ECU Terminals
ECU TERMINALS
INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY (TMMT Made)
(a) Disconnect the F72 connector from the air conditioning amplifier assembly.
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Tester Connection | Wire Color | Terminal Description | Ignition switch position | Specified Condition |
|---|---|---|---|---|
F72-5 (IG+) - F72-29 (GND) |
B - W-B |
Power supply (IG) |
Ignition Switch in ON position |
11 à 14 V |
Ignition Switch in OFF position |
Below 1 V |
|||
F72-1 (B) - F72-29 (GND) |
V - W-B |
Battery power supply |
Always |
11 à 14 V |
F72-29 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
(c) Reconnect the F72 connector to the air conditioning amplifier assembly.
(d) Measure the voltage and check the pulses according to the value(s) in the table below.
Tester Connection | Wire Color | Terminal Description | Ignition switch position | Specified Condition |
|---|---|---|---|---|
F72-26 (RDFG) - F72-29 (GND) |
P - W-B |
Rear Defogger Signal |
Ignition switch ON, rear defogger switch OFF |
11 à 14 V |
Ignition switch ON, rear defogger switch ON |
Below 1 V |
|||
F72-3 (LIN1) - F72-29 (GND) |
L - W-B |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
If the result is not as specified, there may be a malfunction in the A/C amplifier assembly.
INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY (TMC Made)
(a) Disconnect the F139 connector from the air conditioning amplifier assembly.
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Tester Connection | Wire Color | Terminal Description | Ignition switch position | Specified Condition |
|---|---|---|---|---|
F139-2 (IG+) - F139-4 (GND) |
B - W-B |
Power supply (IG) |
Ignition Switch in ON position |
11 à 14 V |
Ignition Switch in OFF position |
Below 1 V |
|||
F139-1 (B) - F139-4 (GND) |
V - W-B |
Battery power supply |
Always |
11 à 14 V |
F139-4 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
(c) Reconnect the F139 connector to the air conditioning amplifier assembly.
(d) Measure the voltage and check the pulses according to the value(s) in the table below.
Tester Connection | Wire Color | Terminal Description | Ignition switch position | Specified Condition |
|---|---|---|---|---|
F139-5 (RDFG) - F139-4 (GND) |
P - W-B |
Rear Defogger Signal |
Ignition switch ON, rear defogger switch OFF |
11 à 14 V |
Ignition switch ON, rear defogger switch ON |
Below 1 V |
|||
F139-14 (LIN1) - F139-4 (GND) |
BE - W-B |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
If the result is not as specified, there may be a malfunction in the A/C amplifier assembly.
CHECK AIR CONDITIONING CONTROL ASSY
(a) Check the pulses according to the value(s) shown in the table below.
Tester Connection | Wire Color | Terminal Description | Ignition switch position | Specified Condition |
|---|---|---|---|---|
F61-2 (LIN1) - F61-16 (GND) |
L - W-B*1 BE - W-B*2 |
LIN communication line |
Ignition Switch in ON position |
Pulse generation |
- *1: Manufactured by TMMT
- *2: Manufactured by TMC
If the result is not as specified, there may be a malfunction in the air conditioning control assembly.