Engine does not start or starts with difficulty
Description
CHART 2: ENGINE DOES NOT START OR STARTS WITH DIFFICULTY
Diagnosis Procedure
1.CHECK FUELCheck that the fuel reservoir is correctly filled and with the right fuel.
>> GO TO 2.
2.CHECK BATTERYCheck the battery. Refer to PG-124, "Removal and Installation".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace battery. Refer to PG-124, "Removal and Installation".
3.CHECK STARTER MOTORCheck the starter and starter control relay. Refer to STR-8, "STARTING SYSTEM (WITH INTELLIGENT KEY) : System Description", STR-9, "STARTING SYSTEM (WITHOUT INTELLIGENT KEY) : System Description".
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace starter motor or starter control relay.
4.CHECK ECM RELAYCheck the ECM relay. Refer to EC-976, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 5.
NO >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation" (With intelligent key system), PCS-63, "Removal and Installation" (With intelligent key system).
5.CHECK ECM POWER SUPPLY AND GROUND CIRCUITCheck ECM power supply and ground circuit. Refer to EC-885, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 6.
NO >> Repair or replace harness or connector.
6.CHECK WIRING HARNESSVisually check the condition of the engine wiring harness.
Is the inspection result normal? YES >> GO TO 7.
NO >> Repair or replace harness or connector.
7.CHECK CAMSHAFT POSITION SENSORCheck the camshaft position sensor. Refer to EC-935, "Component Inspection".
Is the inspection result normal? YES >> GO TO 8.
NO >> Repair or replace.
8.CHECK CAMSHAFTCheck the camshaft. Refer to EC-935, "Component Inspection".
Is the inspection result normal? YES >> GO TO 9.
NO >> Replace camshaft.
9.CHECK AIR INTAKE SYSTEMCheck air intake system. Refer to EM-280, "Removal and Installation".
Is the inspection result normal? YES >> GO TO 10.
NO >> Repair or replace air intake system. Refer to EM-280, "Removal and Installation".
10.CHECK ELECTRIC THROTTLE CONTROL ACTUATORCheck electric throttle control actuator. Refer to EC-909, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 11.
NO >> Repair or replace.
11.CHECK LOW PRESSURE CIRCUITPerform the TEST 1: LOW PRESSURE CIRCUIT CHECK. Refer to EC-867, "Work Procedure (TEST 1: Low Pressure Fuel Supply System Check)".
>> GO TO 12.
12.CHECK INTERNAL FUEL TRANSFER PUMPPerform the TEST 2: INTERNAL FUEL TRANSFER PUMP CHECK. Refer to EC-868, "Work Procedure (TEST 2: Internal Fuel Transfer Pump Check)".
>> GO TO 13.
13.CHECK HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE)Perform the TEST 3: HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE). Refer to EC-868, "Work Procedure [TEST 3: High Pressure Supply Pump (Pressure Control Valve) Check]".
>> GO TO 14.
14.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)Perform the TEST 4: HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE). Refer to EC- 869, "Work Procedure [TEST 4: High Pressure Supply Pump (Volumetric Control Valve) Check]".
>> GO TO 15.
15.CHECK RAIL HIGH PRESSURE CONTROL CIRCUITPerform the TEST 5: RAIL HIGH PRESSURE CONTROL CIRCUIT CHECK. Refer to EC-871, "Work Procedure (TEST 5: Rail High Pressure Regulation Check)".
>> GO TO 16.
16.CHECK MAJOR LEAK IN FUEL INJECTORS/FUEL INJECTORS OPENPerform the TEST 6: MAJOR LEAK IN FUEL INJECTOR/FUEL INJECTORS OPEN. Refer to EC-876, "Work Procedure (TEST 6: Fuel Injectors Leak Check)".
>> GO TO 17.
17.CHECK INCORRECT FUEL INJECTION QUANTITYPerform the TEST 7: INCORRECT FUEL INJECTION QUANTITY. Refer to EC-877, "Work Procedure (TEST 7: Fuel Injection Quantity Check)".
>> INSPECTION END