Air conditioning with R134a refrigerant

Complaints

~5min read

Possible complaints on the refrigerant circuit


Note

  • The air conditioning is working correctly if the air temperature at the outlets of the dashboard is 70 C or lower.
  • Setting on the Climatronic: "LO".
  • Setting on the air conditioning: "AC" on; "max"; "cold".

Test prerequisites:

  • The air conditioning self-diagnosis does not detect a fault using the Guided Fault Finding function of the Vehicle Diagnostic, Measurement and Information System -VAS 5051A-. The measured value block does not show a switch-off condition for the A/C compressor (only on vehicles with air conditioning self-diagnosis).

Possible complaints


Note

For all complaints marked with *.

  • Cooling has failed completely. *
  • Insufficient cooling performance at all vehicle speeds and engine speeds. *
  • No or insufficient cooling after several kilometers of driving. *
  • The A/C compressor, the A/C compressor magnetic clutch -N25- or the A/C compressor control valve -N280- is switched off by the A/C low-pressure switch -F73-, the magnetic clutch high-pressure switch -F118-, the A/C pressure switch -F129- or by the Climatronic control and display unit -E87- or the Climatronic control module -J255- due to excessively high or low pressure. *
  • No or sharply decreasing fresh air flow after several kilometers of driving (evaporator iced up). *

In addition, the following complaints may occur:

The A/C compressor makes noise

- Tighten the mounting bolts for the A/C compressor and the A/C compressor bracket with a torque wrench.

- Check the routing of the refrigerant lines. They must not contact other components and must be installed free of tension (align if necessary).

Noises occur immediately after switching on the A/C and/or when cornering or braking (refrigerant hammer):

- Drain, evacuate and refill the refrigerant circuit (too much refrigerant in the circuit).


Note

  • Too much refrigerant oil in the circuit can also cause this complaint (for example, the refrigerant oil quantity was not adjusted when the A/C compressor was replaced). For this complaint, flush the refrigerant circuit with refrigerant R134a.
  • The refrigerant must be drained from the A/C compressor. To make this easier, turn the poly-V pulley or clutch plate of the magnetic clutch on the A/C compressor by hand. Then add the total refrigerant oil quantity to the refrigerant circuit according to the → vehicle-specific repair manual (50 grams directly into the A/C compressor).

With an otherwise properly working A/C system, water sprays out of the air outlets (of the dashboard or in the footwell):

- Check that the condensate drain hose is routed correctly and is not pinched or kinked.

- Check the condensate drain valve. It must not be stuck with wax or underbody protection and must open and close properly.

- Check the water box cover. It must not be damaged and must be installed correctly (no water may run into the evaporator).

- Check the water box drains. They must not be blocked (for example by leaves).

Odors from the heating and A/C system

Does the odor come from the evaporator or heat exchanger?

  • Fishy odor

- Caused by a leak in the engine cooling system or in the heat exchanger of the heating and A/C system.


Note

If the fishy odor is weaker when the temperature is set to "cold" or stronger when set to "warm", check the heat exchanger for leaks.

  • Burnt clutch odor
  • Outgassing from floor mats, aftermarket seat covers, etc.
  • Foul, musty odor

- Caused by accumulation and deposits of leaves, pine needles, etc. in the water box.


Note

Clean the water box.

- Caused by water that cannot drain out of the water box.


Note

Check the water box drains.

  • Odor from the heating and A/C system


Note

Odors that can develop in the heating and A/C system can be detected in both fresh air and recirculation mode.

- Caused by too much condensation water in the heating and A/C system.


Note

Check the condensate drain in the vehicle-specific repair manual.

- Caused by an old or heavily soiled dust and pollen filter.


Note

Check the dust and pollen filter in the vehicle-specific repair manual.

- Caused by deposits on the evaporator fins.


Note

Clean the evaporator with the Ultrasonic A/C Cleaning Device -VAS 6189A- or the pressure cup gun -V.A.G 1538- and the appropriate spray lance.

Ultrasonic A/C Cleaning Device -VAS 6189A-

- The Ultrasonic A/C Cleaning Device -VAS 6189A- is placed in the passenger footwell and atomizes the Aero-Clean agent. Aero-Clean neutralizes microbes and bacterial contamination in the heating and A/C system.

An operating manual is supplied with the device.

Current equipment → ServiceNet; Workshop Equipment; Catalog; Workshop Equipment; Climate/Heating; Service Equipment

Spraying the evaporator with the pressure cup gun -V.A.G 1538- and spray lance

The evaporator is sprayed directly with Contra Sept using a spray lance (approx. 10 bar). Contra Sept neutralizes microbes and bacterial contamination directly at the evaporator.

To provide access to the evaporator, preparatory work and different spray lances are required, for example V.A.G 1538/5, V.A.G 1538/6 or V.A.G 1538/7.

A vehicle-specific operating manual is supplied with the Evaporator Cleaning Solution D 600 100 A2.

Current devices and spray lances → ServiceNet, "Search" function

Connecting the air conditioning service station

On vehicles with a connection on both the low-pressure and high-pressure side of the refrigerant circuit

Connecting the air conditioning service station for measuring and testing

- Switch the ignition off.

- Connect the air conditioning service station to the power supply.

- Connect the quick-release coupling adapters to the filling hoses of the air conditioning service station (hand wheels not screwed in, or hand shut-off valve not opened).

- Switch on the air conditioning service station and evacuate the filling hoses (only necessary if there is air in the filling hoses).

- Switch off the air conditioning service station.

- Unscrew the cap from the service connections (with valve).

- Connect the air conditioning service station to the refrigerant circuit of the vehicle via the service connections using the quick-release coupling adapters.

- Quick-release adapter spindle only far enough to safely open the valves at the refrigerant circuit connection (observe pressure gauges, do not overpressurize the valves).

- Carry out the planned test and measuring work.