Vehicle Interior
Fuel Sender Open Detected (B1500)
DESCRIPTION
This DTC is output when the combination meter detects the fuel sender gauge malfunction via the CAN.
DTC Code | DTC Detection Condition | Trouble Area |
B1500 |
When combination meter detects fuel sender gauge malfunction |
- Harness or connector
- Combination meter
- Fuel sender gauge
- Fuel suction with pump and gauge tube
|
WIRING DIAGRAM
PROCEDURE
READ VALUE USING TECHSTREAM (FUEL SENDER GAUGE)
(a) Operate the Techstream according to the display and select the "Data List" (See page ). Combination Meter:
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
Fuel Level |
Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5 |
Fuel sender input value |
Unit: L |
OK:
Fuel value displayed on Techstream is almost same as needle indication
| OK |
 |
REPLACE COMBINATION METER ASSEMBLY |
| NG |
 |
|
CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND GAUGE TUBE AND BODY GROUND)
(a) Disconnect the J28 meter connector.
(b) Disconnect the R6*1 or R19*2 gauge connector.
- *1: except 3UR-FBE
- *2: for 3UR-FBE
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance: except 3UR-FBE
Tester Connection | Condition | Specified Condition |
J28-26 (L) - R6-2 |
Always |
Below 1 Ω |
J28-25 (E3) - R6-3 |
J28-24 (ES) - Body ground |
J28-26 (L) or R6-2 - Body ground |
Always |
10 kΩ or higher |
for 3UR-FBE
Tester Connection | Condition | Specified Condition |
J28-26 (L) - R19-2 |
Always |
Below 1 Ω |
J28-25 (E3) - R19-3 |
J28-24 (ES) - Body ground |
J28-26 (L) or R19-2 - Body ground |
Always |
10 kΩ or higher |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
INSPECT FUEL SENDER GAUGE ASSEMBLY
(a) Remove the fuel sender gauge.
- for 1UR-FE (See page
)
- for 3UR-FE (See page
)
- for 3UR-FBE (See page
)
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
1 - 2 |
Float level is F (upper) |
12 to 18 Ω |
Float level is E (lower) |
405 to 415 Ω |
Result
Result | Proceed to |
OK |
A |
NG (for 1UR-FE) |
B |
NG (for 3UR-FE) |
C |
NG (for 3UR-FBE) |
D |
| B |
 |
REPLACE FUEL SENDER GAUGE ASSEMBLY |
| C |
 |
REPLACE FUEL SENDER GAUGE ASSEMBLY |
| D |
 |
REPLACE FUEL SENDER GAUGE ASSEMBLY |
| A |
 |
|
INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
(a) Remove the fuel suction with pump and gauge tube.
- for 1UR-FE (See page
)
- for 3UR-FE (See page
)
- for 3UR-FBE (See page
)
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
A2 - B2 |
Always |
Below 1 Ω |
A3 - B1 |
Result
Result | Proceed to |
OK |
A |
NG (for 1UR-FE) |
B |
NG (for 3UR-FE) |
C |
NG (for 3UR-FBE) |
D |
| A |
 |
REPLACE COMBINATION METER ASSEMBLY |
| B |
 |
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
| C |
 |
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
| D |
 |
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
|
Was this page helpful?