ECU Terminals
ECU TERMINALS
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
*A |
Main Body ECU (Multiplex Network Body ECU) with 1 connector |
- |
- |
*A |
Main Body ECU (Multiplex Network Body ECU) with 2 connectors |
- |
- |
(a) Disconnect the connectors from the instrument panel junction block assembly and the main body ECU (multiplex network body ECU).
Click here
![]()
(b) Reconnect the connectors to the instrument panel junction block assy.
(c) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
MB-31 (BECU) - Body ground |
- |
Battery power supply |
Always |
11 à 14 V |
MB-32 (IG) - Body ground |
- |
Ignition power supply (IG signal) |
Ignition switch ON → OFF |
11 to 14 V → Below 1 V |
MB-30 (ACC) - Body ground |
- |
Ignition power supply (ACC signal) |
Ignition switch ACC → OFF |
11 to 14 V → Below 1 V |
MB-11 (GND1) - Body ground |
- |
Ground |
Always |
Below 1 Ω |
MB-2 (RCTY) - Body ground |
- |
Rear RH door courtesy light switch input |
Rear LH door closed (OFF) |
10 kΩ minimum |
Rear LH door open (ON) |
Below 1 Ω |
|||
MB-13 (LCTY) - Body ground |
- |
Rear LH door courtesy light switch input |
Rear RH door closed (OFF) |
10 kΩ minimum |
Rear RH door open (ON) |
Below 1 Ω |
CHECK COMBINATION METER ASSEMBLY
(a) Disconnect the connector from the combination meter assembly F4.
(b) Measure the voltage and resistance according to the value(s) specified in the table below.
HINT:
Measure the values at the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
F4-40 (B) - Body Ground |
SB - Body ground |
Battery power supply |
Always |
11 à 14 V |
F4-39 (IG+) - Body Ground |
P - Body ground |
Ignition power supply |
Ignition Switch in OFF position |
Below 1 V |
Ignition Switch in ON position |
11 à 14 V |
|||
F4-21 (ET) - Body Ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
F4-10 (MSD) - Body Ground |
V - Body ground |
Rear LH Seat Belt Buckle Switch Signal |
Rear LH seat belt buckled |
10 kΩ minimum |
Rear left seat belt unbuckled |
Below 1 Ω |
|||
F4-11 (MSTI) - Body Ground |
BE - Body ground |
Rear Center Seat Belt Buckle Switch Signal |
Rear center seat belt buckled |
10 kΩ minimum |
Rear center seat belt unbuckled |
Below 1 Ω |
|||
F4-13 (MSFM) - Body Ground |
R - Body ground |
Rear RH Seat Belt Buckle Switch Signal |
Rear RH seat belt buckled |
10 kΩ minimum |
Rear RH seat belt unbuckled |
Below 1 Ω |
|||
F4-3 (RRMT) - Body Ground |
W - Body Ground |
Rear RH Seat Belt Reminder Light Signal |
Ignition switch ON, rear RH seat belt unbuckled within 34 seconds after rear door is closed |
Below 1 V |
Ignition switch ON, rear RH seat belt buckled within 34 seconds after rear door is closed |
11 à 14 V |
|||
F4-2 (RCMT) - Body Ground |
V - Body ground |
Rear Center Seat Belt Reminder Light Signal |
Ignition switch ON, rear center seat belt unbuckled within 34 seconds after rear door is closed |
Below 1 V |
Ignition switch ON, rear center seat belt buckled within 34 seconds after rear door is closed |
11 à 14 V |
|||
F4-1 (RLMT) - Body Ground |
L - Body ground |
Rear LH Seat Belt Reminder Light Signal |
Ignition switch ON, rear LH seat belt unbuckled within 34 seconds after rear door is closed |
Below 1 V |
Ignition switch ON, rear LH seat belt buckled within 34 seconds after rear door is closed |
11 à 14 V |
CHECK AIRBAG SENSOR ASSEMBLY
Terminal No. | Terminal Symbol | Destination |
|---|---|---|
M1-10 |
LBE+ |
Front LH Seat Belt Inner Belt Assembly |
M1-18 |
LBE- |
Front LH Seat Belt Inner Belt Assembly |
CHECK OCCUPANT DETECTION ECU
(a) Measure the voltage and check the pulses according to the specified value(s) in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
Y6-10 (GND) - Body Ground |
W-B - Body ground |
Ground |
Always |
Below 1 V |
Y6-6 (IG2) - Y6-10 (GND) |
B - W-B |
Power source |
Ignition Switch in ON position |
11 à 14 V |
Y6-9 (BGND) - Y6-10 (GND) |
P - W-B |
Front Passenger Buckle Switch Ground |
Always |
Below 1 V |
Y6-7 (BSW) - Y6-9 (BGND) |
G - P |
Front Passenger Buckle Switch Signal |
Always |
Pulse generation |
Y5-1 (SVC1) - Y5-5 (SGD1) |
R - G |
Front LH Occupant Classification Sensor Power Supply |
Ignition Switch in ON position |
11 à 14 V |
Y5-2 (SVC3) - Y5-6 (SGD3) |
GR - W |
Rear LH Occupant Classification Sensor Power Supply |
Ignition Switch in ON position |
11 à 14 V |
Y5-3 (SIG1) - Y5-5 (SGD1) |
P - G |
Front LH Occupant Classification Sensor Signal |
Ignition Switch in ON position |
Pulse generation |
Y5-4 (SIG3) - Y5-6 (SGD3) |
SB - W |
Rear Left Occupant Classification Sensor Signal |
Ignition Switch in ON position |
Pulse generation |
Y5-5 (SGD1) - Y6-10 (GND) |
G - W-B |
Front Left Occupant Classification Sensor Ground |
Always |
Below 1 V |
Y5-6 (SGD3) - Y6-10 (GND) |
W - W-B |
Rear Left Occupant Classification Sensor Ground |
Always |
Below 1 V |