Brakes

Stroke Sensor Calibration

23steps
~138min
5/5difficulty
Done 0 of 23

Description

×: Necessary, -: Not necessary

ProcedureStroke sensor calibration
Removing/installing electrical brake control unit ×
Replacing electrical brake control unit ×
Removing/installing stroke sensor ×
Replacing stroke sensor ×
Removing/installing brake pedal ×
Replacing brake pedal ×
Adjusting brake pedal each height ×

Work Procedure

VEHICLE CONDITION

  1. Stop the vehicle.

  2. Turn the ignition switch OFF and disconnect CONSULT from data link connector.

>>

GO TO 2.

CHECK 12V BATTERY

Check the 12V battery. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Charge or replace the 12V battery. Refer toWork Flow or Removal and Installation. GO TO 3.

CHECKING INSTALLATION CONDITIONS OF BRAKE COMPONENTS

Check the installation conditions of brake components.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

CHECK BRAKE PEDAL

Check the brake pedal.

  • Brake pedal height: Refer to Inspection and Adjustment.
  • Brake pedal assembly: Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Adjust the brake pedal height or replace brake pedal assembly.

  • Adjust the brake pedal: Refer to Inspection and Adjustment.
  • Replace the brake pedal: Refer to Removal and Installation.

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Turn the ignition switch OFF to ON without depressing the brake pedal.

  2. Repeat step 1 two or more times.

  3. Turn the ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the vehicle, close all doors, check that the room lamp is OFF, and wait for 3 minutes or more without opening these doors.

  5. Turn the ignition switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “ABS”.

  7. Turn the ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the vehicle, close all doors, check that the room lamp is OFF, and wait for 3 minutes or more without opening these doors.

  9. Turn the ignition switch ON without depressing the brake pedal.

  10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

  11. Release brake pedal.

  12. Perform self-diagnosis for “ABS”.

Is a malfunction detected?

YES>>

Check the DTC. Refer to DTC Index. GO TO 6.

NO>>

GO TO 6.

PERFORM PEDAL STROKE SENSOR CALIBRATION

With CONSULT

  1. Turn the ignition switch OFF and disconnect CONSULT from data link connector and wait for 10 seconds or more.

  2. Turn the ignition switch ON without depressing the brake pedal.

  3. Start CONSULT and select "ABS" , "Work support" and "Stroke sensor calibration" according to this order.

  4. Touch “START”.

Is either “COMPLETED” or “The operation is incomplete. Try again after confirming the operation condition.” displayed?

“COMPLETED”>>

Touch the “END”. GO TO 7.

“The operation is incomplete. Try again after confirming the operation condition.”>>

GO TO 1.

CHECK DATA MONITOR

With CONSULT

Select “ABS”, “Data monitor” and “Stroke sensor output voltage” according to this order. Check that this signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

GO TO 6.

ERASE SELF-DIAGNOSIS MEMORY

With CONSULT

  1. Turn the ignition switch OFF and disconnect CONSULT from data link connector and wait for 10 seconds or more.

  2. Turn the ignition switch ON without depressing the brake pedal.

  3. Erase self-diagnosis result for “ABS”.

  4. Turn the ignition switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the vehicle, close all doors, check that the room lamp is OFF, and wait for 3 minutes or more without opening these doors.

Are the memories erased?

YES>>

INSPECTION END

NO>>

Check the items indicated by the self-diagnosis.