Diagnosis and Repair Work Flow
Work Flow
DETAILED FLOW
INTERVIEW FROM THE CUSTOMER
>>GO TO 2.
CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by interview. Also check that the symptom is not caused by fail-safe mode. Refer to Fail-Safe.
>>GO TO 3.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
Ignition switch OFF (Auto ACC function OFF) to ON.
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES>>Record or print self-diagnosis results and freeze frame data (FFD). GO TO 4.
NO>>GO TO 6.
RECHECK THE SYMPTOM
With CONSULT
Erase self-diagnostic results for “ABS”.
Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).
Perform DTC confirmation procedures for the error-detected system.
Is DTC detected?
YES>>GO TO 5.
NO>>Check harness and connectors based on the information obtained by interview. Refer to Intermittent Incident.
REPAIR OR REPLACE ERROR-DETECTED PART
With CONSULT
Disconnect 12V battery negative terminal.
Repair or replace error-detected parts.
Reconnect part or connector after repairing or replacing.
Connect 12V battery negative terminal.
When DTC is detected, erase self-diagnostic result for “ABS”.
GO TO 7.
IDENTIFY ERROR-DETECTED SYSTEM BY SYMPTOM DIAGNOSIS
Estimate error-detected system based on symptom diagnosis and perform inspection.
Can the error-detected system be identified?
YES>>GO TO 7.
NO>>Check harness and connectors based on the information obtained by interview. Refer to Intermittent Incident.
FINAL CHECK
With CONSULT
Check the reference value for “ABS”.
Recheck the symptom and check that the symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES>>GO TO 3.
NO>>INSPECTION END
Diagnostic Work Sheet
DESCRIPTION
In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.
INTERVIEW SHEET SAMPLE
| Interview sheet | |||||
|---|---|---|---|---|---|
| Customer name | MR/MS | Registration number | Initial year registration | ||
| vehicle type | VIN | ||||
| Storage date | Engine / Traction motor | Mileage | km (Mile) | ||
| Symptom | □ Does not operate ( | ) function | |||
□ Warning lamp turns ON. □ |
) | ||||
| □ Noise (Location: ) □ Vibration (Location: ) | |||||
| □ Other ( | ) | ||||
| First occurrence | □ Recently □ Other ( | ) | |||
| Frequency of occurrence | □ Always □ Under a certain conditions of □ Sometimes ( time(s)/day) | ||||
| Climate conditions | □ Irrelevant | ||||
| Weather | □ Fine □ Cloud □ Rain □Snow □ Others ( | ) | |||
| Temperature | □ Hot □Warm □ Cool □ Cold □ Temperature [Approx. | °C (°F)] | |||
| Relative humidity | □ High □ Moderate □ Low | ||||
| Road conditions | □ Ordinary road □ Highway □ Mountainous road (uphill or downhill) □ Rough road | ||||
| Operating condition, etc. | □ Irrelevant □ When engine/traction motor starts □ During idling □ During driving □ During acceleration □ At constant speed driving □ During deceleration □ Immediately before stop [vehicle speed: Approx. km/h (MPH)] □ During cornering (right curve or left curve) □ When steering wheel is steered (to right or to left) |
||||
| Other conditions | VDC setting | □ On □ Off | |||
Use of other functions (ex. ICC) |
□ Yes □ No ( | ) | |||
| Presence of non-genuine parts installation | □ Yes □ No ( | ) | |||
| Memo | |||||