Transaxle & transmissioN CVT: RE0F11A

P0705 transmission range switch A

In this manual: Transaxle & transmissioN CVT: RE0F11A
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~5min read

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION PROCEDURE

CAUTION:
Be careful of the driving speed

.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION 1. Start the engine.

2. Maintain the following conditions.

Accelerator pedal position : 0.0/8 Brake pedal : Depressed
Vehicle speed : 0 km/h

3. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for 10 seconds or more.)
4. Check the first trip DTC.

Is “P0705” detected? YES >> Go to TM-394, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK TCM INPUT SIGNALS

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON. 2. Select “Data Monitor” in “TRANSMISSION”. 3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, “P POSITION SW” and “L POSITION SW”.

4. Shift the selector lever through entire positions from “P” to “L” and check ON/OFF of each monitor item.

Without CONSULT-III.

1. Turn the ignition switch OFF.Without CONSULT-III.


1. Turn the ignition switch OFF. 2. Disconnect the TCM connector. 3. Turn ignition switch ON.

4. Shift the selector lever from “P” to “L” and check the voltage between the TCM harness connector terminal and the ground.

Is the check result normal?

Is the check result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power voltage.)]>>GO TO 2. NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power voltage.)]>>GO TO 4. NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power voltage.)]>>GO TO 6. NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power voltage.)]>>GO TO 8.

NO-5 [“L POSITION SW” is “ON” when selector is not in “L” position. (Or connector terminal 2 is at power voltage.)]>>GO TO 10.

2.CHECK D POSITION SW CIRCUIT (PART 1) 1. Turn the ignition switch OFF. 2. Disconnect the TCM connector.

3. Check the continuity between the TCM harness connector terminals.

Is the check result normal?

Is the check result normal? YES >> GO TO 3.

NO >> Repair or replace the malfunctioning parts.

3.CHECK D POSITION SW CIRCUIT (PART 2) 1. Disconnect the transmission position switch connector. 2. Turn ignition switch ON.

3. Check the voltage between the TCM harness connector and ground.

Is the check result normal?

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace the malfunctioning parts.

4.CHECK N POSITION SW CIRCUIT (PART 1) 1. Turn the ignition switch OFF. 2. Disconnect the TCM connector.

3. Check the continuity between the TCM harness connector terminals.

Is the check result normal?

Is the check result normal? YES >> GO TO 5.

NO >> Repair or replace the malfunctioning parts.

5.CHECK N POSITION SW CIRCUIT (PART 2) 1. Disconnect the transmission position switch connector. 2. Turn ignition switch ON.

3. Check the voltage between the TCM harness connector and ground.

Is the check result normal?

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace the malfunctioning parts.

6.CHECK P POSITION SW CIRCUIT (PART 1) 1. Turn the ignition switch OFF. 2. Disconnect the TCM connector.

3. Check the continuity between the TCM harness connector terminals.

Is the check result normal?

Is the check result normal? YES >> GO TO 7.

NO >> Repair or replace the malfunctioning parts.

7.CHECK P POSITION SW CIRCUIT (PART 2) 1. Disconnect the transmission position switch connector. 2. Turn ignition switch ON.

3. Check the voltage between the TCM harness connector and ground.

Is the check result normal?

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace the malfunctioning parts.

8.CHECK R POSITION SW CIRCUIT (PART1) 1. Turn the ignition switch OFF. 2. Disconnect the TCM connector.

3. Check the continuity between the TCM harness connector terminals

Is the check result normal?

Is the check result normal? YES >> GO TO 9.

NO >> Repair or replace the malfunctioning parts.

9.CHECK R POSITION SW CIRCUIT (PART 2) 1. Disconnect the transmission position switch connector. 2. Turn ignition switch ON.

3. Check the voltage between the TCM harness connector and ground.

Is the check result normal?

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace the malfunctioning parts.

10.CHECK 1: L POSITION SWITCH CIRCUIT (PART 1) 1. Turn the ignition switch OFF. 2. Disconnect the TCM connector.

3. Check the continuity between the TCM harness connector terminals.

Is the check result normal?

Is the check result normal? YES >> GO TO 11.

NO >> Repair or replace the malfunctioning parts.

11.CHECK 2: L POSITION SWITCH CIRCUIT (PART 2) 1. Disconnect the transmission position switch connector. 2. Turn ignition switch ON.

3. Check the voltage between the TCM harness connector and ground.

Is the check result normal?

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace the malfunctioning parts.

12.CHECK TRANSMISSION RANGE SWITCH

Check the transmission range switch. Refer to TM-398, "Component Inspection (Transmission Range Switch)".

Is the check result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace the malfunctioning parts.

Component Inspection (Transmission Range Switch)

1.CHECK TRANSMISSION RANGE SWITCH

Check the continuity between the transmission range switch connector terminals.


Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END

NO >> There is a malfunction of the transmission range switch. Replace the transaxle assembly. Refer to TM-508, "Removal and Installation".