Chassis, Axles, Steering

Wheel bearing

51steps
~306min
4/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 51

Assembly overview - Wheel bearing

VW UP. Fahrwerk, Achsen, Lenkung

  1. Driveshaft
  2. Wheel bearing housing
    • Remove and install
    • Assignment → Electronic Parts Catalog "ETKA"
  3. Hex socket head bolt
    • 8 N·m
  4. Speed sensor
    • Before installing the sensor, clean the inner surface of the bore and coat it with solid lubricant paste -G 000 650-.
  5. Brake disc
  6. Wheel hub
    • Remove and install
  7. Circlip
    • installed with opening facing down
  8. Wheel bearing
    • Remove and install
  9. Bolt
    • 12 N·m
  10. Brake dust shield
  11. Bolt
    • 4,5 N·m
  12. 12-point nut, self-locking
    • Pre-tighten to 200 N·m, then loosen by 180° and tighten further to 50 N·m + 45°
    • replace after every removal

Replacing wheel bearing

VW UP. Fahrwerk, Achsen, Lenkung

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Pressure piece -3002-
  • Assembly tool -T10064-
  • Assembly tool -T10205-
  • Torque Wrench -V.A.G 1331-
  • Torque Wrench -V.A.G 1332-
  • Engine and Transmission Hoist -V.A.G 1383 A-
VW UP. Fahrwerk, Achsen, Lenkung

  • Torque wrench -V.A.G 1410-
  • Pressure piece -V.A.G 1459B-6- from hydraulic removal and installation device -V.A.G 1459B-
  • Pressure sleeve -V.A.G 1459B/2-8- from supplementary set -V.A.G 1459B/2-
  • Hydraulic cylinder -VAS 6178-
  • Foot pump -VAS 6179-
  • -2- Puller -Kukko 18/0-
  • -3- Separator -Kukko 17/1-
  • Ejector -T10520-

Carry out the following work:

Removing

- Raise vehicle until front axle is relieved of load.

- Loosen 12-point nut for driveshaft.


Caution!

If wheel-side driveshaft bolt connection is loose, wheel bearings must not be loaded.

If the wheel bearings are loaded by the weight of the vehicle, they will be pre-damaged. This reduces the service life of the wheel bearings.

The bolt for the driveshaft may be loosened by a maximum of 90º if the vehicle is standing on its wheels.

Vehicles without driveshaft must not be moved, otherwise the wheel bearing will be damaged. If a vehicle must nevertheless be moved, observe the following:

  • Install an outer CV joint instead of the driveshaft.
  • Tighten outer CV joint to 120 N·m.

- Loosen wheel bolts.

- Raise the vehicle.

- Remove wheel.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew hexagon nut -1- from right and left coupling rod.

- Pull coupling rod -3- out of stabilizer bar -2- on right and left side.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew nuts -arrows-.

- Pull control arm out of ball joint.

- Pull the driveshaft out of the wheel hub.

If the driveshaft cannot be pulled out of the wheel bearing, press the driveshaft out of the wheel bearing with puller -T10520-.

VW UP. Fahrwerk, Achsen, Lenkung

Before using extractor -T10520-, make sure pressure piece -1- is fitted.

VW UP. Fahrwerk, Achsen, Lenkung

Using puller -T10520-:

- Attach puller -T10520--1- to wheel hub with 2 wheel bolts.

VW UP. Fahrwerk, Achsen, Lenkung

- Be sure to observe the specified sequence.

  1. Tighten knurled nut -1- by hand.
  2. Turn only bolt -2- with a wrench and press driveshaft out using puller -T10520-.

Note

At the end of the procedure, or before retightening, return the spindle to its starting position so the hydraulic action can be used!

- Secure driveshaft to body with binding wire.

The driveshaft must not be allowed to hang down!

Otherwise the inner joint will be damaged by over-articulation.

- Remove the brake caliper and hang it with wire from the body → Brake systems.

- Unscrew the brake disc bolt and remove the brake disc.

- Remove the brake dust shield.

- Remove the ABS speed sensor → Brake systems.


Note

Position engine and transmission jack -V.A.G 1383/A- underneath (risk of accident from parts falling when the wheel hub and wheel bearing are pressed out).

VW UP. Fahrwerk, Achsen, Lenkung

Pressing out wheel hub

VW UP. Fahrwerk, Achsen, Lenkung

- Attach gripping pieces -T10064/6A--1- to the wheel hub.

- Screw wheel bolt -2- into the wheel hub and secure the lower gripping piece -T10064/6A-.

- Install the tools as shown in the illustration and preload the hydraulic cylinder -VAS 6178-.


Note

Make sure the wheel bolt -arrow- is offset from the crossbar -8-.

  1. Gripping pieces -T10064/6A-
  2. Wheel bolt
  3. Tube -T10064/1-
  4. Pressure plate -T10205/1-
  5. Hydraulic cylinder -VAS 6178- with pressure head -T10205/13-
  6. Nut -T10205/8-2-
  7. Spindle -T10205/8-1-
  8. Crossbar from tube -T10064/1-

- Press out the wheel hub while holding the tool in place.

- Remove the circlip -1-.

VW UP. Fahrwerk, Achsen, Lenkung

Pressing out wheel bearing

VW UP. Fahrwerk, Achsen, Lenkung

  1. Spindle -T10205/8-1-
  2. Nut -T10205/8-2-
  3. Pressure piece -V.A.G 1459B-6-
  4. Pressure sleeve -V.A.G 1459B/2-8-
  5. Pressure plate -T10205/1-
  6. Hydraulic cylinder -VAS 6178- with pressure head -T10205/13-
  7. Nut -T10205/8-2-

- Press out the wheel bearing while holding the tool in place.

Pulling inner race of wheel bearing off the wheel hub

  1. Puller, e.g. -Kukko 18/0-
  2. Pressure piece -3002-
  3. Inner race
  4. Separator, e.g. -Kukko 17/1-
  5. Wheel hub

Installing

- Clean the bore of the wheel bearing housing.

VW UP. Fahrwerk, Achsen, Lenkung

- Coat the entire bore with Molypaste -G 052 723 A2-.

Use the grease pad from the repair kit.

VW UP. Fahrwerk, Achsen, Lenkung

Pressing in wheel bearing

Observe installation position:

The black ring of the wheel bearing must face the wheel bearing housing (vehicle inside).

VW UP. Fahrwerk, Achsen, Lenkung

  1. Nut -T10205/8-2-
  2. Pressure piece -T10064/4-, with the large diameter facing the wheel bearing housing
  3. Wheel bearing
  4. Pressure piece -T10064/2-
  5. Pressure plate -T10205/1-
  6. Hydraulic cylinder -VAS 6178- with pressure head -T10205/13-
  7. Nut -T10205/8-2-
  8. Spindle -T10205/8-1-

- Press in the wheel bearing up to the stop.

Do not tilt the wheel bearing while pressing it in.

- Install the circlip -1-.


Note

The opening of the circlip -1- must point downward -arrow-.

VW UP. Fahrwerk, Achsen, Lenkung

Pressing in wheel hub

VW UP. Fahrwerk, Achsen, Lenkung

  1. Spindle -T10205/8-1-
  2. Nut -T10205/8-2-
  3. Pressure piece -V.A.G 1459B-6-
  4. Wheel hub
  5. Pressure plate -T10205/1-
  6. Hydraulic cylinder -VAS 6178- with pressure head -T10205/13-
  7. Nut -T10205/8-2-

Press in the wheel hub up to the stop.

Make sure that deflector disc -1- is fully clipped onto outer CV joint.


Note
  • The lugs of deflector disc -1- must point toward outer CV joint.
  • Deflector disc -1- must contact the contact surface of outer CV joint -arrow-.


Note

VW UP. Fahrwerk, Achsen, Lenkung

If deflector disc -1- is not positioned correctly or has fallen off outer CV joint, drive it onto outer CV joint up to the stop with pressure piece -T10049-.

- Insert the outer joint of the driveshaft into the splines of the wheel hub as far as possible.

VW UP. Fahrwerk, Achsen, Lenkung

- Bolt ball joint to control arm with new nuts -arrows-.

Use new nuts!

Make sure the bellows are undamaged and not twisted.

- Install the ABS speed sensor.

- Install the brake dust shield, brake disc and brake caliper → Brake systems.

- Install the brake hose bracket on the wheel bearing housing → Brake systems.

- Attach the stabilizer link to the stabilizer bar.

- Install wheel and tighten.

- Tighten 12-point nut for driveshaft.


Note

The vehicle must not be standing on its wheels during this step, otherwise the wheel bearing will be damaged.

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques


Removing and installing wheel bearing housing

VW UP. Fahrwerk, Achsen, Lenkung

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Ball joint puller -3287A-
  • Torque Wrench -V.A.G 1332-
  • Engine and Transmission Hoist -V.A.G 1383 A-
  • Torque angle wrench -V.A.G 1756-
  • Ejector -T10520-
VW UP. Fahrwerk, Achsen, Lenkung

  • Spreader -3424-

Carry out the following work:

Removing

- Raise vehicle until front axle is relieved of load.

- Loosen 12-point nut for driveshaft.


Caution!

If wheel-side driveshaft bolt connection is loose, wheel bearings must not be loaded.

If the wheel bearings are loaded by the weight of the vehicle, they will be pre-damaged. This reduces the service life of the wheel bearings.

The bolt for the driveshaft may be loosened by a maximum of 90º if the vehicle is standing on its wheels.

Vehicles without driveshaft must not be moved, otherwise the wheel bearing will be damaged. If a vehicle must nevertheless be moved, observe the following:

  • Install an outer CV joint instead of the driveshaft.
  • Tighten outer CV joint to 120 N·m.

- Loosen wheel bolts.

- Raise the vehicle.

- Remove wheel.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew hexagon nut -1- from right and left coupling rod.

- Pull coupling rod -3- out of stabilizer bar -2- on right and left side.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew nuts -arrows-.

- Pull control arm out of ball joint.

- Pull the driveshaft out of the wheel hub.

If the driveshaft cannot be pulled out of the wheel bearing, it can be pressed out of the wheel bearing using press-out tool -T10520-.

VW UP. Fahrwerk, Achsen, Lenkung

Before using press-out tool -T10520-, make sure that pressure piece -1- is installed.

VW UP. Fahrwerk, Achsen, Lenkung

Operating extractor -T10520-:

- Attach puller -T10520--1- to wheel hub with 2 wheel bolts.

VW UP. Fahrwerk, Achsen, Lenkung

- Be sure to observe the specified sequence.

  1. Tighten knurled nut -1- by hand.
  2. Turn only bolt -2- with a wrench and press driveshaft out using puller -T10520-.

Note

At the end of the procedure, or before retightening, return the spindle to its starting position so the hydraulic action can be used!

- Secure driveshaft to body with binding wire.

The driveshaft must not be allowed to hang down!

Otherwise the inner joint will be damaged by over-articulation.

- Remove the brake caliper and hang it with wire from the body → Brake systems.

- Remove the ABS speed sensor → Brake systems.

- Remove the brake disc → Brake systems.

- Remove the brake dust shield from the wheel bearing housing.

VW UP. Fahrwerk, Achsen, Lenkung

- Loosen nut -1- of tie rod end -2-, but do not unscrew it yet.


Caution!

Leave nut a few turns on the stud to protect the thread.

- Press tie rod end -2- off the steering arm.

- Position engine and transmission jack -V.A.G 1383 A- under the wheel bearing housing.

VW UP. Fahrwerk, Achsen, Lenkung

- Remove the bolted connection between the wheel bearing housing and the strut -arrow-.

VW UP. Fahrwerk, Achsen, Lenkung

- Insert spreader -3424- into slot of wheel bearing housing.

- Turn the ratchet 90º and pull it off the spreader -3424-.

- Pull the wheel bearing housing off the strut.


Note

If the wheel bearing housing is replaced, the ball joint must be modified. New nuts must be used for this.

Installing

Installation is in reverse order, observing the following:

VW UP. Fahrwerk, Achsen, Lenkung

Make sure that deflector disc -1- is fully clipped onto outer CV joint.


Note
  • The lugs of deflector disc -1- must point toward outer CV joint.
  • Deflector disc -1- must contact the contact surface of outer CV joint -arrow-.


Note

VW UP. Fahrwerk, Achsen, Lenkung

If deflector disc -1- is not positioned correctly or has fallen off outer CV joint, drive it onto outer CV joint up to the stop with pressure piece -T10049-.

- Insert the outer joint of the driveshaft into the splines of the wheel hub as far as possible.

VW UP. Fahrwerk, Achsen, Lenkung

- Bolt ball joint to control arm with new nuts -arrows-.

Use new nuts!

Make sure the bellows are undamaged and not twisted.

- Install the ABS speed sensor.

- Install the brake dust shield, brake disc and brake caliper → Brake System.

- Install the brake hose bracket on the wheel bearing housing → Brake systems.

- Attach the stabilizer link to the stabilizer bar.

- Install wheel and tighten.

- Tighten 12-point nut for driveshaft.


Note

The vehicle must not be standing on its wheels during this step, otherwise the wheel bearing will be damaged.

If the wheel bearing housing has been replaced, the vehicle must be measured (wheel alignment check).

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques