Doors / Back Door

Disassembly

~9min read

DISASSEMBLY

PRECAUTION / NOTICE / HINT

The procedures required (adjustment, calibration, initialization or registration), which must be performed after parts have been removed and installed, or replaced during rear door removal/installation, are shown below.

Procedures Required After Replacement / Removal / Installation of Parts

Replaced Part or Performed Procedure

Required Procedure

Effects / Inoperative Function When Necessary Procedure Not Performed

Link

Disconnect the cable from the negative (-) battery terminal.

Initialize Back Door Lock

Door Lock Control System

Memorize Steering Angle Neutral Point

Lane Departure Alert System (with Steering Control)

Pre-Collision System

  • Rear Door Window Regulator Assembly
  • Rear Door Window Glass Subassembly
  • Rear Door Window Slider

Initialize Power Window Control System

  • Automatic Open and Close Function
  • Anti-Pinch Function
  • Anti-Pinch Function Operation
  • Remote Control Function
  • Key-Linked Function
  • Function Linked to Remote Control Transmitter
  • Keyless Operation
  • Power Window Open Warning Function

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. PRECAUTIONS

NOTICE:

After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

Click here

2. DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

Click here

NOTICE:

When the cable has been disconnected, some systems must be reset after the cable is reconnected.

Click here

3. REMOVE REAR DOOR REAR FRAME BRACKET

(a) Release the claws and clip to remove the rear door opening trim support as shown in the illustration.

Remove in this direction

4. REMOVE REAR DOOR INSIDE HANDLE GARNISH CLIP

(a) Using a moulding remover A, release the claws to remove the rear door inside handle garnish clip as shown in the illustration.

Remove in this direction

5. REMOVE REAR POWER WINDOW SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

(a) Release the claws, clips and guides as shown in the illustration.

Remove in this direction

(b) Disconnect the connector to remove the rear power window switch assembly with rear door armrest base upper panel.

6. REMOVE THE REAR DOOR TRIM PANEL SUB-ASSEMBLY

(a) Remove the 3 screws.

(b) Remove the 2 screws.

Place hands here

Remove in this direction

(c) Release the clips and guide as shown in the illustration.

(d) Release the claws as shown in the illustration.

Remove in this direction

(e) Release the guides to disconnect the rear door inside locking cable assembly and the rear door remote control locking cable assembly to remove the rear door garnish sub-assembly as shown in the illustration.

*1

Rear Door Inside Locking Cable Assembly

*2

Rear Door Remote Control Locking Cable Assembly

Remove in this direction

7. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

(a) Release the claw and guides to remove the front door inside handle sub-assembly.

8. REMOVE REAR DOOR BELTLINE REAR SEAL

(a) Remove the rear door beltline rear seal.

9. REMOVE REAR DOOR WINDOW INSIDE WEATHERSTRIP

(a) Remove the rear door window inside weatherstrip together with the rear door beltline seal as shown in the illustration.

Remove in this direction

10. REMOVE REAR DOOR BELTLINE SEAL

(a) Remove the rear door beltline seal from the rear door window inside weatherstrip as shown in the illustration.

Remove in this direction

11. REMOVE HOLE PLUG

(a) Remove the 2 hole plugs.

12. REMOVE NO. 2 REAR DOOR FRAME GARNISH

(a) Remove the No. 2 rear door frame garnish.

13. REMOVE REAR DOOR GARNISH BRACKET

(a) Remove the 2 screws and the rear door garnish bracket.

14. REMOVE REAR DOOR INSIDE PANEL REINFORCEMENT SUB-ASSEMBLY (with rear seat side airbag)

(a) Remove the 4 screws and the rear door inside panel reinforcement sub-assembly.

15. REMOVE REAR DOOR SERVICE HOLE COVER

(a) Remove the rear door service hole cover.

Butyl Tape

HINT:

Remove any butyl tape residue from the rear door panel.

16. REMOVE NO. 2 SEPARATION DOOR RETAINER PAD (with rear seat side airbag)

(a) Remove the 2 bolts.

Double-sided adhesive tape

(b) Remove the double-sided tape.

(c) Release the guides to remove the No. 2 separation door retainer pad.

NOTICE:

Remove any remaining double-sided tape from the rear door panel.

17. REMOVE REAR DOOR PAD (with rear seat side airbag)

(a) Remove the 2 bolts.

(b) Release the hooks to remove the rear door pad.

18. REMOVE REAR DOOR CHECK ASSEMBLY

(a) Remove the 3 bolts and the rear door check assembly.

19. REMOVE REAR DOOR MOULDING

(a) Using a clip remover, release the clip (A) and the other clips.

*a

Clip (A)

Double-sided adhesive tape

(b) Remove the double-sided tape and the rear door moulding.

NOTICE:

Remove any remaining double-sided tape from the rear door panel.

20. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY

(a) Remove the screw and the 2 bolts.

(b) Remove the rear door window rear lower frame sub-assembly from the rear door window regulator slider.

21. REMOVE REAR DOOR WINDOW SUB-ASSEMBLY

(a) Disengage the rear door window sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

NOTICE:

After removing the rear door window sub-assembly, take care not to drop it.

(b) Remove the rear door window sub-assembly as shown in the illustration.

NOTICE:

Do not damage the rear door window sub-assembly.

Remove in this direction (1)

Remove in this direction (2)

22. REMOVE REAR DOOR FRAME GARNISH

(a) Release the guides to remove the rear door frame garnish.

23. REMOVE REAR DOOR WINDOW SLIDER

(a) Remove the rear door window slider.

24. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

(a) Disconnect the connector.

*a

Temporary Bolt

(b) Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

(c) Remove the 3 bolts and the rear door window regulator assembly.

(d) Remove the temporary bolt from the rear door window regulator assembly.

25. REMOVE REAR DOOR QUARTER WINDOW GLASS

(a) Remove the rear door quarter window glass together with the rear door quarter window glass weatherstrip as shown in the illustration.

Remove in this direction

26. REMOVE REAR DOOR QUARTER WINDOW GLASS WEATHERSTRIP

(a) Remove the rear door quarter window glass weatherstrip from the rear door quarter window glass.

27. REMOVE REAR DOOR BELTLINE MOULDING ASSEMBLY

Click here

28. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

(a) Disconnect the No. 1 remote control locking cable assembly from the clips.

(b) Remove the 3 bolts.

(c) Remove the double-sided adhesive tape.

Double-sided adhesive tape

(d) As shown in the illustration, release the claws from the rear door access hole to remove the rear door outside handle assembly together with the rear door outside handle cover as a single unit.

Push in

CAUTION:

Be careful not to cut your hands or fingers on the edge of the rear door panel.

HINT:

If your hands are not suitable, use a tool such as a screwdriver with its tip wrapped in protective tape to release the claws.

(e) Release the guide to free the No. 1 rear door remote control central door lock cable assembly, then remove the rear door outside handle assembly with the rear door outside handle cover.

NOTICE:

Remove any remaining double-sided tape from the rear door panel.

29. REMOVE REAR DOOR OUTSIDE HANDLE COVER

(a) Release the clips and the guide to remove the rear door outside handle cover.

30. REMOVE REAR DOOR OUTSIDE HANDLE GASKET

(a) Remove the 2 rear door outside handle gaskets.

31. REMOVE REAR DOOR LOCK ASSEMBLY WITH MOTOR

Click here

32. REMOVE REAR DOOR DUST SEAL

(a) Remove the 3 rear door dust seals.

33. REMOVE REAR SPEAKER ASSEMBLY

Click here

34. REMOVE REAR DOOR PANEL BASE

(a) Release the claws to remove the 2 rear door panel pads.

35. REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Click here

36. REMOVE REAR DOOR OUTSIDE MOULDING

Click here

37. REMOVE REAR DOOR WINDOW FRAME UPPER MOULDING

Click here

38. REMOVE REAR DOOR WINDOW FRAME REAR MOULDING

Click here

39. REMOVE REAR DOOR OUTSIDE LOWER GARNISH MOULDING

Click here

40. REMOVE REAR DOOR OUTSIDE GARNISH MOULDING

Click here