DESCRIPTION
The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake warning light remains on:
- The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
- The brake fluid level is insufficient.
- EBD operation is not possible.
WIRING DIAGRAM
NOTICE:
- When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.
Click here 
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.
PROCEDURE
CHECK CAN COMMUNICATION SYSTEM
(a) Check if CAN communication system DTCs are output.
Click here 
Result | Proceed to |
DTCs are not output |
A |
DTCs are output |
B |
| B |
 |
INSPECT CAN COMMUNICATION SYSTEM |
| A |
 |
|
CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
(a) Check if the skid control ECU (brake actuator assembly) connector is securely connected.
OK:
The connector is securely connected.
| NG |
 |
CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY |
| OK |
 |
|
CHECK BATTERY
(a) Check the battery voltage.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
Positive (+) terminal - Negative (-) terminal |
Ignition switch off |
11 to 14 V |
| NG |
 |
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
(a) Turn the ignition switch off. |
 |
*a |
Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
|
|
(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(c) Disconnect the A57 skid control ECU (brake actuator assembly) connector.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
A57-25 (+BS) - Body ground |
Always |
11 to 14 V |
A57-6 (IG1) - Body ground |
Ignition switch ON |
11 to 14 V |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
(a) Turn the ignition switch off. |
 |
*a |
Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
A57-38 (GND1) - Body ground |
Always |
Below 1 Ω |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT) |
| OK |
 |
|
INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
(a) Turn the ignition switch off. |
 |
*a |
Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly)) |
|
|
(b) Reconnect the A57 skid control ECU (brake actuator assembly) connector.
(c) Remove the reservoir filler cap and strainer.
(d) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(e) Disconnect the A3 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.
(f) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(g) Measure the resistance according to the value(s) in the table below.
HINT:
A float is located inside the reservoir. Its position changes according to the brake fluid level.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
1 (+) - 2 (E) |
Switch off (float up) |
10 kΩ or higher |
1 (+) - 2 (E) |
Switch on (float down) |
Below 1 Ω |
HINT:
If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.
| NG |
 |
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - MASTER CYLINDER RESERVOIR SUB-ASSEMBLY)
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(b) Disconnect the J28 combination meter assembly connector.
(c) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
J28-14 (SW) - A3-1 (+) |
Always |
Below 1 Ω |
J28-14 (SW) or A3-1 (+) - Body ground |
Always |
10 kΩ or higher |
A3-2 (E) - Body ground |
Always |
Below 1 Ω |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
READ VALUE USING TECHSTREAM (BRAKE WARNING LIGHT)
(a) Reconnect the A3 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.
(b) Reconnect the J28 combination meter assembly connector.
(c) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List. ABS/VSC/TRAC
Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
Brake Warning Light |
Brake warning light |
ON or OFF |
ON: Warning light on
OFF: Warning light off |
- |
(d) Check the Techstream display condition of the brake warning light.
Result | Proceed to |
The value of Brake Warning Light is ON |
A |
The value of Brake Warning Light is OFF |
B |
| A |
 |
REPLACE BRAKE ACTUATOR ASSEMBLY |
| B |
 |
INSPECT METER / GAUGE SYSTEM |
|