Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
ABS Warning Light |
ABS warning light |
ON or OFF |
ON: Warning light on
OFF: Warning light off |
- |
Brake Warning Light |
Brake warning light |
ON or OFF |
ON: Warning light on
OFF: Warning light off |
- |
Stop Light SW |
Stop light switch assembly |
ON or OFF |
ON: Brake pedal depressed
OFF: Brake pedal released |
- |
Parking Brake SW |
Parking brake switch assembly |
ON or OFF |
ON: Parking brake applied
OFF: Parking brake released |
- |
Main Idle SW |
Main idle switch |
ON or OFF |
ON: Accelerator pedal released
OFF: Accelerator pedal depressed |
- |
Brake Pedal Load Sensing SW |
Brake Pedal Load Sensing Switch |
ON or OFF |
ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point |
- |
Gear Position |
Gear position information |
"P, N", R, 1st-10th, Fail or Not R |
Actual gear position |
- |
Shift Lever Position |
Shift lever position information |
"P, N", R, D/M, 1st-6th/B or Fail |
Actual shift lever position |
- |
Shift Information |
Shift information |
ON or OFF |
ON: During gear change
OFF: Not during gear change |
- |
Inspection Mode |
Inspection mode |
Other or Inspect |
Other: Normal mode
Inspect: Inspection mode |
- |
Number of IG ON(Inspection) |
Number of times ignition switch turned to ON after entering inspection mode |
Min.: 0, Max.: 255 |
- |
- |
Master Cylinder Sensor |
Master cylinder pressure sensor reading |
Min.: 0.00 V, Max.: 5.00 V |
Brake pedal released: 0.20 to 0.40 V |
Reading increases when brake pedal is depressed |
Deceleration Sensor |
Lateral acceleration sensor (GL1) reading |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- |
During deceleration/acceleration: Changes continuously |
Zero Point of Decele |
Memorized zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- |
- |
Deceleration Sensor2 |
Longitudinal acceleration sensor (GL2) reading |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- |
During deceleration/acceleration: Changes continuously |
Zero Point of Decele2 |
Memorized zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- |
- |
Yaw Rate Sensor |
Yaw rate sensor |
Min.: -128°/s, Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s |
- |
Zero Point of Yaw Rate |
Memorized zero value |
Min.: -128°, Max.: 127° |
- |
After completing zero point calibration: 0° |
Steering Angle Sensor |
Steering angle sensor |
Min.: -3276.8°, Max.: 3276.7° |
Turning left: Increases
Turning right: Decreases |
- |
Zero Point of Steering Angle |
Memorized zero value |
Min.: -3276.8°, Max.: 3276.7° |
- |
After steering angle sensor zero point calibration: 0° |
Lateral G |
Lateral G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- |
During turning: Changes in proportion with lateral acceleration |
Forward and Rearward G |
Forward and rearward G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- |
During acceleration/deceleration: Changes in proportion with acceleration |
Yaw Rate Value |
Yaw rate value |
Min.: -128°/s, Max.: 127°/s |
- |
During turning: Changes in proportion with yaw |
Steering Angle Value |
Steering angle value |
Min.: -3276.8°, Max.: 3276.7° |
- |
During steering operation: Changes in proportion with steering wheel rotation |
Stop Light Relay |
Stop light control relay (VSC ACC)
(STP2 terminal input) |
ON or OFF |
ON: Relay input on
OFF: Relay input off |
- |
Slip Indicator Light |
Slip indicator light |
ON or OFF |
ON: Indicator light on
OFF: Indicator light off |
- |
FR Wheel Speed |
Front wheel speed sensor RH reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
FL Wheel Speed |
Front wheel speed sensor LH reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
RR Wheel Speed |
Rear wheel speed sensor RH reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
RL Wheel Speed |
Rear wheel speed sensor LH reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
Vehicle Speed |
Maximum wheel speed sensor reading |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
FR Wheel Acceleration |
Front wheel RH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
- Displays a negative value during deceleration and a positive value during acceleration
- During deceleration/acceleration: Changes continuously
|
FL Wheel Acceleration |
Front wheel LH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
- Displays a negative value during deceleration and a positive value during acceleration
- During deceleration/acceleration: Changes continuously
|
RR Wheel Acceleration |
Rear wheel RH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
- Displays a negative value during deceleration and a positive value during acceleration
- During deceleration/acceleration: Changes continuously
|
RL Wheel Acceleration |
Rear wheel LH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
- Displays a negative value during deceleration and a positive value during acceleration
- During deceleration/acceleration: Changes continuously
|
Stop Light Relay Output |
Stop light control relay (VSC ACC)
(STPO terminal output) |
ON or OFF |
ON: Relay output on
OFF: Relay output off |
- |
FR Wheel ABS Ctrl Status |
Front wheel RH ABS control status |
ON or OFF |
ON: During control |
- |
FL Wheel ABS Ctrl Status |
Front wheel LH ABS control status |
ON or OFF |
ON: During control |
- |
RR Wheel ABS Ctrl Status |
Rear wheel RH ABS control status |
ON or OFF |
ON: During control |
- |
RL Wheel ABS Ctrl Status |
Rear wheel LH ABS control status |
ON or OFF |
ON: During control |
- |
FR Wheel EBD Ctrl Status |
Front wheel RH EBD control status |
ON or OFF |
ON: During control |
- |
FL Wheel EBD Ctrl Status |
Front wheel LH EBD control status |
ON or OFF |
ON: During control |
- |
RR Wheel EBD Ctrl Status |
Rear wheel RH EBD control status |
ON or OFF |
ON: During control |
- |
RL Wheel EBD Ctrl Status |
Rear wheel LH EBD control status |
ON or OFF |
ON: During control |
- |
BA Ctrl Status |
BA control status |
ON or OFF |
ON: During control |
- |
PBA Ctrl Status |
PBA control status |
ON or OFF |
ON: During control |
- |
TRC(TRAC) Ctrl Status |
TRAC control status |
ON or OFF |
ON: During control |
- |
TRC(TRAC) Engine Ctrl Status |
TRAC engine control status |
ON or OFF |
ON: During control |
- |
TRC(TRAC) Brake Ctrl Status |
TRAC brake control status |
ON or OFF |
ON: During control |
- |
FR Wheel VSC Ctrl Status |
Front wheel RH VSC control status |
ON or OFF |
ON: During control |
- |
FL Wheel VSC Ctrl Status |
Front wheel LH VSC control status |
ON or OFF |
ON: During control |
- |
RR Wheel VSC Ctrl Status |
Rear wheel RH VSC control status |
ON or OFF |
ON: During control |
- |
RL Wheel VSC Ctrl Status |
Rear wheel LH VSC control status |
ON or OFF |
ON: During control |
- |
Engine Revolutions |
Engine speed |
Min.: 0 rpm, Max.: 65535 rpm |
Engine stopped: 0 rpm |
When engine speed is constant: No large fluctuations |
Real Engine Torque |
Real engine torque |
Min.: -1024 Nm, Max.: 1023 N·m |
- |
- |
Accelerator Opening Angle % |
Percentage of accelerator pedal opening angle |
Min.: 0.0%, Max.: 127.5% |
Accelerator pedal released: 0.0% |
During accelerator pedal operation: Changes in proportion with the pedal movement |
Solenoid Relay |
ABS solenoid relay |
ON or OFF |
ON: ABS solenoid relay on
OFF: ABS solenoid relay off |
- |
ECB Motor Relay |
ABS motor relay |
ON or OFF |
ON: ABS motor relay on
OFF: ABS motor relay off |
- Not applicable to this vehicle
- ECB: Electronically Controlled Brake
|
TR(A)C/VSC Solenoid (SRM2) |
Master cut solenoid (SRM2) |
ON or OFF |
ON: During control |
- |
TR(A)C/VSC Solenoid (SRM1) |
Master cut solenoid (SRM1) |
ON or OFF |
ON: During control |
- |
TR(A)C/VSC Solenoid (SRC2) |
Master cut solenoid (SRC2) |
ON or OFF |
ON: During control |
- |
TR(A)C/VSC Solenoid (SRC1) |
Master cut solenoid (SRC1) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SFRH) |
ABS solenoid (SFRH) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SFRR) |
ABS solenoid (SFRR) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SFLH) |
ABS solenoid (SFLH) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SFLR) |
ABS solenoid (SFLR) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SRRH) |
ABS solenoid (SRRH) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SRRR) |
ABS solenoid (SRRR) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SRLH) |
ABS solenoid (SRLH) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SRLR) |
ABS solenoid (SRLR) |
ON or OFF |
ON: During control |
- |
EFI Communication Open |
ECM communication open detection |
Error or Normal |
Error: Momentary interruption detected
Normal: Momentary interruption not detected |
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal". |
Yaw Rate Open |
Yaw rate sensor open detection |
Error or Normal |
Error: Momentary interruption detected
Normal: Momentary interruption not detected |
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal". |
Deceleration Open |
Acceleration sensor open detection |
Error or Normal |
Error: Momentary interruption detected
Normal: Momentary interruption not detected |
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal". |
Steering Open |
Steering angle sensor open detection |
Error or Normal |
Error: Momentary interruption detected
Normal: Momentary interruption not detected |
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal". |
BS1 Voltage Value |
+BS voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- |
Changes in proportion to battery voltage |
MT Voltage Value |
Motor voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- |
Changes in proportion to battery voltage |
TRAC/VSC Off Mode |
TRAC/VSC off mode |
Normal, TRC OFF or VSC OFF |
Normal: Normal mode
TRC OFF: TRAC off mode
VSC OFF: VSC off mode |
- |
Number of DTC |
Number of DTC recorded |
Min.: 0, Max.: 255 |
- |
- |
IG Voltage Value Decreased |
+BS voltage value decrease detection |
Error or Normal |
Error: Low voltage detected
Normal: Low voltage not detected |
- After low voltage occurs, if there is no low voltage error for 1 second, it switches from "Error" to "Normal".
- Error: 9.8 V or less
|
IG Voltage Value Increased |
+BS voltage value increase detection |
Error or Normal |
Error: High voltage detected
Normal: High voltage not detected |
- After high voltage occurs, if there is no high voltage error for 1 second, it switches from "Error" to "Normal".
- Error: 17.4 V or higher
|