the irradiation area. (Clear paint fade-out is prohibited.)
Cannot be performed


Side radar 
Irradiation area 
Clear paint film 
Color base paint film 
Existing new vehicle paint films 
Bumper fascia plastic When clear paint recoating is performed inside the irradiation area.
Cannot be performed


Side radar 
Irradiation area 
Clear paint film 
Existing new vehicle paint films 
Bumper fascia plastic
Polishing on paint surface
Polishing is allowed (including removing dust on the paint surface, gloss improvement, base treatment before coating, etc.).