Front Lower Suspension Arm
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
*B |
for Gasoline Model |
*1 |
FRONT FENDER APRON SEAL LH |
*2 |
FRONT FLOOR COVER LH |
*3 |
FRONT WHEEL OPENING EXTENSION PAD LH |
*4 |
FRONT WHEEL OPENING EXTENSION PAD RH |
*5 |
NO. 1 ENGINE UNDER COVER |
*6 |
NO. 2 ENGINE UNDER COVER ASSEMBLY |
*7 |
REAR ENGINE UNDER COVER LH |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY |
*2 |
FRONT LOWER ARM BUSHING STOPPER |
*3 |
FRONT FRAME ASSEMBLY |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- |
- |
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
(a) Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly.
(b) Install the front lower No. 1 suspension arm sub-assembly to the front frame assembly with the 3 bolts and nut in the order shown in the illustration. Torque: Bolt (1), (2) : 200 N·m {2039 kgf·cm, 148 ft·lbf} Bolt (3) : 135 N·m {1377 kgf·cm, 100 ft·lbf} NOTICE: Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured. |
![]() |
(c) Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.
Torque:
92 N·m {938 kgf·cm, 68 ft·lbf}
2. INSTALL FRONT FENDER APRON SEAL LH
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
3. INSTALL FRONT FLOOR COVER LH
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
4. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (for HV Model)
Click here ![]()
5. INSTALL REAR ENGINE UNDER COVER LH (for Gasoline Model)
Click here ![]()
6. INSTALL NO. 1 ENGINE UNDER COVER
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
7. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
8. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
9. INSTALL FRONT WHEEL
Click here ![]()
10. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
Click here ![]()
11. PERFORM INITIALIZATION
for HV Model:
|
|
Parking Assist Monitor System |
for Initialization: for Calibration: |
Panoramic View Monitor System |
for Initialization for Calibration: |
|
Click here |
Parking Assist Monitor System |
for Initialization: for Calibration: |
Panoramic View Monitor System |
for Initialization: for Calibration: |
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front lower No. 1 suspension arm sub-assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Front wheel alignment adjustment |
|
|
|
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement.) |
|
|
|
Rear television camera assembly optical axis adjustment (Back camera position setting) |
Parking Assist Monitor System |
for Initialization: for Calibration: |
|
|
Panoramic View Monitor System |
for Initialization: for Calibration: |
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Front wheel alignment adjustment |
Perform system variant learning and acceleration sensor zero point calibration. |
|
|
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement.) |
|
|
|
Rear television camera assembly optical axis adjustment (Back camera position setting) |
Parking Assist Monitor System |
for Initialization: for Calibration: |
|
|
Panoramic View Monitor System |
for Initialization: for Calibration: |
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE FRONT WHEEL
Click here ![]()
2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
3. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
4. REMOVE NO. 1 ENGINE UNDER COVER
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
5. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (for HV Model)
Click here ![]()
6. REMOVE REAR ENGINE UNDER COVER LH (for Gasoline Model)
Click here ![]()
7. REMOVE FRONT FLOOR COVER LH
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
8. REMOVE FRONT FENDER APRON SEAL LH
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
9. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
(a) Remove the bolt and 2 nuts and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly. |
![]() |
(b) Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly from the front frame assembly. NOTICE: Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured. |
![]() |
(c) Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly.






