Rear Lower Arm
Components
COMPONENTS
ILLUSTRATION
*A |
for Gasoline Model |
*B |
for RH Side |
*C |
for LH Side |
- |
- |
*1 |
NO. 1 FLOOR UNDER COVER |
*2 |
NO. 2 FLOOR UNDER COVER |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
REAR COIL SPRING |
*2 |
REAR LOWER COIL SPRING INSULATOR |
*3 |
REAR NO. 2 SUSPENSION ARM ASSEMBLY |
*4 |
REAR STABILIZER LINK ASSEMBLY |
*5 |
REAR STABILIZER BAR |
*6 |
REAR SUSPENSION TOE ADJUST CAM SUB-ASSEMBLY |
*7 |
NO. 2 CAMBER ADJUST CAM |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- |
- |
ILLUSTRATION
*1 |
REAR NO. 1 SUSPENSION ARM ASSEMBLY |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- |
- |
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY
(a) Temporarily install the rear No. 1 suspension arm assembly to the rear axle carrier sub-assembly and rear suspension member sub-assembly with the 2 bolts and 2 nuts.
NOTICE:
- Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
- Insert the bolt with the threaded end facing the rear of the vehicle.
2. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY
(a) Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member sub-assembly with the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and nut.
NOTICE:
- Insert the rear suspension toe adjust cam sub-assembly from the rear of the vehicle.
- When tightening the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.
3. INSTALL REAR LOWER COIL SPRING INSULATOR
Click here ![]()
4. INSTALL REAR COIL SPRING
Click here ![]()
5. STABILIZE SUSPENSION
Click here ![]()
6. INSTALL REAR STABILIZER LINK ASSEMBLY
Click here ![]()
7. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY
(a) Install the rear No. 1 suspension arm assembly with the 2 bolts. Torque: 73 N·m {744 kgf·cm, 54 ft·lbf} NOTICE: Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured. |
![]() |
8. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY
(a) Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt. Torque: 73 N·m {744 kgf·cm, 54 ft·lbf} NOTICE: Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured. |
![]() |
9. INSTALL NO. 1 FLOOR UNDER COVER (for Gasoline Model)
(a) for RH Side:
Click here ![]()
10. INSTALL NO. 2 FLOOR UNDER COVER (for Gasoline Model)
(a) for LH Side:
Click here ![]()
11. INSTALL REAR WHEEL
Click here ![]()
12. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY
(a) Lower the vehicle to the ground.
(b) Bounce the vehicle up and down at the corners to stabilize the rear suspension.
(c) Align the matchmarks on the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly. |
|
(d) Fully tighten the nut.
Torque:
100 N·m {1020 kgf·cm, 74 ft·lbf}
NOTICE:
- Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.
- Make sure that the vehicle is unloaded when fully tightening the nut.
13. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
Click here ![]()
14. PERFORM INITIALIZATION
for Gasoline Model:
|
|
Parking Assist Monitor System |
|
Panoramic View Monitor System |
|
|
|
Parking Assist Monitor System |
|
Panoramic View Monitor System |
|
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension arm assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Rear wheel alignment adjustment |
Perform system variant learning and acceleration sensor zero point calibration. |
|
|
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement.) |
|
|
|
Rear television camera assembly optical axis adjustment (Back camera position setting) |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Rear wheel alignment adjustment |
|
|
|
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement.) |
|
|
|
Rear television camera assembly optical axis adjustment (Back camera position setting) |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE REAR WHEEL
Click here ![]()
2. REMOVE NO. 2 FLOOR UNDER COVER (for Gasoline Model)
(a) for LH Side:
Click here ![]()
3. REMOVE NO. 1 FLOOR UNDER COVER (for Gasoline Model)
(a) for RH Side:
Click here ![]()
4. REMOVE REAR STABILIZER LINK ASSEMBLY
Click here ![]()
5. REMOVE REAR COIL SPRING
Click here ![]()
6. REMOVE REAR LOWER COIL SPRING INSULATOR
Click here ![]()
7. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY
(a) Remove the nut, No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and rear No. 2 suspension arm assembly. NOTICE: Hold the rear suspension toe adjust cam sub-assembly while rotating the nut. |
![]() |
8. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY
(a) Remove the 2 bolts, 2 nuts and rear No. 1 suspension arm assembly from the rear axle carrier sub-assembly and rear suspension member sub-assembly. NOTICE: Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured. |
![]() |








