Replacing components
- All components of the refrigerant circuit that are sent in for quality monitoring must always be sealed (use the original sealing caps of the original part).
- The original parts A/C compressor, accumulator, liquid receiver, evaporator and condenser were previously filled with nitrogen gas. This charge is being phased out gradually, or the nitrogen charge pressure is now so low that no escaping gas can be perceived when the part is first opened.
- On vehicles with an A/C compressor without electromagnetic clutch, the engine may only be started when the refrigerant circuit is fully assembled (the A/C compressor runs continuously).
- To prevent damage to the A/C compressor with control valve for A/C compressor -N280- (without electromagnetic clutch) when the refrigerant circuit is empty, it is equipped with a secured oil supply. This means that approx. 40 to 50 cm3 of refrigerant oil remains in the A/C compressor.
![]()
Note
- As original parts are stored for a long time and in different locations, gas may or may not escape when the part is first opened (even with original parts of the same number). Therefore, carefully remove the sealing caps from the connections of the original parts and let the nitrogen gas escape slowly.
- The refrigerant circuit is fitted with either an orifice tube and an accumulator, or an expansion valve and a liquid receiver.
- Seal open connections and lines (to prevent moisture absorption).
- Always replace the orifice tube.
The accumulator / liquid receiver or desiccant bag cartridge does not need to be replaced under the following conditions.
- After an accident, but without damage to the accumulator / liquid receiver.
- The repair is carried out promptly (not exceeding the standard repair time) and no moisture has entered the system. The vehicle is no more than 5 years old.
- The receiver/drier or desiccant cartridge must be replaced under the following conditions.
- The refrigerant circuit has been opened and the vehicle is older than 5 years.
- The refrigerant circuit has been open for an unknown length of time (slow leak).
- The repair exceeds the standard repair time and moisture has entered the system.
- Always replace the receiver/drier or desiccant cartridge after blowing through with compressed air/nitrogen or flushing with refrigerant R134a. Keep the original part sealed for as long as possible so that moisture absorption is minimal.
- The A/C compressor has seized.
- The receiver/drier is damaged (accident).
![]()
Caution!
For handling refrigerant oil → Volkswagen ServiceNet, HS Environmental Protection, Waste Disposal, Current Status, Disposal Routes, Waste Oil Disposal, Refrigerant Oils.
For leaking or damaged components (except A/C compressor, receiver/drier or desiccant cartridge)
The refrigerant circuit was completely empty
- Remove defective component.
- Remove A/C compressor.
- Remove oil drain plug from A/C compressor.
![]()
Note
- To speed up draining of the refrigerant oil, turn the A/C compressor by hand via the V-ribbed belt pulley or clutch plate of the magnetic clutch.
- Pour out old refrigerant oil from the A/C compressor. For handling refrigerant oil → Volkswagen ServiceNet, HS Environmental Protection, Waste Disposal, Current Status, Disposal Routes, Waste Oil Disposal, Refrigerant Oils.
- Then fill the A/C compressor with the amount of new refrigerant oil that corresponds to the refrigerant oil quantity of the original-part A/C compressor.
- Do not use different refrigerant oils and quantities for different A/C compressors.
- To ensure lubrication of the A/C compressor at start-up, at least 80 cm3 of refrigerant oil must be filled into the A/C compressor. The remainder can be filled, e.g., into the new receiver/drier.
- If dirt has entered the A/C compressor while the refrigerant circuit was open (e.g. in an accident), the A/C compressor must be replaced.
- Blow through the refrigerant circuit with compressed air and dehumidify it with nitrogen.
- Replace receiver/drier or desiccant cartridge and orifice tube.
- Reassemble refrigerant circuit, evacuate and recharge.
Refrigerant is still in the refrigerant circuit
- Discharge refrigerant circuit.
- Remove defective component, blow through with compressed air, collect escaping refrigerant oil.
- The refrigerant oil quantity blown out (plus 20 cm3 for the evaporator, plus 10 cm3 for the condenser, refrigerant pipes and refrigerant hoses) must be filled into the new component as fresh refrigerant oil quantity.
- Replace orifice tube, depending on vehicle.
- Reassemble refrigerant circuit, evacuate and charge.
Replace A/C compressor
![]()
Note
On vehicles with an electrically driven A/C compressor, the high-voltage system must be de-energised before removing the A/C compressor.
Only if it is necessary to remove contamination from the refrigerant circuit (flushing), e.g. after external damage in an accident
- Discharge refrigerant circuit.
- Remove A/C compressor.
![]()
Note
If an A/C compressor with a different refrigerant oil is installed, the refrigerant circuit must be flushed with refrigerant R134a.
Electrically driven A/C compressor:
If an electrically driven refrigerant compressor is replaced without having a mechanical fault (e.g. defective circuit board), the refrigerant oil quantity must be determined from this refrigerant compressor.
![]()
Note
- The refrigerant compressor must be flushed so that the refrigerant oil to be determined is released from this refrigerant compressor.
- The refrigerant compressor is flushed in the direction of flow (from the low-pressure side inlet to the high-pressure side outlet).
- To flush as much refrigerant oil as possible out of the refrigerant compressor, position the refrigerant compressor during flushing so that the high-pressure side outlet is as low as possible.
- If an air conditioning service station without a flushing program is used, the procedure must be carried out manually (evacuate, flush 3 times with at least 2 kg of refrigerant each time and extract the refrigerant again, evacuate).
Determined quantity, e.g. 50 cm³
Then pour out enough refrigerant oil from the new refrigerant compressor so that only the quantity remaining in the new refrigerant compressor (plus 10 cm³) is left, equal to the quantity previously flushed out of the old refrigerant compressor. A new original refrigerant compressor has e.g. 200 cm³, so pour out only 140 cm³.
- Pour out the old refrigerant oil from the refrigerant compressor. For handling refrigerant oil → Volkswagen ServiceNet, HS Environmental Protection, Waste Disposal, Current Status, Disposal Routes, Waste Oil Disposal, Refrigeration Oils.
![]()
Note
If not enough refrigerant oil can be poured out of the new refrigerant compressor to be installed, the new refrigerant compressor must be flushed. After flushing, fill the new refrigerant compressor with as much new refrigerant oil as the quantity determined from the compressor being replaced.
Mechanically driven A/C compressor:
- Remove oil drain plug from A/C compressor.
- To speed up draining of the refrigerant oil, turn the A/C compressor, e.g. via the V-ribbed belt pulley / clutch plate of the magnetic clutch. Does not apply to electrically driven A/C compressors.
- Pour out the old refrigerant oil from the refrigerant compressor. For handling refrigerant oil → Volkswagen ServiceNet, HS Environmental Protection, Waste Disposal, Current Status, Disposal Routes, Waste Oil Disposal, Refrigeration Oils.
- Remove oil drain plug from the original-part A/C compressor, pour out the refrigerant oil and refill only the amount of fresh refrigerant oil that corresponds to the amount poured out (from the defective A/C compressor).
![]()
Note
- If, for example, 70 cm3 was poured out of the defective A/C compressor and 220 cm3 out of the original-part A/C compressor (a small amount of refrigerant oil remains in the A/C compressor), fill 70 cm3 of refrigerant oil into the A/C compressor being installed in this case. The refrigerant oil poured out of the original-part A/C compressor may be used.
- Do not use different refrigerant oils and quantities for the various A/C compressors.
- If a larger quantity of refrigerant oil (more than approx. 80 cm3) was poured out of the defective A/C compressor, the remaining refrigerant oil can also be filled into the evaporator or receiver/drier.
- Replace orifice tube, depending on vehicle.
- Reassemble refrigerant circuit, evacuate and charge.
Leak or internal damage (e.g. noise or no performance)
- Discharge refrigerant circuit.
- Remove A/C compressor.
![]()
Note
- In case of internal damage (to the A/C compressor), flush the refrigerant circuit with refrigerant R134a.
- If an A/C compressor with a different refrigerant oil is installed, the refrigerant circuit must be flushed with refrigerant R134a.
- Replace receiver/drier or desiccant cartridge and expansion valve, or receiver/drier and orifice tube. Only if no refrigerant remains in the circuit.
- In case of a leak, check the expansion valve for contamination or corrosion; replace the expansion valve if necessary.
- Reassemble refrigerant circuit, evacuate and charge.
Replace receiver/drier and orifice tube
After the refrigerant circuit has been freed of contamination, e.g. due to moisture ingress (refrigerant circuit was open for a longer period) or due to contamination
The accumulator / liquid receiver or desiccant bag cartridge does not need to be replaced under the following conditions.
- After an accident, but without damage to the accumulator / liquid receiver.
- The repair is carried out promptly (not exceeding the standard repair time) and no moisture has entered the system. The vehicle is no more than 5 years old.
The receiver/drier or desiccant cartridge must be replaced under the following conditions.
- The refrigerant circuit has been opened and the vehicle is older than 5 years.
- The refrigerant circuit has been open for an unknown length of time (slow leak).
- The repair exceeds the standard repair time and moisture has entered the system.
- Always replace the receiver/drier or desiccant cartridge after blowing through with compressed air/nitrogen or flushing with refrigerant R134a. Keep the original part sealed for as long as possible so that moisture absorption is minimal.
- The A/C compressor has seized.
- The receiver/drier is damaged (accident).
- Discharge refrigerant circuit.
- Remove A/C compressor.
- Eliminate the cause of the fault.
- Check the expansion valve for contamination or corrosion; replace it if necessary.
- Remove oil drain plug from A/C compressor.
- To speed up draining of the refrigerant oil, turn the A/C compressor, e.g. via the V-ribbed belt pulley / clutch plate of the magnetic clutch.
- Pour out the old refrigerant oil from the refrigerant compressor. For handling refrigerant oil → Volkswagen ServiceNet, HS Environmental Protection, Waste Disposal, Current Status, Disposal Routes, Waste Oil Disposal, Refrigeration Oils.
- Then fill the A/C compressor with the amount of new refrigerant oil that corresponds to the refrigerant oil quantity of the original-part A/C compressor.
![]()
Note
- Which refrigerant oils and quantities are to be used for the various A/C compressors.
- To ensure lubrication of the A/C compressor at start-up, at least 80 cm3 of refrigerant oil must be filled into the A/C compressor. The remainder can be filled, e.g., into the new receiver/drier.
- If dirt has entered the A/C compressor while the refrigerant circuit was open (e.g. in an accident), the A/C compressor must be replaced.
- Replace receiver/drier or desiccant cartridge and orifice tube.
- Reassemble refrigerant circuit, evacuate and charge.
Without the refrigerant circuit needing to be freed of contaminants (e.g. damage from an accident), no refrigerant has escaped and no moisture or dirt has entered the circuit
- Discharge refrigerant circuit.
- Replace orifice tube, depending on vehicle.
- Remove the receiver/drier or accumulator.
- Clean dirt from the receiver/drier or accumulator.
- Weigh the removed receiver/drier or accumulator.
![]()
Note
- Add refrigerant oil to the new receiver/drier or accumulator until it reaches the weight of the removed unit.
- Install the new receiver/drier or accumulator.
- Reassemble refrigerant circuit, evacuate and charge.