Brakes

Bleeding Brake System

78steps
~468min
5/5difficulty
Done 0 of 78

Description

Work Procedure

When replace electrical brake control unit

ADVANCE PREPARATION

With CONSULT

  1. Ignition switch is ON.
  2. Operate the electric parking brake system.
  3. Select "ABS", "Work support", and "(Air bleeding) Accumulator pressure release" according to this order.
  4. Perform the work according to the directions of CONSULT.
>>

GO TO 2.

PERFORM AIR BLEEDING

With CONSULT

  1. Select "ABS", "Work support", and "(Air bleeding) Perform air bleeding" according to this order.
  2. Perform the work according to the directions of CONSULT.

    Supplementary explanation for air bleeding

    • : Low-pressure hose
    • : High pressure tube
  3. Connect a vinyl tube to the bleeder valve of the front brake.
  4. Depress the brake pedal to full stroke.
  5. Release the brake pedal.
  6. Wait for two seconds.
  7. Repeat step 4 to 6 until brake fluid coming out of brake calipers.
  8. Tighten the bleeder valve to the specified torque. Refer to FRONT BRAKE CALIPER ASSEMBLY : Exploded View.
  9. Connect a vinyl tube to the bleeder valve of the rear brake.
  10. Depress the brake pedal to full stroke.
  11. Release the brake pedal.
  12. Wait for two seconds.
  13. Repeat step 10 to 12 until brake fluid coming out of brake calipers.
  14. Tighten the bleeder valve to the specified torque. Refer to Exploded View.
  15. Connect a vinyl tube to the bleeder valve of the front brake.
  16. Depress the brake pedal half-way.
  17. Open the bleeder valve.
  18. Depress the brake pedal to full stroke.
  19. Tighten the bleeder valve.
  20. Wait for two seconds.
  21. Repeat steps 16 and 20 until the air is completely bleeds.
  22. Connect a vinyl tube to the bleeder valve of the rear brake.
  23. Depress the brake pedal half-way.
  24. Open the bleeder valve.
  25. Depress the brake pedal to full stroke.
  26. Tighten the bleeder valve.
  27. Wait for two seconds.
  28. Repeat steps 23 and 27 until the air is completely bleeds.
  29. Inspect brake fliud according to the directions of CONSULT.
  30. Perform learning according to the directions of CONSULT.

Did it learn correctly?

YES>>

GO TO 5.

NO>>

GO TO 3.

RELEARNING

With CONSULT

  1. Cancel electric parking brake system.
  2. Select "ABS", "Work support", and "(Air bleeding) Relearning" according to this order.
  3. Perform the work according to the directions of CONSULT.

Did it learn correctly?

YES>>

GO TO 5.

NO>>

Erase the memory of self-diagnosis results. GO TO 4.

FORCIBLY ELECTRICAL BRAKE CONTROL UNIT

With CONSULT

  1. Select "ABS", "Work support", and "(Air bleeding) Forcibly electrical brake control unit" according to this order.
  2. Perform the work according to the directions of CONSULT.

Did it learn correctly?

YES>>

GO TO 5.

NO>>

GO TO 1.

CHECK AIR POLLUTION

With CONSULT

Perform the work according to the directions of CONSULT.

  • To depress the brake pedal : within 20 seconds
  • To release the brake pedal : within 10 seconds
>>

INSPECTION END

When the electrical brake control unit is not replaced

ADVANCE PREPARATION

With CONSULT

  1. Ignition switch is ON.
  2. Operate the electric parking brake system.
  3. Select "ABS", "Work support", and "(Air bleeding) Accumulator pressure release" according to this order.
  4. Perform the work according to the directions of CONSULT.
>>

GO TO 2.

PERFORM AIR BLEEDING

With CONSULT

  1. Select "ABS", "Work support", and "(Air bleeding) Perform air bleeding" according to this order.
  2. Perform the work according to the directions of CONSULT.
  3. Connect a vinyl tube to the bleeder valve of the front brake.
  4. Depress the brake pedal to full stroke.
  5. Release the brake pedal.
  6. Wait for two seconds.
  7. Repeat step 4 to 6 until brake fluid coming out of brake calipers.
  8. Tighten the bleeder valve to the specified torque. Refer to FRONT BRAKE CALIPER ASSEMBLY : Exploded View.
  9. Connect a vinyl tube to the bleeder valve of the rear brake.
  10. Depress the brake pedal to full stroke.
  11. Release the brake pedal.
  12. Wait for two seconds.
  13. Repeat step 10 to 12 until brake fluid coming out of brake calipers.
  14. Tighten the bleeder valve to the specified torque. Refer to Exploded View.
  15. Connect a vinyl tube to the bleeder valve of the front brake.
  16. Depress the brake pedal half-way.
  17. Open the bleeder valve.
  18. Depress the brake pedal to full stroke.
  19. Tighten the bleeder valve.
  20. Wait for two seconds.
  21. Repeat steps 16 and 20 until the air is completely bleeds.
  22. Connect a vinyl tube to the bleeder valve of the rear brake.
  23. Depress the brake pedal half-way.
  24. Open the bleeder valve.
  25. Depress the brake pedal to full stroke.
  26. Tighten the bleeder valve.
  27. Wait for two seconds.
  28. Repeat steps 23 and 27 until the air is completely bleeds.
  29. Inspect brake fliud according to the directions of CONSULT.
  30. Perform learning according to the directions of CONSULT.

Did it learn correctly?

YES>>

GO TO 5.

NO>>

GO TO 3.

RELEARNING

With CONSULT

  1. Cancel electric parking brake system.
  2. Select "ABS", "Work support", and "(Air bleeding) Relearning" according to this order.
  3. Perform the work according to the directions of CONSULT.

Did it learn correctly?

YES>>

GO TO 5.

NO>>

Erase the memory of self-diagnosis results. GO TO 4.

FORCIBLY ELECTRICAL BRAKE CONTROL UNIT

With CONSULT

  1. Select "ABS", "Work support", and "(Air bleeding) Forcibly electrical brake control unit" according to this order.
  2. Perform the work according to the directions of CONSULT.

Did it learn correctly?

YES>>

INSPECTION END

NO>>

GO TO 1.

CHECK AIR POLLUTION

With CONSULT

Perform the work according to the directions of CONSULT.

  • To depress the brake pedal : within 20 seconds
  • To release the brake pedal : within 10 seconds
>>

INSPECTION END