Body Interior

Door Mirror Motor

14steps
~84min
3/5difficulty
Done 0 of 14
Component Function Check

ACTIVE TEST

CONSULT

  1. Select “MIRROR MOTOR RH” and “MIRROR MOTOR LH” in “Active Test” mode of “AUTO DRIVE POS.”.

  2. Check that the function operates normally.

Test itemDescription
MIRROR MOTOR LH UP Door mirror LH Upward
DWN Downward
L Leftward
R Rightward
Off Stop
MIRROR MOTOR RH UP Door mirror RH Upward
DWN Downward
L Leftward
R Rightward
Off Stop

Is the inspection result normal?

YES>>

Door mirror motor function is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK DOOR MIRROR MOTOR INPUT SIGNAL

  1. Ignition switch ON.

  2. Check voltage between door mirror connector and ground.

    (+)(–)Door mirror remote control switch condition

    Voltage

    (Approx.)
    Door mirror
    ConnectorTerminal

    D4 (LH)

    D107 (RH)
    19 Ground UP Battery voltage
    Other than above 0V
    8 LEFT Battery voltage
    Other than above 0V
    7 DOWN / RIGHT Battery voltage
    Other than above 0V

Is the inspection result normal?

YES>>

Refer to Component Inspection.

NO>>

GO TO 2.

CHECK HARNESS CONTINUITY

  1. Ignition switch OFF.

  2. Disconnect automatic drive positioner control unit and door mirror.

  3. Check continuity between automatic drive positioner control unit connector and door mirror connector.

    Door mirror LH
    Automatic drive positioner control unitDoor mirror LHContinuity
    ConnectorTerminalConnectorTerminal
    M33 12 D4 7 Yes
    23 19
    24 8
    Door mirror RH
    Automatic drive positioner control unitDoor mirror RHContinuity
    ConnectorTerminalConnectorTerminal
    M33 10 D107 19 Yes
    11 8
    22 7
  4. Check continuity between automatic drive positioner control unit connector and ground.

    Door mirror LH
    Automatic drive positioner control unitGroundContinuity
    ConnectorTerminal
    M33 12 No
    23
    24
    Door mirror RH
    Automatic drive positioner control unitGroundContinuity
    ConnectorTerminal
    M33 10 No
    11
    22

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL

  1. Connect automatic drive positioner control unit.

  2. Ignition switch ON.

  3. Check voltage between automatic drive positioner control unit connector and ground.

    Door mirror LH
    (+)(-)Mirror switch condition

    Voltage

    (Approx.)
    Automatic drive positioner control unit
    ConnectorTerminal
    M33 12 Ground DOWN / RIGHT Battery voltage
    Other than above 0V
    23 UP Battery voltage
    Other than above 0V
    24 LEFT Battery voltage
    Other than above 0V
    Door mirror RH
    (+)(-)Mirror switch condition

    Voltage

    (Approx.)
    Automatic drive positioner control unit
    ConnectorTerminal
    M33 10 Ground UP Battery voltage
    Other than above 0V
    11 LEFT Battery voltage
    Other than above 0V
    22 DOWN / RIGHT Battery voltage
    Other than above 0V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace automatic drive positioner control unit. Refer to Removal and Installation.

CHECK DOOR MIRROR MOTOR

Check door mirror motor.

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Refer to Intermittent Incident.

NO>>

Replace door mirror actuator. Refer to Removal and Installation.

Component Inspection

CHECK DOOR MIRROR MOTOR 1

Check that door mirror motor does not trap foreign objects and does not have any damage.

Refer to Exploded View.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace door mirror actuator. Refer to Removal and Installation.

CHECK DOOR MIRROR MOTOR 2

  1. Ignition switch OFF.

  2. Disconnect door mirror.

  3. Apply 12V to each power supply terminal of door mirror motor.

    Door mirror connectorTerminalOperational direction
    (+)(–)

    D4 (LH)

    D107 (RH)
    7 8 RIGHT
    8 7 LEFT
    19 7 UP
    7 19 DOWN

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace door mirror actuator. Refer to Removal and Installation.