Transaxle & transmissioN CVT: RE0F11A

Shift lock system

In this manual: Transaxle & transmissioN CVT: RE0F11A
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~5min read

Component Function Check

1.CHECK SHIFT LOCK OPERATION (PART 1) 1. Turn ignition switch ON. 2. Shift the selector lever to “P” position.

3. Attempt to shift the selector lever to any other than position with the brake pedal released.

Can the selector lever be shifted to any other position? YES >> Go to TM-471, "Diagnosis Procedure".

NO >> GO TO 2.

2.CHECK SHIFT LOCK OPERATION (PART 2)

Attempt to shift the selector lever to any other than position with the brake pedal depressed.

Can the selector lever be shifted to any other position? YES >> INSPECTION END

NO >> Go to TM-471, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK POWER SOURCE (PART 1) 1. Turn ignition switch OFF. 2. Disconnect stop lamp switch connector 3. Turn ignition switch ON.

4. Check the voltage between the stop lamp switch harness connector terminal and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 2.

NO >> GO TO 9.

2.CHECK STOP LAMP SWITCH (PART 1)

Check stop lamp switch. Refer to TM-474, "Component Inspection (Stop Lamp Switch)".

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 10.

3.CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)

1. Disconnect CVT shift selector connector 2. Check the continuity between the stop lamp switch harness connector terminal and the CVT shift selector harness connector terminal.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace the malfunctioning parts.

4.CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)

Check the continuity between the stop lamp switch harness connector terminal and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace the malfunctioning parts.

5.CHCK GROUND CIRCUIT

Check the continuity between the CVT shift selector harness connector terminal and ground.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace the malfunctioning parts.

6.CHECK PART POSITION SWITCH 1. Disconnect park position switch connector.

2. Check park position switch. Refer to TM-473, "Component Inspection (Park Position Switch)".

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace the malfunctioning parts.

7.CHECK SHIFT LOCK SOLENOID 1. Disconnect shift lock solenoid connector.

2. Check shift lock solenoid. Refer to TM-473, "Component Inspection (Shift Lock Solenoid)".

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace the malfunctioning parts.

8.CHECK CVT SHIFT SELECTOR HARNESS

Check CVT shift selector harness. Refer to TM-473, "Component Inspection (CVT Shift Selector Harness)".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace the malfunctioning parts.

9.DETECT MALFUNCTIONING ITEM Check the following items: • Open or short circuit of the harness between ignition switch and stop lamp switch connector. Refer to PG-15, "Wiring Diagram - IGNITION POWER SUPPLY -".

• Ignition switch
• 10A fuse [No.3, fuse block (J/B)]. Refer to PG-22, "Fuse, Connector and Terminal Arrangement".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace the malfunctioning parts.

10.CHECK INSTALLATION POSITION OF STOP LAMP SWITCH

Adjust stop lamp switch position. Refer to BR-9, "Inspection and Adjustment" (LHD) or BR-77, "Inspection and Adjustment" (RHD).

>> GO TO 11.

11.CHECK STOP LAMP SWITCH (PART 2)

Check stop lamp switch. Refer to TM-474, "Component Inspection (Stop Lamp Switch)".

Is the inspection result normal? YES >> INSPECTION END

NO >> Repair or replace the malfunctioning parts.

Component Inspection (Shift Lock Solenoid)

1.CHECK SHIFT LOCK SOLENOID

Apply voltage to terminals of shift lock solenoid connector and check that shift lock solenoid is activated.

CAUTION:
• Connect the fuse between the terminals when applying the voltage.

• Never cause shorting between terminals.

Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace the shift lock unit. Refer to TM-482, "Disassembly and Assembly".

Component Inspection (Park Position Switch)

1.CHECK PARK POSITION SWITCH

Check the continuity between park position switch connector terminals.

CAUTION:
• Connect the fuse between the terminals when applying the voltage.

• Never cause shorting between terminals.

Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace the park position switch. Refer to TM-482, "Disassembly and Assembly".

Component Inspection (CVT Shift Selector Harness)

1.CHECK CVT SHIFT SELECTOR HARNESS (PART 1)

Check the continuity between the CVT shift selector harness connector terminal and the shift lock solenoid harness connector terminal.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace the CVT shift selector harness. Refer to TM-482, "Disassembly and Assembly".

2.CHECK CVT SHIFT SELECTOR HARNESS (PART 2)

Check the continuity between the shift lock solenoid harness connector terminal and the park position switch harness connector terminal.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace the CVT shift selector harness. Refer to TM-482, "Disassembly and Assembly".

3.CHECK CVT SHIFT SELECTOR HARNESS (PART 3)

Check the continuity between the park switch harness connector terminal and the CVT shift selector harness connector terminal

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace the CVT shift selector harness. Refer to TM-482, "Disassembly and Assembly".

4.CHECK CVT SHIFT SELECTOR HARNESS (PART 4)

Check harness cladding CVT shift selector harness for damage.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace the CVT shift selector harness. Refer to TM-482, "Disassembly and Assembly".

Component Inspection (Stop Lamp Switch)

1.CHECK STOP LAMP SWITCH

Check the continuity between the stop lamp switch connector terminals.

Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace stop lamp switch. Refer to BR-20, "Exploded View" (LHD) or BR-88, "Exploded View" (RHD).