Chassis, Axles, Steering

Steering gear

25steps
~150min
4/5difficulty
010203040502015N·mlb·ft
Tightening torque found on this page
Done 0 of 25

Assembly overview - steering gear

  • Repairs to the steering gear are not provided for. If faults are found, the steering gear must be replaced.
  • Only use steering gear grease -AOF 063 000 04- to grease the steering gear. However, do not overgrease the steering gear. Air equalization holes must remain clear. Otherwise the bellows will be damaged.
VW UP. Fahrwerk, Achsen, Lenkung

  1. Steering gear
    • Remove and install
  2. Wheel bearing housing
  3. Nut
    • 20 N·m and continue turning 90º
    • replace after every removal
  4. Subframe
    • Observe repair notes
  5. Bolt
    • Turn a further 180º after 50 N·m
    • replace after every removal

Removing and installing steering gear

VW UP. Fahrwerk, Achsen, Lenkung

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Ball joint puller -3287 A-
  • Torque Wrench -V.A.G 1331-
  • Insert tool SW 17, open ring -V.A.G 1331/10-
  • Torque Wrench -V.A.G 1332-
  • Engine and Transmission Hoist -V.A.G 1383 A-

Carry out the following work:

Removing

Only up!

- Disconnect ground strap from battery → Electrical system.

Only e-up!


WARNING!
  • Risk of injury! Observe warnings and safety regulations → Electrical System General Information.
  • Unscrew the ground strap from the battery → Electrical System.

Continuation for all vehicles

- Unscrew bolts -1- and remove footwell trim -2-.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew bolt -arrow- from universal joint -1- and pull universal joint off in direction of -arrow-.

- Loosen wheel bolts.

- Raise the vehicle.

- Remove front wheels.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew nuts -arrows-.

- Pull control arm out of ball joint.

VW UP. Fahrwerk, Achsen, Lenkung

- Loosen nut -1- of tie rod end -2-, but do not unscrew it yet.


Caution!

Leave nut a few turns on the stud to protect the thread.

- Press tie rod end -2- off the steering arm.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew hexagon nut -1- from right and left coupling rod.

- Pull coupling rod -3- out of stabilizer bar -2- on right and left side.

VW UP. Fahrwerk, Achsen, Lenkung

- Unscrew steering gear bolts -arrows- from subframe.

- Secure subframe.

- Lower subframe with engine and transmission jack -V.A.G 1383 A-.

- Remove steering gear towards the rear.

Installing

Installation is carried out in the reverse order. Observe the following:

Before installing the steering gear, the rack must be set to the center position.

VW UP. Fahrwerk, Achsen, Lenkung

- Move rack until dimension -a- is reached.

Dimension -a- = 76.5 mm

  • After fitting the steering gear to the universal joint, make sure the seal on the steering gear rests against the mounting plate without a kink. The opening to the footwell must seal correctly. Otherwise water ingress and/or noises may occur.
  • Make sure sealing surfaces are clean.
  • When replacing the steering gear, also replace the tie rod boots.

Before fitting the subframe bolts, position the steering gear on the subframe and fit the steering gear bolts.

- Bolt subframe in place.

VW UP. Fahrwerk, Achsen, Lenkung

- Bolt ball joint to control arm with new nuts -arrows-.

Make sure the bellows are undamaged and not twisted.

VW UP. Fahrwerk, Achsen, Lenkung

- Bolt steering gear to subframe -arrows-.

- Bolt tie rod to steering arm.

VW UP. Fahrwerk, Achsen, Lenkung

- Slide universal joint -1- onto the steering pinion.

- Insert new bolt -arrow- and tighten.

Only up!

- Connect ground strap to the battery → Electrical System.

Only e-up!


WARNING!
  • Risk of injury! Observe warnings and safety regulations → Electrical System General Information.
  • Connect ground strap to the battery → Electrical System.

Continuation for all vehicles

- Install wheels and tighten.

After installation, check the steering wheel position during a test drive.

If the steering wheel is crooked or a new steering gear has been installed, the front axle toe must be checked and adjusted if necessary!

- Check toe adjustment.

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques


Repairing steering gear

VW UP. Fahrwerk, Achsen, Lenkung

  1. Right tie rod end
    • marked with "A"
    • Remove and install
    • check
    • Installation position
  2. Nut
    • 50 N·m
  3. Clamp
  4. Boot
    • must not be twisted after adjusting toe
    • remove steering gear to replace
  5. Clamp
    • Replace
    • tension
  6. Gasket
    • Assignment → Electronic Parts Catalog "ETKA"
  7. Right tie rod
    • 80 N·m
    • Remove and install
    • supplied preset as a spare part
    • Adjust toe
  8. Steering gear
    • Assignment → Electronic Parts Catalog "ETKA"
    • Remove and install
  9. Left tie rod
    • 80 N·m
    • Remove and install
    • supplied preset as a spare part
    • check and adjust length
  10. Left tie rod end
    • marked with "B"
    • Remove and install
    • check
    • Installation position

Check tie rod ends for play, mounting and boots

- With vehicle raised (wheels hanging freely), check play by moving tie rods and wheels. Play: no play

- Check mounting.

- Check boots for damage and correct seating.

Removing and installing tie rod

VW UP. Fahrwerk, Achsen, Lenkung

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Gearbox holder -3221 A-
  • Clamping block -VW 313-
  • Hose clamp pliers -V.A.G 1275-
  • Torque Wrench -V.A.G 1332-
  • Open-end wrench insert SW 34 -V.A.G 1332/5-

Carry out the following work:

Removing

The tie rods can only be unscrewed and screwed on when the steering gear is removed.

- Remove steering gear.

- Clean steering gear externally in the area of the boot.

To remove the right tie rod, the clamp and hose clip of the left boot must be opened and the boot pushed back. To loosen the right tie rod, counter-hold the left rack on its wrench flats.

- Clamp steering gear in gearbox holder -T10108-.

- Open clamp and hose clip and push boot back.

- Unscrew tie rod from rack -1-. Counter-hold on the wrench flat of the rack with open-end wrench -3-.

  1. Gearbox holder -T10108-
  2. Open-end wrench SW 21
  3. Open-end wrench insert SW 34 -V.A.G 1332/5-
  4. Torque Wrench -V.A.G 1332-

Installing

- Check boot for wear (slots, cracks) and check boot sealing surfaces for cleanliness.

- Slide the boot onto the tie rod.

VW UP. Fahrwerk, Achsen, Lenkung

- Check dimension "a" on the tie rod and adjust if necessary.

Dimension -a- = 367 ± 1 mm

Before installation, check dimension "a" on new tie rods and adjust if necessary.

Afterwards, the total toe must be checked on the wheel alignment rack and adjusted if necessary, see Wheel Alignment.

VW UP. Fahrwerk, Achsen, Lenkung

- Screw the tie rod onto the rack -1-. Counter-hold the rack with open-end wrench -3- on the wrench flat on the rack.

  1. Gearbox holder -T10108-
  2. Open-end wrench SW 21
  3. Open-end wrench insert SW 34 -V.A.G 1332/5-
  4. Torque Wrench -V.A.G 1332-

- Turn the tie rod so that the tie rod end stud is in the installed position.

VW UP. Fahrwerk, Achsen, Lenkung

- Install the boot.

- Tighten the clamp with hose clamp pliers -V.A.G 1275-.

Use only original clamps.

The boot must not be installed twisted under any circumstances.

- Install the steering gear.

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques


Removing and installing tie rod end

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Ball joint press-out tool -T10187- Ball joint puller -3287 A-
VW UP. Fahrwerk, Achsen, Lenkung

  • Torque Wrench -V.A.G 1332-

Carry out the following work:

Removing

- Loosen wheel bolts.

- Raise the vehicle.

- Remove wheel.

VW UP. Fahrwerk, Achsen, Lenkung

- Loosen nut -1-.

- Mark the position of the tie rod end on the tie rod.

- Loosen nut -2- on the tie rod end, but do not remove it yet.


Caution!

Leave nut a few turns on the stud to protect the thread.

- Press the tie rod out of the wheel bearing housing and remove the nut.

  1. Ball joint press-out tool -T10187-

- Unscrew the tie rod end from the tie rod.

Installing

Installation is carried out in the reverse order. Observe the following:

VW UP. Fahrwerk, Achsen, Lenkung

- Make sure the correct tie rod end is installed on each side.

  1. Right tie rod end is marked with an "A".
  2. Left tie rod end is marked with a "B".

- Screw the tie rod end onto the tie rod up to the previously applied mark and secure it with the locknut.

- Insert the tie rod end into the wheel bearing housing.

- Fasten the tie rod end with a new nut.

- Install wheels and tighten.

- Check the vehicle alignment.

VW UP. Fahrwerk, Achsen, Lenkung

Tightening torques


Adjusting the steering gear

Two mechanics are required for the adjustment. Carry out the adjustment with the engine switched off.

- Raise the vehicle on the lift.

- Set the wheels to the straight-ahead position.

- Move the steering wheel alternately back and forth (approx. 30º about the center position). If steering play is excessive, a rattling noise can be heard.

- The second mechanic carefully turns adjusting screw -1- into the cover until the rattling noise is no longer audible in the vehicle interior.

- Carry out a test drive. Make sure that after cornering the steering returns to the straight-ahead position by itself (without binding).

VW UP. Fahrwerk, Achsen, Lenkung

- Secure adjusting screw -1- with 3 center punch marks -arrows-.

VW UP. Fahrwerk, Achsen, Lenkung