Ford Focus Quiz
Powertrain

Engine - Automatic Transaxle - Engine - 2.0L - Installation

In this manual: Powertrain
Vehicle - General — 4Accessories — 40Body — 237Chassis — 113Electrical — 19HVAC — 44Powertrain — 292
22steps
~142min
5/5difficulty
2special tools
0204060801004835N·mlb·ft
Tightening torque found on this page
Done 0 of 22
Special Tool(s)
2,200# Floor Crane, Fold Away 300-OTC1819E or equivalent
Lifting Bracket, Engine 303-050 (T70P-6000)
Powertrain Lift
300-OTC1585AE or equivalent
Spreader Bar
303-D089 (D93P-6001-A3) or equivalent
Adjustable Grip Arm, 1735A 014-00001 or equivalent

Material
Item Specification
Motorcraft® SAE 5W-20 Premium Synthetic Blend Motor Oil (US); Motorcraft® SAE 5W-20 Super Premium Motor Oil (Canada) XO-5W20-QSP (US); CXO-5W20-LSP12 (Canada) WSS-M2C945-A
Motorcraft® Multi-Purpose Grease XL-5 ESB-M1C93-B
  1. NOTE: Lubricate the torque converter pilot hub with multi-purpose grease.

    Check the installation depth of the torque converter.

    1. Lay a straightedge on the automatic transaxle flange.
    1. Check the installation depth between the transaxle flange and the torque converter centering spigot for the correct clearance.
  1. Using the Floor Crane and Spreader Bar, position the engine and transaxle together. Install the 6 bellhousing-to-engine fasteners.
    • Tighten to 48 N·m.
  2. Using the Floor Crane, Engine Lifting Bracket and Spreader Bar, raise the engine and transaxle assembly onto the lift table.
  1. Using the Powertrain Lift and Adjustable Grip Arm, secure the engine and transaxle assembly to the lift table.
  1. Install the 7 new catalytic converter manifold studs.
    • Tighten to 17 N·m.
  1. NOTICE: Only rotate the engine in a clockwise direction or engine damage may occur. NOTE:

    If new parts are not being used, be sure to align the marks on the flexplate and the stud made during engine removal.

    Install the 4 torque converter nuts.
    • Tighten to 35 N·m.
  1. Install the starter motor isolator.
  1. Install the starter motor, stud bolt and the bolt.
    • Install the upper bolt and lower stud bolt finger-tight.
    • Tighten the upper bolt to 35 N·m.
    • Tighten the lower stud bolt to 35 N·m.
  1. Position the 2 power steering tubes and the wiring harness as an assembly on the engine.
  1. Install the engine ground wire and the bolt.
    • Tighten to 48 N·m.
  1. Install the power steering tube bracket on the starter motor stud bolt and install the nut.
    • Tighten to 20 N·m.
  1. Attach the starter wire harness retainer to the starter motor stud bolt.
  1. Connect the starter motor electrical terminals and install the 2 nuts.
    • Tighten the small nut to 5 N·m.
    • Tighten the large nut to 12 N·m.
  1. Connect the Crankshaft Position (CKP) sensor electrical connector.
  1. Attach the 2 CKP sensor wire harness retainers.
  1. Connect the Power Steering Pressure (PSP) switch electrical connector.
  1. Connect the A/C compressor electrical connector.
  1. Connect the Turbine Shaft Speed (TSS) sensor electrical connector.
  1. Connect the Output Shaft Speed (OSS) sensor electrical connector.
  1. Position the Heated Oxygen Sensor (HO2S) and Catalyst Monitor Sensor (CMS) wire connector bracket and install the nut.
    • Tighten to 25 N·m.
  1. Install the nut for the HO2S and CMS wire connector bracket.
    • Tighten to 25 N·m.
  1. Using the lift table, position the engine and transaxle assembly in the vehicle.
  2. Install the transaxle mount plate and the 5 nuts.
    • Tighten the center nut to 150 N·m.
    • Tighten the 4 outer nuts to 48 N·m.
  1. Install the engine mount and the 2 bolts and the stud bolt.
    • Tighten to 48 N·m.
  1. Install the 2 motor mount nuts.
    • Tighten to 90 N·m.
  1. Install the 2 oil pan-to-bellhousing bolts.
    • Tighten to 48 N·m.
  1. Install the 2 lower bellhousing-to-oil pan bolts.
    • Tighten to 48 N·m.
  1. NOTE: The bolts are different lengths, make sure the bolts are in the correct location.

    Install the transaxle roll restrictor and the 2 bolts.

    1. Install the transaxle roll restrictor.
    1. Install the short bolt.
    1. Install the long bolt.
      • Tighten to 70 N·m.
  1. Position the transaxle fluid indicator tube and install the bolt.
    • Tighten to 8 N·m.
  1. Install the transaxle fluid indicator tube bracket bolt.
    • Tighten to 8 N·m.
  1. Attach the wire harness retainer to the transaxle fluid indicator tube.
  1. Install the transaxle fluid indicator.
  1. Connect the throttle control electrical connector.
  1. Connect the heater hose to the coolant tube.
  1. Connect the upper radiator hose, the heater hose to the coolant bypass.
  1. Install the power steering pump. For additional information, refer to Section 211-02.
  2. Clean and inspect the catalytic converter flange. Refer to Exhaust Manifold Cleaning and Inspection in Section 303-00.
  3. NOTICE: Failure to tighten the catalytic converter nuts to specification before installing the converter bracket bolts will cause the converter to develop an exhaust leak. NOTICE: Failure to tighten the catalytic converter nuts to specification a second time will cause the converter to develop an exhaust leak. Using a new gasket and 7 new nuts, install the catalytic converter and tighten in 2 stages in the sequence shown.
    • Stage 1: Tighten to 55 N·m.
    • Stage 2: Tighten to 55 N·m.
  1. Install the heat shield and 6 bolts.
    • Tighten to 11 N·m.
  1. Install the catalytic converter support bracket and the 2 bolts.
    • Tighten to 22 N·m.
  1. Install the 2 catalytic converter support bracket-to-engine bolts.
    • Tighten to 48 N·m.
  1. NOTE: Clean the mating surfaces of the muffler and tail pipe assembly and flexpipe.

    Using a new gasket and 2 new nuts, connect the flexpipe to the muffler and tail pipe assembly.

    • Tighten to 48 N·m.
  1. Using 2 new O-ring seals, install the power steering tubes to the steering gear and install the bolt.
    • Tighten to 18 N·m.
  1. Install the power steering tube clip and the bolt.
  1. Install the LH halfshaft. For additional information, refer to Section 205-04.
  2. NOTE: Lubricate the engine oil filter gasket with clean engine oil prior to installing the oil filter.

    Install a new engine oil filter.

    • Tighten the oil filter three-fourths turn after the oil filter gasket makes contact with the oil filter adapter.
  1. Connect the lower radiator hose to the radiator.
  1. Install the cooling fan motor and shroud. For additional information, refer to Section 303-03.
  2. Using 2 new O-ring seals, connect the A/C tubes to the compressor.
  1. Install the A/C tube bracket to the A/C compressor stud bolt and install the nut.
    • Tighten to 10 N·m.
  1. Install the 2 A/C tube nuts.
    • Tighten to 15 N·m.
  1. Position and attach the 4 B+ battery cable wire harness retainers (2 shown).
  1. Install the generator. For additional information, refer to Section 414-00.
  2. Install the accessory drive belt and tensioner. For additional information, refer to Section 303-05.
  3. Install the splash shield and the retainers.
  1. Install the 2 front wheels and tires. For additional information, refer to Section 204-04.
  2. Install the radio capacitor ground cable and the bolt.
    • Tighten to 10 N·m.
  1. Install the engine oil level indicator.
  1. Attach the shift cable to the retainer.
  1. Connect the 2 transaxle electrical connectors.
  1. Install the transmission fluid cooler tubes on the transaxle and slide the latches to the locked position.
  1. Install the secondary latches.
  1. Connect the transaxle shift cable to the lever and bracket.
  1. Connect the HO2S and CMS electrical connectors and attach the wire harness retainer.
  1. Connect the starter wire harness electrical connector.
  1. Connect the 3 PCM electrical connectors.
  1. Attach the engine harness to the coolant outlet bracket harness retainer.
  1. Connect and attach the 2 engine harness electrical connectors.
  1. Attach the brake booster vacuum hose retainer.
  1. Install the power brake booster vacuum tube into the quick connect fitting.
  1. Position and connect the Evaporative Emission (EVAP) tube. For additional information, refer to Section 310-00.
  1. Connect the fuel tube quick connect coupling to the fuel rail. For additional information, refer to Section 310-00.
  1. Install the negative battery cable ground and the bolt.
    • Tighten to 6 N·m.
  1. Attach the 2 positive battery cable wire harness retainer.
  1. Connect the positive battery cable nut.
    • Tighten to 10 N·m.
  1. Install the battery tray. For additional information, refer to Section 414-01.
  2. Connect the crankcase vent tube to the valve cover.
  1. Install the Air Cleaner (ACL) and ACL outlet pipe. For additional information, refer to Section 303-12.
  2. Fill the engine with clean engine oil.
  3. Fill and bleed the cooling system. For additional information, refer to Section 303-03.
  4. Evacuate and charge the A/C system. For additional information, refer to Section 412-00.

Test yourself

A quick Ford Focus quiz: every answer comes with an explanation and a link to the manual page.