Toyota Camry Quiz
Manual transmission/transaxle

Shift & select lever shaft assy (E351)

In this manual: Manual transmission/transaxle
Introduction — 61Audio & visual system — 16Automatic transmission / trans — 19Transmission revolution (ATM) — 1Shift lock system (ATM) — 1Brake — 20Clutch — 10Communication system — 4Cooling — 15Cruise control — 3Drive shaft / propeller shaft — 9Emission control — 8Engine control system — 12Engine hood/door — 7Exhaust — 3Exterior/interior trim — 14Front suspension — 9Fuel — 12Heater & air conditioner — 16Ignition — 8Instrument panel/meter — 7Intake — 7Lighting — 11Lubrication — 16Manual transmission/transaxle — 13Parking brake — 10Power steering — 7Rear suspension — 10Seat — 12Service specifications — 26Sliding roof/convertible — 4Starting & charging — 11Starting system (2AZ−FE)(From July, 2003) — 1Starting system (1MZ−FE/3MZ−FE) — 1Steering column — 6Theft deterrent & door lock — 9Tire & wheel — 4Windshield/windowglass/mirror — 5Back window glass — 1Power window control system — 1Power mirror control system — 1Inner rear view mirror assy — 1Windshield glass — 1Wiring — 1
4steps
~24min
2/5difficulty
01020304050129N·mlb·ft
Tightening torque found on this page
Done 0 of 4
1. REMOVE CONTROL SHIFT LEVER BUSH

a. Remove the control shift lever bush from the selecting bellcrank No.2.

Remove control shift lever bush Remove control shift lever bush 2. REMOVE SELECTING BELLCRANK DUST COVER No.1

a. Remove the selecting bellcrank dust cover No.1 from the selecting bellcrank No.2.

Remove selecting bellcrank dust cover No.1 Remove selecting bellcrank dust cover No.1 3. REMOVE SELECTING BELLCRANK SUPPORT SUB−ASSY

a. Remove the nut, washer and selecting bellcrank No.2 plate washer from the selecting bellcrank No.2.

b. Remove the selecting bellcrank support sub−assy from

b. Remove the selecting bellcrank support sub−assy from the selecting bell crank No.2.

4. REMOVE SELECTING BELLCRANK DUST COVER
4. REMOVE SELECTING BELLCRANK DUST COVER No.2

a. Remove the selecting bell crank dust cover No.2 from the selecting bellcrank No.2.

Remove selecting bellcrank dust cover No.2 Remove selecting bellcrank dust cover No.2 5. REMOVE SELECTING BELLCRANK No.2 BUSH

a. Remove the selecting bellcrank bush from the selecting bellcrank No.2.

Remove selecting bellcrank No.2 Bush Remove selecting bellcrank No.2 Bush 6. REMOVE SHIFT LEVER INNER No.2

a. Hold the shift & select lever on the vise through the soft jaw.

NOTICE: Do not damage the shift & select lever shaft.

b. Using a pin punch (f 5 mm), remove the shift & select lever inner slotted pin and oil baffle.

NOTICE: Do not damage the shift & select lever shaft.

c. Apply the force to the select return spring No.1 and select return spring No.2 then hold it on the vise through the soft jaw.

d. Using 2 screwdrivers and a hammer, remove the select

d. Using 2 screwdrivers and a hammer, remove the select seat snap ring from the shift & select lever shaft.

NOTICE: Do not damage the shift & select lever shaft.
7. REMOVE SELECT SPRING SEAT No.1
7. REMOVE SELECT SPRING SEAT No.1

a. Using a pin punch (ϕ 5 mm), remove the shift inner lever slotted pin from the shift & select lever shaft.

b. Remove the shift lever assy select return spring No.1 and

b. Remove the shift lever assy select return spring No.1 and select spring seat from the shift & select lever shaft.

8. REMOVE SHIFT INTER LOCK PLATE COVER
8. REMOVE SHIFT INTER LOCK PLATE COVER

a. Remove the shift inter lock plate cover from the shift inter lock plate.

Remove shift inter lock plate cover Remove shift inter lock plate cover 9. REMOVE SHIFT LEVER INNER No.1

a. Remove the shift lever inner No.1 from the shift inter lock plate.

Remove shift lever inner No.1 Remove shift lever inner No.1 10. REMOVE SELECT SPRING No.1 SEAT SHAFT SNAP RING

a. Using 2 screwdrivers and a hammer, remove the select spring No.1 seat shaft snap ring.

NOTICE: Do not damage the shaft. Remove select spring No.1 Seat shaft snap ring Remove select spring No.1 Seat shaft snap ring 11. REMOVE CONTROL SHAFT COVER OIL SEAL

a. Using a screwdriver, remove the control shaft cover oil seal from the control shaft cover.

Remove control shaft cover oil seal Remove control shaft cover oil seal 12. REMOVE CONTROL SHAFT COVER BIMETAL FORMED BUSH a. Using SST, remove the control shaft cover bimetal formed bush from the control shift cover.

SST 09319−60020

Remove control shaft cover bimetal formed bush Remove control shaft cover bimetal formed bush 13. INSTALL CONTROL SHAFT COVER BIMETAL FORMED BUSH a. Using SST and hammer, install a new control shaft cover bimetal formed bush to the control shaft cover.

SST 09950−60010 (09951−00210), 09950−70010 (09951−07100)

Oil seal drive in depth: 0 0.25 mm (0 0.010 in.) Install control shaft cover bimetal formed bush Install control shaft cover bimetal formed bush 14. INSTALL CONTROL SHAFT COVER OIL SEAL a. Using SST and hammer, install a new control shaft cover oil seal to the control shaft cover.

SST 09950−60010 (09951−00280), 09950−70010 (09951−07100)

Oil seal drive in depth: 28.5 0.50 mm (1.122 0.020 in.) Install control shaft cover oil seal Install control shaft cover oil seal 15. INSTALL SELECT SPRING No.1 SEAT SHAFT SNAP RING

a. Using a brass bar and a hammer, install the select spring No.1 seat shaft snap ring.

Install select spring No.1 Seat shaft snap ring Install select spring No.1 Seat shaft snap ring 16. INSTALL SHIFT LEVER INNER No.1

a. Install the shift lever inner No.1 to the shift inter lock plate.

Install shift lever inner No.1 Install shift lever inner No.1 17. INSTALL SHIFT INTER LOCK PLATE COVER

a. Install the shift inter lock plate cover to the shift inter lock plate.

Install shift inter lock plate cover Install shift inter lock plate cover 18. INSTALL SELECT SPRING SEAT No.1

a. Install the select spring seat No.1, select return spring No.1 and shift lever inner assy to the shift & select lever shaft.

Install select spring seat No.1 Install select spring seat No.1
  1. Hold the shift & select lever on the vise through the soft jaw.
  2. Using a pin punch (f 5 mm), install the shift lever slotted pin to the shift & select lever shaft. Clearance: −0.5 − 0.5 mm (− 0.0197 − 0.0197 in.)
    19. INSTALL SHIFT LEVER INNER No.2
19. INSTALL SHIFT LEVER INNER No.2
  1. Install shift lever inner No.2, select return spring No.2 and select return spring seat No.2 to the shift & select lever shaft.
  2. Using a brass bar and a hammer, install the select seat snap ring to the shift & select lever shaft.
Install shift lever inner No.2 Install shift lever inner No.2 c. Install the transmission oil baffle. Using a pin punch (f 5 mm) and a hammer, install the shift inner lever slotted pin to the shift & select lever shaft.Clearance: 5.8 to 6.8 mm (0.228 to 0.268 in.)
20. INSTALL SELECTING BELLCRANK No.2 BUSH
20. INSTALL SELECTING BELLCRANK No.2 BUSH

a. Coat the 2 selecting bellcrank No.2 bushes with MP grease, install it to the selecting bellcrank No.2.

Install selecting bellcrank No.2 Bush Install selecting bellcrank No.2 Bush 21. INSTALL SELECTING BELLCRANK DUST COVER No.2

a. Coat the selecting bellcrank dust cover No.2 Ωith MP grease, install it to the selecting bellcrank No.2.

Install selecting bellcrank dust cover No.2 Install selecting bellcrank dust cover No.2 22. INSTALL SELECTING BELLCRANK SUPPORT SUB−ASSY

a. Install the selecting bellcrank support sub−assy to the selecting bellcrank No.2.

b. Install the selecting bellcrank No.2 plate washer, washer
b. Install the selecting bellcrank No.2 plate washer, washer and nut.Torque: 12 N·m
23. INSTALL SELECTING BELLCRANK DUST COVER
23. INSTALL SELECTING BELLCRANK DUST COVER No.1

a. Install the selecting bellcrank dust cover No.1 to the selecting bellcrank No.2.

Install selecting bellcrank dust cover no.1 Install selecting bellcrank dust cover No.1 24. INSTALL CONTROL SHIFT LEVER BUSH

a. Install the control shift lever bush to the selecting bell crank No.2.

Install control shift lever bush Install control shift lever bush

Test yourself

A quick Toyota Camry quiz: every answer comes with an explanation and a link to the manual page.