Tire And Wheel System
How To Proceed With Troubleshooting
PROCEDURE
CHECK TIRE AND WHEEL SYSTEM
| DIAGNOSIS OF IRREGULAR TIRE WEAR | GO TO STEP 11 |
|
TIGHTEN WHEEL NUTS
Click here ![]()
|
INSPECT TIRES
Click here ![]()
| NG | GO TO STEP 10 |
|
INSPECT AND/OR ADJUST WHEEL BALANCE
Click here ![]()
|
INSPECT FRONT AXLE HUB BEARING LOOSENESS AND AXLE HUB RUNOUT
Click here ![]()
| NG | GO TO STEP 9 |
|
INSPECT REAR AXLE HUB BEARING LOOSENESS AND AXLE HUB RUNOUT
Click here ![]()
| NG | GO TO STEP 8 |
|
PERFORM ROAD TEST
| NEXT | RETURN VEHICLE TO CUSTOMER |
REPAIR REAR AXLE HUB BEARING LOOSENESS AND AXLE HUB RUNOUT
Click here ![]()
| NEXT | GO TO STEP 7 |
REPAIR FRONT AXLE HUB BEARING LOOSENESS AND AXLE HUB RUNOUT
Click here ![]()
| NEXT | GO TO STEP 6 |
REPAIR OR REPLACE TIRE(S)
| NEXT | GO TO STEP 4 |
INSPECT TIRES
Click here ![]()
|
REPAIR OR REPLACE TIRE(S)
|
INSPECT AND/OR ADJUST FRONT WHEEL ALIGNMENT
Click here ![]()
|
INSPECT AND/OR ADJUST REAR WHEEL ALIGNMENT
Click here ![]()
|
PERFORM ROAD TEST
| NEXT | RETURN VEHICLE TO CUSTOMER |
Inspection
INSPECTION
PROCEDURE
1. INSPECT TIRES
(a) Inspect the tires for wear and proper inflation pressure.
Cold Tire Inflation Pressure:
Tire Size | Cold Tire Inflation Pressure |
|
|---|---|---|
Front | Rear |
|
215/55R17 94V 235/45R18 94V 235/40R19 92V |
240 kPa (2.4 kgf/cm2, 35 psi) |
240 kPa (2.4 kgf/cm2, 35 psi) |
Cold Tire Inflation Pressure (for Compact Spare Tire):
Tire Size | Cold Tire Inflation Pressure |
|---|---|
T155/70D17 110M |
420 kPa (4.2 kgf/cm2, 60 psi) |
(1) Perform initialization.
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
(2) Tire pressure adjustment method when warm:
- Turn the engine switch (for Gasoline Model) or power switch (for HV Model) off.
- Connect the Techstream to the DLC3.
- Turn the engine switch (for Gasoline Model) or power switch (for HV Model) on (IG).
- Turn the Techstream on.
- Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
- Adjust the tire pressure so that the displayed value is equal to the set pressure.
- Perform initialization and check that initialization completes.
for Gasoline Model: Click here

for HV Model: Click here

- Check and record the value of the Data List item "Temperature in Tire". (Ts)
- Check and record the ambient temperature during tire pressure adjustment. (Tm)
- Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)
HINT:
Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P
P = (Specified Pressure) + (Ts - Tm)
- Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".
(b) Using a dial indicator, check the runout of the tires. Maximum Tire Runout: 1.4 mm (0.0551 in.) HINT: Measure the runout with the wheel assembly removed from the vehicle. |
![]() |
2. ROTATE TIRES
(a) Remove the wheel assembly.
Click here ![]()
(b) Rotate the tires as shown in the illustration.
![]() |
Front |
(c) Install the wheel assembly.
Click here ![]()
(d) Perform initialization.
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
3. INSPECT AND ADJUST WHEEL BALANCE
(a) Inspect and adjust the off-the-car balance. Maximum Wheel Imbalance: 8.0 g (0.0176 lb) NOTICE:
HINT:
|
|
4. INSPECT FRONT AXLE HUB BEARING
Click here ![]()
5. INSPECT REAR AXLE HUB BEARING
Click here ![]()


