Engine bucking
Description
CHART 9: ENGINE BUCKING
Diagnosis Procedure
1.CHECK ECM POWER SUPPLY AND GROUND CIRCUITCheck ECM power supply and ground circuit. Refer to EC-885, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace harness or connector.
2.CHECK WIRING HARNESSVisually check the condition of the engine wiring harness.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.CHECK ACCELERATOR PEDAL POSITION SENSORCheck the accelerator pedal position sensor. Refer to EC-1001, "Component Inspection".
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace.
4.CHECK CLUTCH PEDAL POSITION SWITCHCheck clutch pedal position switch.
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair or replace.
5.CHECK VEHICLE SPEED SIGNALCheck the following component.
• ???ABS actuator and electric unit (control unit)??? [Refer to BRC-24, "CONSULT-III Function". (Without ESP), BRC-131, "CONSULT-III Function". (With ESP)] • Combination meter (Refer to MWI-23, "CONSULT-III Function".) Is the inspection result normal? YES >> GO TO 6.
NO >> Repair or replace.
6.CHECK CAN COMMUNICATIONPerform trouble diagnosis on the CAN communication line using CONSULT-III. Refer to LAN-31, "CAN COMMUNICATION SYSTEM : CAN Communication Signal Chart".
Is the inspection result normal? YES >> GO TO 7.
NO >> Repair or replace harness or connector.
7.CHECK AIR INTAKE SYSTEMCheck air intake system. Refer to EM-280, "Removal and Installation".
Is the inspection result normal? YES >> GO TO 8.
NO >> Repair or replace air intake system.
8.CHECK ELECTRIC THROTTLE CONTROL ACTUATORCheck electric throttle control actuator. Refer to EC-909, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair or replace.
9.CHECK MASS AIR FLOW SENSORCheck mass air flow sensor. Refer to EC-902, "Component Inspection".
Is the inspection result normal? YES >> GO TO 10.
NO >> Repair or replace.
10.CHECK LOW PRESSURE CIRCUITPerform the TEST 1: LOW PRESSURE CIRCUIT CHECK. Refer to EC-867, "Work Procedure (TEST 1: Low Pressure Fuel Supply System Check)".
>> GO TO 11.
11.CHECK INTERNAL FUEL TRANSFER PUMPPerform the TEST 2: INTERNAL FUEL TRANSFER PUMP CHECK. Refer to EC-868, "Work Procedure (TEST 2: Internal Fuel Transfer Pump Check)".
>> GO TO 12.
12.CHECK HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE)Perform the TEST 3: HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE). Refer to EC-868, "Work Procedure [TEST 3: High Pressure Supply Pump (Pressure Control Valve) Check]".
>> GO TO 13.
13.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)Perform the TEST 4: HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE). Refer to EC- 869, "Work Procedure [TEST 4: High Pressure Supply Pump (Volumetric Control Valve) Check]".
>> GO TO 14.
14.CHECK RAIL HIGH PRESSURE CONTROL CIRCUITPerform the TEST 5: RAIL HIGH PRESSURE CONTROL CIRCUIT CHECK. Refer to EC-871, "Work Procedure (TEST 5: Rail High Pressure Regulation Check)".
>> GO TO 15.
15.CHECK MAJOR LEAK IN FUEL INJECTOR/FUEL INJECTORS OPENPerform the TEST 6: MAJOR LEAK IN FUEL INJECTOR/FUEL INJECTORS OPEN. Refer to EC-876, "Work Procedure (TEST 6: Fuel Injectors Leak Check)".
>> GO TO 16.
16.CHECK INCORRECT FUEL INJECTION QUANTITYPerform the TEST 7: INCORRECT FUEL INJECTION QUANTITY. Refer to EC-877, "Work Procedure (TEST 7: Fuel Injection Quantity Check)".
>> INSPECTION END