Tire Pressure Warning Receiver
Components
COMPONENTS
ILLUSTRATION
*1 |
TIRE PRESSURE WARNING ECU AND RECEIVER |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL TIRE PRESSURE WARNING ECU AND RECEIVER
NOTICE:
- Do not drop the tire pressure warning ECU and receiver, strike it with tools or subject it to impact.
- If the tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.
(a) Connect the connector.
(b) Engage the 2 guides and install the tire pressure warning ECU and receiver with the bolt.
Torque:
8,3 N·m {85 kgf·cm, 73 in·lbf}
2. INSTALL ROOF SIDE INNER GARNISH RH
Click here ![]()
3. REGISTER TRANSMITTER ID
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
4. INSPECT TIRE PRESSURE WARNING SYSTEM
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
5. PERFORM INITIALIZATION
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
6. PERFORM DIAGNOSTIC SYSTEM CHECK
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
7. INSPECT SRS WARNING LIGHT
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tire pressure warning ECU and receiver removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)Replacement Part or Procedure | Necessary Procedures | Effects/Inoperative when not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Tire pressure warning ECU and receiver |
|
|
for Registration for Initialization |
Replacement Part or Procedure | Necessary Procedures | Effects/Inoperative when not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Tire pressure warning ECU and receiver |
|
|
for Registration for Initialization |
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
NOTICE:
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.
for HV Model: Click here ![]()
for Gasoline Model: Click here ![]()
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE ROOF SIDE INNER GARNISH RH
Click here ![]()
3. REMOVE TIRE PRESSURE WARNING ECU AND RECEIVER
NOTICE:
- Do not drop the tire pressure warning ECU and receiver, strike it with tools or subject it to impact.
- If the tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.
(a) Remove the bolt. |
![]() |
(b) Disengage the 2 guides.
(c) Disconnect the connector to remove the tire pressure warning ECU and receiver.


