The combination meter assembly receives vehicle speed signals from the skid control ECU via the CAN line. The vehicle speed sensor detects the voltage that varies according to the vehicle speed. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage.
WIRING DIAGRAM
PROCEDURE
CHECK CAN COMMUNICATION SYSTEM
(a) Check if a CAN communication system DTC is output (See page ).
Result
Result
Proceed to
CAN communication system DTC is not output
A
CAN communication system DTC is output
B
B
GO TO CAN COMMUNICATION SYSTEM
A
CHECK SFI SYSTEM (VEHICLE SPEED)
(a) Check if a SFI system DTC is output.
for 1UR-FE (See page )
for 3UR-FE (See page )
for 3UR-FBE (See page )
Result
Result
Proceed to
SFI system DTC is not output
A
SFI system (for 1UR-FE) DTC is output
B
SFI system (for 3UR-FE) DTC is output
C
SFI system (for 3UR-FBE) DTC is output
D
B
GO TO DIAGNOSTIC TROUBLE CODE CHART
C
GO TO DIAGNOSTIC TROUBLE CODE CHART
D
GO TO DIAGNOSTIC TROUBLE CODE CHART
A
PERFORM ACTIVE TEST USING TECHSTREAM (SPEEDOMETER)
(a) Operate the Techstream according to the display and select "Active Test" (See page ).
Combination Meter:
Tester Display
Test Part
Control Range
Diagnostic Note
Speed Meter Operation
Speedometer
0, 40, 80, 120, 160 or 200
Acceptable range (km/h or mph): [Control range → Speedometer display]
for mph
40 mph → 39.3 to 42 mph
80 mph → 79.8 to 84 mph
for km/h
40 km/h → 38.5 to 43 km/h
80 km/h → 78.9 to 84 km/h
120 km/h → 119.6 to 125 km/h
160 km/h → 160.3 to 165 km/h
OK:
Needle indication is normal.
HINT:
Confirm that the vehicle is stopped and engine is idling. It is normal that door will be locked automatically when performing the speedometer Active Test.
The displayed value has the same units (km/h, mph) as the main scale of the vehicle's speedometer.
The needle position should be within the acceptable tolerance.
NG
REPLACE COMBINATION METER ASSEMBLY
OK
READ VALUE USING TECHSTREAM (VEHICLE SPEED)
(a) Operate the Techstream according to the display and select "Data List" (See page ).
Combination Meter:
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed Meter
Vehicle speed/Min.: 0 (0), Max.: 255 (158)
Almost same as actual speed (when driving)
Unit: km/h (mph)
OK:
Vehicle speed displayed on Techstream is almost the same as actual vehicle speed measured using speedometer tester (calibrated chassis dynamometer).
OK
REPLACE COMBINATION METER ASSEMBLY
NG
READ VALUE USING TECHSTREAM (WHEEL SPEED SENSOR)
(a) Operate the Techstream according to the display and select "Data List" (See page ).
ABS/VSC/TRAC:
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
Front wheel speed sensor RH reading
Min.: 0 km/h, Max.: 326 km/h
Actual wheel speed
Similar speed as indicated on speedometer
FL Wheel Speed
Front wheel speed sensor LH reading
Min.: 0 km/h, Max.: 326 km/h
Actual wheel speed
Similar speed as indicated on speedometer
RR Wheel Speed
Rear wheel speed sensor RH reading
Min.: 0 km/h, Max.: 326 km/h
Actual wheel speed
Similar speed as indicated on speedometer
RL Wheel Speed
Rear wheel speed sensor LH reading
Min.: 0 km/h, Max.: 326 km/h
Actual wheel speed
Similar speed as indicated on speedometer
OK:
Vehicle speed displayed on Techstream is almost the same as actual vehicle speed measured using speedometer tester (calibrated chassis dynamometer).
OK
REPLACE COMBINATION METER ASSEMBLY
NG
REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)