Transaxle & transmission 6MT: RS6F94R

Control linkage

In this manual: Transaxle & transmission 6MT: RS6F94R
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~6min read

Exploded View

1. Bracket

1. Bracket
2. Shifter cable
3. Selector lever
4. Shifter lever A
5. Tapping bolt
6. Cable mounting bracket 7. Selector cable
8. Grommet
9. M/T shift selector assembly 10. Shifter lever
11. Shifter lever knob

disassembly.: Always replace after every
disassembly.

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
Removal and Installation: N·m (kg-m, in-lb)


Removal and Installation

REMOVAL

1. Shift the shifter lever to the neutral position. 2. Remove air cleaner case. Refer to EM-26, "Removal and Installation" (MR16DDT) or EM-280, "Removal and Installation" (K9K).

3. Remove bracket (1), as per the following procedure.

a. Disconnect clips (A) from bracket.: Vehicle front


a. Disconnect clips (A) from bracket. b. Remove bolts (B) from bracket.

c. Remove bracket.

4. Pull out and disconnect the each cable from the shifter lever A and the selector lever, using a suitable remover.

5. While pressing the lock of the selector cable in the direction of

5. While pressing the lock of the selector cable in the direction of the arrow shown in the figure, remove the selector cable from the cable mounting bracket. 6. While pressing the lock of the shifter cable in the direction of the arrow shown in the figure, remove the shifter cable from the cable mounting bracket. 7. Remove cable mounting bracket from transaxle case. 8. Pull the shifter lever knob upward to remove. 9. Remove center console assembly. Refer to IP-23, "Removal and Installation".

10. Pull out and disconnect the shifter cable from the pin of the M/T shift selector assembly, using a suitable remover.

11. Pull up the stopper (A) of the selector cable in the direction of

11. Pull up the stopper (A) of the selector cable in the direction of the arrow as shown in the figure.

12. Pull out and disconnect the selector cable from the pin of the M/ T shift selector assembly, using a suitable remover.

13. While pressing the lock of the selector cable in the direction of

13. While pressing the lock of the selector cable in the direction of the arrow shown in the figure, remove the selector cable from the M/T shift selector assembly. 14. While pressing the lock of the shifter cable in the direction of the arrow shown in the figure, remove the shifter cable from the M/T shift selector assembly. 15. Remove the M/T shift selector assembly. 16. Remove three way catalyst and heat plate. (MR16DDT) Refer to EX-6, "Removal and Installation". 17. Remove diesel particulate filter assembly and heat plate. (K9K) Refer to EX-17, "Removal and Installation".

18. Remove the bracket from the vehicle.

19. Disengage the pawls (A) of the grommet (1), and pull downwards

19. Disengage the pawls (A) of the grommet (1), and pull downwards to remove.

20. Remove the shifter cable and selector cable from the vehicle.

INSTALLATION

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:
• Install each cable without causing interference with other parts, a 120 mm (4.72 in)-or-less bend, and a 180-degrees-or-more twist. • Install boot of each cable without causing interference with other parts and a 90-degrees-or-more twist. • Fit boot of to center console assembly the groove on shifter lever knob.

• To install the shifter lever knob, press it into the shifter lever.

CAUTION:
• Never reuse shifter lever knob. • Be careful with orientation of shifter lever knob.

• Tapping work for tapping bolts is not applied to new transaxle case. Do not perform tapping by other than screwing tapping bolts because tapping is formed by screwing tapping bolts into transaxle case.

• Insert the each cable until it reaches the cable mounting bracket and M/T shift selector assembly. • Insert the each cable until it reaches the shifter lever A and the selector lever. • Shift the shifter lever to the neutral position. • Install the shifter cable (1) and the selector cable (2) to the bracket (3) as shown in the figure.
Install the selector cable (the M/T shift selector assembly side), as per the

Install the selector cable (the M/T shift selector assembly side), as per the following procedure.

When M/T shift selector assembly is replaced: 1. Install the selector cable to the M/T shift selector assembly. 2. Shift the shifter lever to the neutral position.

3. Install the lever stopper (A) to the M/T shift selector assembly as shown in the figure.

CAUTION:
Selector cable cannot be adjusted accurately without using the lever stopper.

4. Check that the shifter lever does not move in the direction of the select. If it moves, repeat step 3.

5. Insert the stopper (A) until it reaches the selector cable.

5. Insert the stopper (A) until it reaches the selector cable. 6. Remove the lever stopper from the M/T shift selector assembly.

7. Shift the shifter lever to each gear position to check that there are no bindings. If any, repeat step 3.

When M/T shift selector assembly is not replaced:

When M/T shift selector assembly is not replaced: 1. Install the selector cable to the M/T shift selector assembly. 2. Shift the shifter lever to the 4th gear position.

3. Adjust the length “L” between the stopper (A) and the lever to the standard value.

Length “L” : 3.51 – 4.11 mm (0.1382 – 0.1618 in)

4. Insert the stopper (A) until it reaches the selector cable.

4. Insert the stopper (A) until it reaches the selector cable.

5. Shift the shifter lever to each gear position to check that there are no bindings. If any, repeat step 3.

Inspection

Inspection

INSPECTION AFTER INSTALLATION

Shifter Lever Knob
Check that the shifter lever knob is installed in the right position.

Shifter Cable and Selector Cable • Pull each cable in the removal direction to check that it dose not disconnect from the cable mounting bracket. • Pull each cable in the removal direction to check that it dose not disconnect from the M/T shift selector assembly.

• Pull grommet in the removal direction to check that it dose not disconnect from the vehicle.

M/T Shift Selector Assembly and Shifter Lever • Check that there is no tangle, hook, abnormal sound, looseness, and interference when the shifter lever is moved to each position. If there is a malfunction, then repair or replace the malfunctioning part. • Check that the shifter lever smoothly returns to the neutral position after moving the lever from 1st to 2nd gear and moving hands off the lever. If there is a malfunction, then repair or replace the malfunctioning part.

• Check that the shifter lever smoothly returns to the neutral position after moving the lever from 5th to 6th gear and moving hands off the lever. If there is a malfunction, then repair or replace the malfunctioning part.