Suspension Control Ecu
Components
COMPONENTS
ILLUSTRATION
*1 |
BAGGAGE HOLDER NET |
*2 |
SPARE WHEEL COVER ASSEMBLY |
ILLUSTRATION
*1 |
LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 |
LUGGAGE COMPARTMENT TRIM INNER COVER RH |
*3 |
NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
*4 |
REAR FLOOR FINISH PLATE |
ILLUSTRATION
*1 |
ABSORBER CONTROL ECU |
*2 |
CONNECTOR |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL ABSORBER CONTROL ECU
(a) Install the absorber control ECU with the 2 nuts.
Torque:
7,5 N·m {76 kgf·cm, 66 in·lbf}
NOTICE:
- Avoid any impact to the absorber control ECU.
- Do not drop the absorber control ECU. If it is dropped, replace it with a new one.
(b) Connect the 2 connectors to the absorber control ECU.
2. INSTALL LUGGAGE COMPARTMENT TRIM INNER COVER RH
Click here ![]()
3. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD
Click here ![]()
4. INSTALL REAR FLOOR FINISH PLATE
Click here ![]()
5. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Click here ![]()
6. INSTALL BAGGAGE HOLDER NET
Click here ![]()
7. INSTALL SPARE WHEEL COVER ASSEMBLY
Click here ![]()
8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Click here ![]()
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here ![]()
9. PERFORM TEST MODE PROCEDURE
NOTICE:
After replacing the absorber control ECU, it is necessary to perform registration of vehicle identification information. Vehicle identification information is automatically acquired when the system enters test mode.
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during absorber control ECU removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Replacement of the absorber control ECU |
Registration of vehicle identification information |
|
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here ![]()
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here ![]()
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here ![]()
3. REMOVE SPARE WHEEL COVER ASSEMBLY
Click here ![]()
4. REMOVE BAGGAGE HOLDER NET
Click here ![]()
5. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Click here ![]()
6. REMOVE REAR FLOOR FINISH PLATE
Click here ![]()
7. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD
Click here ![]()
8. REMOVE LUGGAGE COMPARTMENT TRIM INNER COVER RH
Click here ![]()
9. REMOVE ABSORBER CONTROL ECU
(a) Disconnect the 2 connectors from the absorber control ECU. |
![]() |
(b) Remove the 2 nuts and absorber control ECU.
NOTICE:
- Avoid any impact to the absorber control ECU.
- Do not drop the absorber control ECU. If it is dropped, replace it with a new one.


