Chassis, Axles, Steering

Subframe

15steps
~90min
4/5difficulty
0204060801004030N·mlb·ft
Tightening torque found on this page
Done 0 of 15

Installation overview - Subframe


Note
  • Welding and straightening work on load-bearing and wheel-guiding components of the wheel suspension is not permitted.
  • Always replace self-locking nuts.
  • Always replace corroded bolts/nuts.
  • Rubber-metal bearings have a limited rotation range. Therefore, only tighten the bolted connections on components with rubber-metal bearings once the wheel bearing housing is raised (unladen position).
VW UP. Fahrwerk, Achsen, Lenkung

  1. Subframe
    • Secure
    • Remove and install
    • different versions
    • Assignment → Electronic Parts Catalog "ETKA"
  2. Stabilizer bar
    • Remove and install
  3. Clamp
  4. Bearing
    • Replace
  5. Nut
    • 40 N·m
    • Self-locking
    • replace after every removal
  6. Stabilizer link
    • Stabilizer bar connection to strut
  7. Nut
  8. Bolt
    • M12 x 1,5 x 75
    • 70 N·m and continue turning 180º
    • replace after every removal

If the thread of the weld nut is damaged, the thread can be repaired with a Heli-Coil thread insert.

Repair thread in side member.

  1. Bolt
    • M10 x 80
    • 50 N·m and continue turning 180º
    • replace after every removal

If the thread of the weld nut is damaged, the thread can be repaired with a Heli-Coil thread insert.

Repair thread in side member.

  1. Bolt
    • 70 N·m + continue turning 90º
    • replace after every removal
  2. Lower control arm
    • Remove and install
  3. Bolt
    • 70 N·m and continue turning 180º
    • replace after every removal
  4. Bolt
    • 40 N·m and continue turning 90º
    • replace after every removal
  5. Bolt
    • 40 N·m and continue turning 90º
    • replace after every removal
  6. Torque strut
    • different versions
    • Assignment → Electronic Parts Catalog "ETKA"
  7. Bolt
    • 20 N·m and continue turning 90º
    • replace after every removal

Secure subframe

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Securing fixture -T10486-
VW UP. Fahrwerk, Achsen, Lenkung

  • Engine and Transmission Hoist -V.A.G 1383 A-

Carry out the following work:


Caution!

The fixing tools -T10486- have different threads:

  • Fixing tool -T10486/1-: M12x1.5 (insert for fixing the subframe at the rear section)
  • Fixing tool -T10486/2-: M10 (insert for fixing the subframe at the front section)
VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew bolts for torque strut -1- and -2- from the transmission.

- Position engine and transmission jack -V.A.G 1383 A- under the subframe.

- Clean the threads of fixing tool -T10486-.

Be sure to observe the sequence for the following work steps.

VW UP. Fahrwerk, Achsen, Lenkung

To secure the subframe, fixing tools -T10486/2- must be screwed in one after the other at positions -1-.

Fixing tools -T10486/1- must be screwed in one after the other at positions -2-.

Positions -1- must be secured first.


Note

Fixing tools -T10486/2- must only be tightened to a maximum of 20 N·m, otherwise the thread of the fixing bolts will be damaged.

VW UP. Fahrwerk, Achsen, Lenkung

- Replace bolts -1- one after the other on both sides of the vehicle with fixing tools -T10486/2- and tighten to 20 N·m.

- Replace bolts -2- one after the other on both sides of the vehicle with fixing tools -T10486/1- and tighten to 20 N·m.

- Fixing the subframe is complete when all 4 bolts have been replaced one after the other with fixing tools -T10486/1- and fixing tools -T10486/2-.

Continue with removing subframe.

Continue with removing stabilizer bar.

Continue with removing and installing steering gear.

Remove fixing tools -T10486/1- and fixing tools -T10486/2-.

Removal of fixing tools -T10486/1- and fixing tools -T10486/2- is carried out in reverse order. Observe the following:

VW UP. Fahrwerk, Achsen, Lenkung

- Only unscrew one fixing bolt at a time and replace it with a new bolt -1- and -2-.

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques


Lower subframe

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Engine and Transmission Hoist -V.A.G 1383 A-

Carry out the following work:

Removing

- Turn steering wheel to straight-ahead position and remove ignition key so that the steering wheel lock engages.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew bolts -1- and remove footwell trim -2-.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew bolt -arrow- from universal joint -1- and pull universal joint off in direction of -arrow-.

- Remove underbody noise insulation → Body assembly work exterior.

VW UP. Fahrwerk, Achsen, Lenkung

- Pull retaining rings -1- for exhaust pipe off subframe.

- Loosen double clamp of exhaust system.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew hexagon nut -1- from right and left coupling rod.

- Pull coupling rod -3- out of stabilizer bar -2- on right and left side.

- Secure subframe.

- Lower subframe by a maximum of 10 cm.

Installing

Install in reverse order.

- Install underbody noise insulation → Body assembly work exterior.


Note

Make sure the bellows are undamaged and not twisted.

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques


Remove and install subframe without steering gear

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque Wrench -V.A.G 1331-
VW UP. Fahrwerk, Achsen, Lenkung

  • Torque Wrench -V.A.G 1332-

Carry out the following work:

Removing

- Loosen wheel bolts.

- Raise the vehicle.

- Remove wheels.

- Remove underbody noise insulation → Body assembly work exterior.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew nuts -arrows-.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew hexagon nut -1- from right and left coupling rod.

- Pull coupling rod -3- out of stabilizer bar -2- on right and left side.

VW UP. Fahrwerk, Achsen, Lenkung

- Pull retaining rings -1- for exhaust pipe off subframe.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew steering gear from subframe -arrows- and secure it with wire, for example.

- Secure subframe.

- Lower subframe with engine and transmission jack -V.A.G 1383 A-.

Installing

- Bolt subframe in place.

Installation is carried out in reverse order.

- Install wheels and tighten.

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques


Remove and install stabilizer bar

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque Wrench -V.A.G 1331-
VW UP. Fahrwerk, Achsen, Lenkung

  • Torque Wrench -V.A.G 1332-

Carry out the following work:

Removing

- Loosen wheel bolts.

- Raise the vehicle.

- Remove front wheels.

- Remove underbody noise insulation → Body assembly work exterior.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew hexagon nut -1- from right and left coupling rod.

- Pull coupling rod -3- out of stabilizer bar -2- on right and left side.

VW UP. Fahrwerk, Achsen, Lenkung

- Pull retaining rings for exhaust pipe off subframe.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew steering gear from subframe -arrows- and secure it with wire, for example.

- Secure subframe.

- Lower subframe with engine and transmission jack -V.A.G 1383 A-.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew bolts -arrows-.

- Remove stabilizer bar -1- toward the rear.

Installing

- Insert stabilizer bar and bolt to subframe with clamps.

- Bolt subframe in place.

Installation is carried out in reverse order.

- Install wheels and tighten.

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques


Replace stabilizer bar bearings

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque Wrench -V.A.G 1331-
VW UP. Fahrwerk, Achsen, Lenkung

  • Torque Wrench -V.A.G 1332-

Carry out the following work:

Removing

- Remove underbody noise insulation → Body assembly work exterior.

- Raise wheel bearing housing to unladen position.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew bolts -arrows-.

- Pull stabilizer bar clamp off bearing.

- Remove bearing from stabilizer bar.

Installing

VW UP. Fahrwerk, Achsen, Lenkung

- Install new bearings -1- on stabilizer bar through the opening -arrow-.


Note
  • Make sure that the outer edge of bearing -1- rests against stop -2-.
  • Depending on the version, stop -2- may be located to the right or left of the bearing.
VW UP. Fahrwerk, Achsen, Lenkung

- Bolt clamps to subframe -arrows-.

- Install underbody noise insulation → Body assembly work exterior.

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques