Inspection On Vehicle
INSPECTION ON VEHICLE
PROCEDURE
1. CHECK DRIVER SIDE SEAT BELT REMINDER LIGHT
HINT:
The seat belt warning light on the combination meter assembly is used for the driver seat and the front passenger seat.
(a) Turn the ignition switch to ON.
(b) Make sure that the seat belt reminder light flashes on the combination meter assembly when the driver seat belt is not buckled.
(c) Raise the vehicle using a swing arm type lift.
Click here![]()
(d) Start the engine.
(e) If the driver seat belt is not buckled and the vehicle is driven at a speed of approximately 20 km/h or more, make sure that the seat belt warning light on the combination meter assembly flashes at 1.2 second intervals for 30 seconds.
Then, make sure that the seat belt reminder light on the combination meter assembly flashes at 0.4 second intervals.
(f) Make sure that the seat belt reminder light on the combination meter assembly turns off when the driver seat belt is buckled.
2. CHECK FRONT PASSENGER SEAT BELT REMINDER LIGHT
HINT:
The seat belt warning light on the combination meter assembly is used for the driver seat and the front passenger seat.
(a) Place a 20 kg (44.0 lb.) weight on the front passenger seat.
NOTICE:
Place the weight on the seat cushion and allow it to contact the seatback.
(b) Buckle the driver seat belt.
(c) Turn the ignition switch to ON.
(d) Make sure that the seat belt warning light on the combination meter assembly flashes when the front passenger seat belt is not buckled.
(e) Raise the vehicle using a swing arm type lift.
Click here![]()
(f) Start the engine.
(g) When the front passenger seat is occupied, the front passenger seat belt is not buckled and the vehicle is driven at a speed of approximately 20 km/h or more, make sure that the seat belt reminder light on the combination meter assembly flashes at 1.2 second intervals for 30 seconds.
Then, make sure that the seat belt reminder light on the combination meter assembly flashes at 0.4 second intervals.
(h) Make sure that the seat belt reminder light on the combination meter assembly turns off when the front passenger seat belt is buckled.
3. CHECK REAR SEAT BELT REMINDER LIGHT
(a) Check the status of the rear seat belt warning light on the instrument cluster assembly: (1) Turn the ignition switch OFF. (2) Open and close one of the rear doors. (3) Turn the ignition switch to the ON position. (4) When a rear seat belt is not buckled, make sure that the rear seat belt warning light on the instrument cluster assembly is on. (5) After 34 seconds, check that the rear seat belt warning light on the instrument cluster assembly turns off. (6) When any of the rear seat belts changes from buckled to unbuckled, make sure that the rear seat belt warning light on the instrument cluster assembly turns on. |
|
4. CHECK SEAT BELT WARNING BUZZER
HINT:
The seat belt warning buzzer can be customized. Make sure that this function is enabled.
Click here![]()
(a) Place a 20 kg (44.0 lb.) weight on the front passenger seat.
NOTICE:
Place the weight on the seat cushion and allow it to contact the seatback.
(b) Raise the vehicle using a swing arm type lift.
Click here![]()
(c) Start the engine.
(d) Check that the seat belt reminder buzzer of the instrument cluster assembly sounds at 1.2-second intervals for 30 seconds.
(e) After the seat belt reminder buzzer has sounded at 1.2-second intervals for 30 seconds, check that the seat belt reminder buzzer of the instrument cluster assembly sounds at 0.4-second intervals for 90 seconds.
(f) Check that the seat belt reminder buzzer on the instrument cluster assembly stops 2 minutes after it started sounding at 1.2-second intervals.
(g) Once the buzzer has stopped, turn the ignition switch OFF, then restart the engine. Drive the vehicle at approximately 20 km/h or more while the driver, front passenger or rear seat belt is not fastened, and check that the buzzer sounds again.
(h) Once the buzzer stops, fasten the driver, front passenger or rear seat belt. Drive the vehicle at approximately 20 km/h or more, unfasten the driver, front passenger or any rear seat belt, then check that the buzzer sounds again.
(i) Once the buzzer has stopped, stop the vehicle, move the shift lever to R, then to D. Drive the vehicle at approximately 20 km/h or more, then check that the buzzer sounds again.
