Doors / Back Door

Adjustment

~3min read
1special tools
010203040502619N·mlb·ft
Tightening torque found on this page

ADJUSTMENT

PRECAUTION / NOTICE / HINT

*a

Centering Bolt

*b

Standard Bolt

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.
  • The centering bolts are used to install the door hinges on the vehicle body and the door. The door cannot be adjusted while the centering bolts are installed. Replace the centering bolts with standard bolts before making adjustments.
  • The specified torque for standard bolts is shown in the standard bolt table.

    Click here

PROCEDURE

1. INSPECT REAR DOOR PANEL SUB-ASSEMBLY

(a) Make sure the clearance measurements at areas "A" to "W" are within the standard ranges.

Standard clearance

Area

Measurement

Area

Measurement

A

3.3 to 6.7 mm (0.130 to 0.264 in.)

B

0.9 to 4.9 mm (0.035 to 0.193 in.)

C

3.3 to 6.7 mm (0.130 to 0.264 in.)

D

1.8 to 5.8 mm (0.071 to 0.228 in.)

E

3.3 to 6.7 mm (0.130 to 0.264 in.)

F

2.5 to 6.5 mm (0.098 to 0.256 in.)

G

3.3 to 6.7 mm (0.130 to 0.264 in.)

H

2.3 mm (0.091 in.)

I

3.3 to 7.3 mm (0.130 to 0.287 in.)

J

1.0 mm (0.039 in.)

K

2.6 to 6.6 mm (0.102 to 0.260 in.)

L

0.7 mm (0.028 in.)

M

2.6 to 5.6 mm (0.102 to 0.220 in.)

N

2.1 to 6.1 mm (0.083 to 0.240 in.)

O

3.3 to 8.3 mm (0.130 to 0.327 in.)

P

-2.5 to 2.5 mm (-0.098 to 0.098 in.)

Q

3.5 to 8.5 mm (0.138 to 0.335 in.)

R

7.5 to 11.5 mm (0.295 to 0.453 in.)

S

-2.0 to 2.0 mm (-0.079 to 0.079 in.)

T

2.9 to 5.3 mm (0.114 to 0.209 in.)

U

-1.2 to 1.2 mm (-0.047 to 0.047 in.)

V

2.4 to 6.4 mm (0.094 to 0.252 in.)

W

-2.0 to 2.0 mm (-0.079 to 0.079 in.)

-

-

2. ADJUST REAR DOOR PANEL SUB-ASSEMBLY

(a) Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

SST: 09812-00010

(b) After adjustment, tighten the 4 hinge bolts on the vehicle body.

Torque:

26 N·m {265 kgf·cm, 19 ft·lbf}

(c) Loosen the 4 hinge bolts on the door and adjust the door position.

(d) After adjustment, tighten the 4 hinge bolts on the door.

Torque:

Manufactured by TMMT:

26 N·m {265 kgf·cm, 19 ft·lbf}

Manufactured by TMC:

21 N·m {214 kgf·cm, 15 ft·lbf}

(e) Using a "TORX" T40 socket wrench, slightly loosen the 2 striker mounting screws.

(f) Using a brass bar and a hammer, tap the striker to adjust its position.

(g) Using a "TORX" T40 socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:

23 N·m {235 kgf·cm, 17 ft·lbf}