Windows

Installation

~9min read

INSTALLATION

PROCEDURE

1. CLEAN BACK DOOR GLASS

(a) When reusing the back door glass:

(1) Using a scraper, remove any remaining adhesive residue from the rear window glass.

NOTICE:

Be careful not to damage the rear window glass.

(2) Clean the outer edges of the rear window glass using a residue-free solvent.

NOTICE:

  • Do not touch the surface of the rear window glass after cleaning it.
  • Even when using a new rear window glass, clean the glass with a residue-free solvent.

2. INSTALL BACK DOOR GLASS SPACER (for upper portion)

(a) Using a brush or sponge, apply a coat of primer G to the installation area of the new back door glass spacer.

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(b) Place the 2 new back door glass spacers on the back door glass as shown in the illustration.

*a

Back side of back door glass

*b

Ceramic notch

3. INSTALL BACK DOOR GLASS SPACER (for side)

(a) Using a brush or sponge, apply a coat of primer G to the installation area of the new back door glass spacer.

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(b) Place the 4 new back door glass spacers on the back door glass as shown in the illustration.

*a

Back side of back door glass

*b

Ceramic notch

4. INSTALL REAR WINDOW LOWER MOULDING

(a) Using a brush or sponge, apply a coat of primer G to the installation area of the new rear window lower moulding.

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(b) Place the new rear window lower moulding on the back door glass as shown in the illustration.

Standard dimension:

Area

Measurement

a

10.3 mm (0.406 in.)

b

18.5 mm (0.728 in.)

c

15.1 mm (0.594 in.)

*a

Back side of back door glass

5. INSTALL REAR WINDOW SPACER NO. 2

(a) Using a brush or sponge, apply a coat of primer G to the installation area of the new rear window spacer No. 2.

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(b) Place the new rear window spacer No. 2 on the back door glass as shown in the illustration.

*a

Back side of back door glass

*b

Ceramic notch

6. INSTALL REAR WINDOW SPACER NO. 1

HINT:

Perform the same procedure as for the rear window spacer No. 2.

7. INSTALL REAR WINDOW OUTSIDE MOULDING LH

(a) Using a brush or sponge, apply a coat of primer G to the installation area of the new rear window outside moulding LH.

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(b) Place the new rear window outside moulding LH on the back door glass as shown in the illustration.

Standard dimension:

Area

Measurement

a

9.9 mm (0.390 in.)

*a

Back side of back door glass

8. INSTALL REAR WINDOW OUTSIDE MOULDING RH

HINT:

Perform the same procedure as for the left side.

9. INSTALL BACK DOOR GLASS

(a) Clean and correct the contact surface of the vehicle body.

(1) On the contact surface of the vehicle body, use a knife to remove excess adhesive as shown in the illustration.

NOTICE:

Leave as much adhesive as possible on the vehicle body.

(b) Preliminary installation procedures for back door glass:

(1) Attach the suction cups to the back door glass.

(2) Temporarily place the back door glass on the vehicle body and position it so that the clearance between the body and the top and side edges of the back door glass is even.

(c) Position the back door glass.

(1) Using suction cups, place the back door glass in the correct position.

(2) Check that the entire contact surface of the back door glass edge is perfectly even.

(3) Align the alignment marks on the back door glass and the back door panel.

NOTICE:

Make sure rear window spacers No. 1 and No. 2 are correctly engaged with the back door panel.

(4) Remove the back door glass.

*a

Alignment Mark

(d) Using a brush, apply a coat of primer M to the installation surfaces on the back door panel.

NOTICE:

  • Do not apply M primer to the adhesive.
  • Do not apply too much M primer.
  • Allow the M primer coat to dry for at least 3 minutes.
  • Discard unused M primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the M primer before it dries using a clean piece of cloth.

(e) Using a brush or sponge, apply a coat of G primer to the tape application area.

*a

Back side of back door glass

*b

Adhesive Center Position

*c

Ceramic notch

-

-

G primer

-

-

Standard dimension:

Area

Measurement

a

7.0 mm (0.276 in) minimum

b

15.3 mm (0.602 in)

c

7.0 mm (0.276 in) minimum

d

18.5 mm (0.728 in.)

e

7.0 mm (0.276 in) minimum

f

12.3 mm (0.484 in)

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

  • Apply G primer to the ceramic frit.
  • If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(f) Apply adhesive to the back door glass.

Adhesive:

Genuine Toyota windshield adhesive (high modulus type) or equivalent

(1) Cut the end of the cartridge nozzle as shown in the illustration.

Standard dimension:

Area

Measurement

a

12.0 to 15.0 mm (0.472 to 0.591 in.)

b

8.0 to 11.0 mm (0.315 to 0.433 in.)

*a

Nozzle

(2) Load the cartridge into the sealer gun.

(3) Apply adhesive to the back door glass as shown in the illustration.

*a

Back side of back door glass

*b

Adhesive Center Position

*c

Ceramic notch

-

-

Adhesive

-

-

Standard dimension:

Area

Measurement

a

15.3 mm (0.602 in)

b

18.5 mm (0.728 in.)

c

12.3 mm (0.484 in)

HINT:

Apply adhesive to the ceramic frit.

(g) Install the back door glass.

(1) Using suction cups, position the back door glass so the alignment marks line up, then press gently along the edge.

NOTICE:

  • Make sure rear window spacers No. 1 and No. 2 are correctly engaged with the back door panel.
  • Check the clearance between the back door panel and the back door glass.

*a

Alignment Mark

(2) Lightly press the outer surface of the back door glass to seat it properly and engage the No. 1 rear window glass spacer and the No. 2 rear window glass spacer.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf.) minimum.

(3) Using a scraper, remove any adhesive beads or excess adhesive.

(4) Hold the back door glass in place with protective tape until the adhesive has cured.

HINT:

Follow the adhesive manufacturer's instructions or the product instructions for the minimum waiting time before the vehicle can be driven.

(h) Connect each connector and engage each clip.

10. CONNECT NO. 1 BACK DOOR CABLE

(a) Connect the 2 connectors to the back door glass.

11. INSTALL REAR COMBINATION LAMP ASSEMBLY (Bulb Type)

Click here

12. INSTALL REAR COMBINATION LAMP ASSEMBLY (LED Type)

Click here

13. INSTALL REAR WIPER MOTOR ASSEMBLY

Click here

14. CHECK FOR LEAKS

(a) Once the adhesive has hardened, apply water from the outside of the vehicle. Check for water leaks inside the cabin.

(b) If water leaks into the cabin, let the water dry and apply additional adhesive.

(c) Remove the masking tape.

15. INSTALL REAR SPOILER

Click here