Windows

Windshield deicer does not operate

~5min read

DESCRIPTION

When the windshield deicer switch on the air conditioning control assembly is pressed, the operation signal is sent to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the DEICER relay to operate the windshield deicer system.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Check the fuses and relay for the circuits related to this system before performing the following procedure.
  • If battery voltage drops low, windshield deicer operation is disabled to give priority to power supply for the power steering system.

PROCEDURE

  1. CHECK AIR CONDITIONING SYSTEM

(a) Check the air conditioning system.

HINT:

The windshield deicer operation signal and the air conditioning operation signal are sent to the air conditioning amplifier assembly via the same communication line.

OK:

The air conditioning system operates normally.

Result:

Result

Proceed to

OK

A

NG (for TMMT manufactured)

B

NG (for TMC manufactured)

C

B

GO TO AIR CONDITIONING SYSTEM

C

GO TO AIR CONDITIONING SYSTEM

A
  1. PERFORM ACTIVE TEST USING TECHSTREAM

(a) Using Techstream, perform the Active Test.

Click here

Body Electrical > Air Conditioner > Active Test

Tester display

Item

Control Range

Diagnostic Note

Deicer Relay (Front)

Windshield Glass (Windshield Deicer)

OFF or ON

-

Body Electrical > Air Conditioner > Active Test

Deicer Relay (Front)

OK:

The windshield deicer system operates normally.

NG

GO TO STEP 4

OK
  1. REPLACE AIR CONDITIONING CONTROL ASSEMBLY

(a) Replace the air conditioning control assembly with a new or normally functioning one.

Click here

(b) Make sure the defogging system operates normally.

Click here

OK

END (AIR CONDITIONING CONTROL ASSEMBLY WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. INSPECT WIRE HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)

(a) Disconnect connectors 3F and 3A from the instrument panel junction block assembly.

*a

Front view of wire harness side connector

(to Instrument Panel Junction Block Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

3F-5 - Body ground

Always

11 à 14 V

3A-21 - Body ground

Ignition Switch in ON position

11 à 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

(a) Disconnect connector 3A from the instrument panel junction block assembly.

(b) Disconnect the F72*1 or F139*2 connector from the air conditioning amplifier assembly.

  • *1: Manufactured by TMMT
  • *2: Manufactured by TMC

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

TMMT manufactured

Tester Connection

Condition

Specified Condition

3A-18 - F72-24 (FDEF)

Always

Below 1 Ω

3A-18 or F72-24 (FDEF) - Body ground

Always

10 kΩ minimum

TMC manufactured

Tester Connection

Condition

Specified Condition

3A-18 - F139-17 (FDEF)

Always

Below 1 Ω

3A-18 or F139-17 (FDEF) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

(a) Remove the instrument panel junction block assembly.

Click here

*a

Component without wire harness connected (Instrument Panel Junction Block Assembly)

-

-

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

3F-5 - 3F-4

Battery voltage applied between terminals 3A-21 and 3A-18

Below 1 Ω

Battery voltage not applied between terminals 3A-21 and 3A-18

10 kΩ minimum

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - WINDSHIELD GLASS (WINDSHIELD DEICER))

(a) Disconnect the A64 connector from the windshield glass (windshield deicer).

(b) Disconnect the 3F connector from the instrument panel junction block.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

3F-4 - A64-1 (B)

Always

Below 1 Ω

3F-4 or A64-1 (B) - Body Ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (WINDSHIELD GLASS [WINDSHIELD DEFOGGER] - BODY GROUND)

(a) Disconnect the windshield glass (windshield defogger) connector.

*a

Front view of wire harness side connector

(to Windshield Glass [Windshield Defogger])

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A64-2 (E) - Body Ground

Always

Below 1 Ω

OK

REPLACE WINDSHIELD GLASS (WINDSHIELD DEFOGGER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR